Acta
Library
32025R2621Implementing regulationin forceOJ authentic text

Commission Implementing Regulation (EU) 2025/2621 of 16 December 2025 laying down rules for the application of Regulation (EU) 2023/956 of the European Parliament and the Council as regards the establishment of default values

Published
16 December 2025
In force from
1 January 2026
Valid until
31 December 9999
Segments
2 articles · 12 recitals · 4 annexes
Official sourcesha2566e07a52233218bce912f6021875cbca48acd72fdbb78adb248439d4c52ab9fe1

Text reproduced from Publications Office of the European Union, retrieved 29 September 2026. Acta is unofficial, and the hash above identifies the bytes Acta stored — not an official instrument. Always check the official source before relying on it. Not legal advice.

Recitals

Recital 1

Article 7 of Regulation (EU) 2023/956 requires the use of default values for determining embedded emissions in goods other than electricity and in imported electricity , and for determining indirect embedded emissions .

Recital 2

In accordance with Article 7 of Regulation (EU) 2023/956 default values are to be determined on the basis of the methodology set out in Annex IV to that Regulation, which is to be based on the most up-to-date and reliable information. In the event that neither data obtained by the Joint Research Centre nor data collected during the transitional period is considered sufficiently reliable, the default values should be based on the average of the ten exporting countries with the highest emission intensities for which reliable data can be applied for that type of goods.

Recital 3

The environmental objective of the carbon border adjustment mechanism (‘the CBAM’) is to prevent carbon leakage. This objective would be compromised if importers of goods other than electricity were allowed to apply default values that are lower than the actual emissions embedded in those goods. At the same time, the default values including mark-ups need to be proportionate and necessary to contribute to achieving the CBAM objectives. Therefore, the default values including mark-ups should be determined using a conservative approach that ensures that embedded emissions are not underestimated when applying default values.

Recital 4

To ensure the environmental integrity of the CBAM, default values for embedded emissions of goods other than electricity should include a mark-up to account for the deviations of an individual installation with emission levels higher than the relevant average emission intensity of the producer country. Given the difficulties to verify that installation-specific data from third countries is of a sufficiently high quality, a suitable proxy should be applied to estimate the variations of individual installations compared to the average. Therefore, the proposed mark-up is based on existing deviations of Union installations with respect to Union average altogether.

Recital 5

To avoid immediate disproportionate impacts on prices of goods, and to give economic operators time to adapt, the mark-up should be gradually phased-in. This phase-in, is also necessary as the number of verifiers may increase in the first years following the end of the transition period, in particular in 2026. and hence CBAM declarants should therefore be able to use default values in those first years, and rely on actual emissions subsequently.

Recital 6

Specific considerations apply to the fertilisers sector where a lower mark-up should be applied.

Recital 7

For indirect embedded emissions, the default value should be calculated based on the average of the emission factor of the country-of-origin electricity grid. Such method of calculation is the most suitable to achieve both the prevention of carbon leakage as well as the preservation of the environmental integrity of the CBAM, given that it reflects to the largest possible degree decarbonisation efforts of third countries’ electricity grids while maintaining a high level of protection against the risk of carbon leakage. In order to reflect the impact of decarbonisation policies of third countries, such as the increase in renewable energy production, as well as climatic conditions on the yearly electricity supply in the countries concerned, whilst avoiding an excessive volatility of the emission factor due to anomalous years, including attributable to exceptional climatic conditions or other unforeseeable events, the emission factor should be calculated on the basis of the simple average of the emission factor for the most recent five-year period before the reporting for which reliable data is available.

Recital 8

For electricity imported into the customs territory of the Union, in order to reflect the impact of decarbonisation policies in the third country or group of third countries, on the emission intensity of the electricity production in the countries concerned, whilst avoiding an excessive volatility of the emission factor due to anomalous years, including attributable to exceptional climatic conditions or other unforeseeable events, the CO2 emission factor should be calculated on the basis of the average of the yearly CO2 emission factors for the most recent five-years period for which reliable data is available.

Recital 9

To provide certainty on the default values to be used for precursors for which the country of production is not known, such default values should be laid down. To prevent operators that use a precursor produced in a third country for which a high default has been set from claiming that the country of production of a precursor is unknown in order to avoid being subject to that high default value, where the country of production of a precursor cannot be identified, the default value to be used for that precursor should be the default value of the third country with the highest emission intensities for that precursor.

Recital 10

Where the Commission proceeds to revise this Implementing Act, it should conduct a public consultation to uphold transparency and to ensure a meaningful participation of all relevant stakeholders, in accordance with the Commission’s Better Regulation Guidelines.

Recital 11

The default values and mark-ups shall be revised by December 2027 at the latest. The Commission should make all necessary efforts, in close collaboration with the Member States and based on a systematic and holistic review, to ensure that a revision of the default values can already be carried out in 2026.

Recital 12

The measures provided for in this Regulation are in accordance with the opinion of the CBAM Committee,

Article 1

Default values
1.

Where the embedded emissions in imported goods are determined on the basis of default values in accordance with Article 7(2), point (b), of Regulation (EU) 2023/956, the default values laid down in Annex I to this Regulation shall be used.

2.

Where the embedded emissions of complex goods are determined on the basis of actual values, and the embedded emissions of precursors used in the production of those complex goods are determined on the basis of default values in accordance with Article 15 of Commission Implementing Regulation (EU) 2025/2547 (2), the default values laid down in Annex I shall be used for those precursors.

3.

Where the specific indirect embedded emissions are determined on the basis of default values in accordance with Article 7(4) of Regulation (EU) 2023/956, the default values laid down in Annex II to this Regulation shall be used.

4.

Where the embedded direct emissions in electricity imported into the customs territory of the Union are determined on the basis of default values in accordance with Article 7(3) of Regulation (EU) 2023/956, the default values laid down in Annex III to this Regulation shall be used.

5.

By way of derogation from paragraph 2, where a country of production cannot be identified for a precursor, the default values laid down in Annex IV shall be used.

anchor art_1 · hash 0b5ae55437cb74009ae091ce6a9440f477306ddf0d0d7beee6fac3f8025f8826

Article 2

This Regulation shall enter into force on the third day following that of its publication in the Official Journal of the European Union.

It shall apply from 1 January 2026.

It shall be revised in 2027 at the latest.

anchor art_2 · hash 07142900f204c55ea3c50db44771859c894e59c15c1d29c3840c11e34c57e307

Annex I

Default values for goods imported into the customs territory of the Union, except for electricity
Where a country or territory is not explicitly listed, the default value for the respective good from the table 'Other countries and territories' needs to be selected. Where a country or territory is explicitly listed but no value is provided or the relevant field shows '-', the default value for the respective good from the table 'Other countries and territories' needs to be selected. Where default values are used to determine the specific embedded emissions of a final good or of a precursor, the specific embedded free allocation shall be based on the corresponding underlying production route determining the CBAM benchmark (BM) as defined in Commission Implementing Regulation (EU) 2025/2620 (1) on the calculation of the free allocation adjustment to the number of CBAM certificates to be surrendered. The meaning of the indicators is as follows: (A) grey clinker / cement (B) white clinker / cement (C) Carbon Steel based on BF/BOF (D) Carbon Steel based on DRI/EAF (E) Carbon Steel based on Scrap/EAF (F) Low alloy Steel based on BF/BOF (G) Low alloy Steel based on DRI/EAF (H) Low alloy Steel based on scrap/EAF (J) High alloy Steel (based on EAF) (K) primary Aluminium (L) secondary Aluminium If no production route is indicated for a CN code, the CBAM benchmark (BM) is independent of the production route. Albania Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,870 0 0,870 0,957 1,044 1,131 (A) 2523 21 00 White Portland cement - - - 1,230 0,140 1,370 2523 29 00 Grey Portland cement 0,900 0,030 0,930 1,023 1,116 1,209 2523 90 00 White hydraulic cements - - - - - - (B) 2523 90 00 Grey hydraulic cements 0,860 0,030 0,890 0,979 1,068 1,157 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,730 0,040 2,760 2,788 2,788 2,788 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,190 0,050 2,240 2,262 2,262 2,262 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,030 0,470 0,475 0,475 0,475 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,730 0,030 0,760 0,768 0,768 0,768 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,330 0,080 1,420 1,434 1,434 1,434 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,300 0,080 1,390 1,404 1,404 1,404 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,060 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,380 0,070 1,460 1,475 1,475 1,475 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,650 0,050 1,700 1,717 1,717 1,717 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,540 0,080 2,620 2,646 2,646 2,646 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,080 2,220 2,242 2,242 2,242 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,080 2,220 2,242 2,242 2,242 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,260 0,060 4,310 4,353 4,353 4,353 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,130 0,070 2,200 2,222 2,222 2,222 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,560 0,070 1,620 1,636 1,636 1,636 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,570 0,080 1,640 1,656 1,656 1,656 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,060 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,080 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,060 0,770 0,778 0,778 0,778 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,050 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,040 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,450 0,090 1,540 1,555 1,555 1,555 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,080 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,060 1,490 1,505 1,505 1,505 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,040 0,770 0,778 0,778 0,778 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Algeria Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,290 0,060 1,340 1,474 1,608 1,742 (B) 2523 10 00 Grey clinker 1,240 0,040 1,280 1,408 1,536 1,664 (A) 2523 21 00 White Portland cement 1,230 0,140 1,370 1,507 1,644 1,781 2523 29 00 Grey Portland cement 1,230 0,060 1,300 1,430 1,560 1,690 2523 90 00 White hydraulic cements 1,280 0,170 1,440 1,584 1,728 1,872 (B) 2523 90 00 Grey hydraulic cements 1,170 0,070 1,240 1,364 1,488 1,612 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,490 0,040 2,530 2,555 2,555 2,555 2814 10 00 Anhydrous ammonia 1,960 0,120 2,080 2,101 2,101 2,101 2814 20 00 Ammonia in aqueous solution 0,590 0,040 0,620 0,626 0,626 0,626 2834 21 00 Nitrate of potassium 2 0,060 2,060 2,081 2,081 2,081 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,030 0,470 0,475 0,475 0,475 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,720 0,030 0,760 0,768 0,768 0,768 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,320 0,100 1,410 1,424 1,424 1,424 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,290 0,090 1,380 1,394 1,394 1,394 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,070 0,630 0,636 0,636 0,636 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,270 0,080 1,360 1,374 1,374 1,374 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,510 0,060 1,570 1,586 1,586 1,586 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,330 0,090 2,420 2,444 2,444 2,444 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,090 2,070 2,091 2,091 2,091 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,090 2,070 2,091 2,091 2,091 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,880 0,060 3,940 3,979 3,979 3,979 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,080 2,030 2,050 2,050 2,050 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,460 0,080 1,530 1,545 1,545 1,545 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,090 1,580 1,596 1,596 1,596 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,730 0,080 0,810 0,818 0,818 0,818 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,090 1,060 1,071 1,071 1,071 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,070 0,720 0,727 0,727 0,727 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,050 0,510 0,515 0,515 0,515 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,330 0,110 1,440 1,454 1,454 1,454 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,520 0,090 0,610 0,616 0,616 0,616 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,070 1,380 1,394 1,394 1,394 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,050 0,720 0,727 0,727 0,727 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,920 N/A 0,920 1,012 1,104 1,196 (L) 7604 10 10 Bars and rods 1,140 N/A 1,140 1,254 1,368 1,482 (L) 7604 10 90 Profiles 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7604 21 00 Hollow profiles 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7604 29 10 Bars and rods 1,140 N/A 1,140 1,254 1,368 1,482 (L) 7604 29 90 Profiles 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7605 Aluminium wire 1,140 N/A 1,140 1,254 1,368 1,482 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7608 Aluminium tubes and pipes 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7610 90 Other 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7610 90 90 Other 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,140 N/A 1,140 1,254 1,368 1,482 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,600 N/A 1,600 1,760 1,920 2,080 (L) 7616 99 10 Cast 0,920 N/A 0,920 1,012 1,104 1,196 (L) 7616 99 90 Other 1,600 N/A 1,600 1,760 1,920 2,080 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,180 0,030 0,210 0,231 0,252 0,273 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,870 N/A 2,870 3,157 3,444 3,731 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - - - - 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - - - - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 0,810 N/A 0,810 0,891 0,972 1,053 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 3 N/A 3 3,300 3,600 3,900 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 3 N/A 3 3,300 3,600 3,900 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3 N/A 3 3,300 3,600 3,900 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3 N/A 3 3,300 3,600 3,900 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 3 N/A 3 3,300 3,600 3,900 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 3 N/A 3 3,300 3,600 3,900 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 3 N/A 3 3,300 3,600 3,900 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 3 N/A 3 3,300 3,600 3,900 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 3 N/A 3 3,300 3,600 3,900 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 3 N/A 3 3,300 3,600 3,900 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 3 N/A 3 3,300 3,600 3,900 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 3 N/A 3 3,300 3,600 3,900 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 3 N/A 3 3,300 3,600 3,900 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 3 N/A 3 3,300 3,600 3,900 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 3 N/A 3 3,300 3,600 3,900 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 3 N/A 3 3,300 3,600 3,900 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 3 N/A 3 3,300 3,600 3,900 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 3 N/A 3 3,300 3,600 3,900 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 3 N/A 3 3,300 3,600 3,900 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 3 N/A 3 3,300 3,600 3,900 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 3 N/A 3 3,300 3,600 3,900 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 3 N/A 3 3,300 3,600 3,900 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 3 N/A 3 3,300 3,600 3,900 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,300 N/A 3,300 3,630 3,960 4,290 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,300 N/A 3,300 3,630 3,960 4,290 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,300 N/A 3,300 3,630 3,960 4,290 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,300 N/A 3,300 3,630 3,960 4,290 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,300 N/A 3,300 3,630 3,960 4,290 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,300 N/A 3,300 3,630 3,960 4,290 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,300 N/A 3,300 3,630 3,960 4,290 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,300 N/A 3,300 3,630 3,960 4,290 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,300 N/A 3,300 3,630 3,960 4,290 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,300 N/A 3,300 3,630 3,960 4,290 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,300 N/A 3,300 3,630 3,960 4,290 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,300 N/A 3,300 3,630 3,960 4,290 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,300 N/A 3,300 3,630 3,960 4,290 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,300 N/A 3,300 3,630 3,960 4,290 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,300 N/A 3,300 3,630 3,960 4,290 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,300 N/A 3,300 3,630 3,960 4,290 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 02 Semi-finished products of tool steel 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,520 N/A 4,520 4,972 5,424 5,876 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,410 N/A 3,410 3,751 4,092 4,433 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,520 N/A 4,520 4,972 5,424 5,876 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,410 N/A 3,410 3,751 4,092 4,433 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,410 N/A 3,410 3,751 4,092 4,433 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,410 N/A 3,410 3,751 4,092 4,433 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,410 N/A 3,410 3,751 4,092 4,433 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,190 N/A 3,190 3,509 3,828 4,147 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,870 N/A 2,870 3,157 3,444 3,731 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,300 N/A 3,300 3,630 3,960 4,290 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,300 N/A 3,300 3,630 3,960 4,290 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,300 N/A 3,300 3,630 3,960 4,290 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 3 N/A 3 3,300 3,600 3,900 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3 N/A 3 3,300 3,600 3,900 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,300 N/A 3,300 3,630 3,960 4,290 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,300 N/A 3,300 3,630 3,960 4,290 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,910 N/A 2,910 3,201 3,492 3,783 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,910 N/A 2,910 3,201 3,492 3,783 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 3 N/A 3 3,300 3,600 3,900 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,300 N/A 3,300 3,630 3,960 4,290 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,300 N/A 3,300 3,630 3,960 4,290 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 3 N/A 3 3,300 3,600 3,900 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 3 N/A 3 3,300 3,600 3,900 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,300 N/A 3,300 3,630 3,960 4,290 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,300 N/A 3,300 3,630 3,960 4,290 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,930 N/A 2,930 3,223 3,516 3,809 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,930 N/A 2,930 3,223 3,516 3,809 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,930 N/A 2,930 3,223 3,516 3,809 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,300 N/A 3,300 3,630 3,960 4,290 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 3 N/A 3 3,300 3,600 3,900 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 3 N/A 3 3,300 3,600 3,900 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,300 N/A 3,300 3,630 3,960 4,290 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3 N/A 3 3,300 3,600 3,900 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 3 N/A 3 3,300 3,600 3,900 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,860 N/A 2,860 3,146 3,432 3,718 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,860 N/A 2,860 3,146 3,432 3,718 7307 19 90 Cast tube or pipe fittings of steel 3 N/A 3 3,300 3,600 3,900 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,910 N/A 2,910 3,201 3,492 3,783 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,910 N/A 2,910 3,201 3,492 3,783 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,910 N/A 2,910 3,201 3,492 3,783 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,910 N/A 2,910 3,201 3,492 3,783 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 3 N/A 3 3,300 3,600 3,900 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 3 N/A 3 3,300 3,600 3,900 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 3 N/A 3 3,300 3,600 3,900 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 3 N/A 3 3,300 3,600 3,900 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,020 N/A 3,020 3,322 3,624 3,926 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3 N/A 3 3,300 3,600 3,900 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3 N/A 3 3,300 3,600 3,900 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,300 N/A 3,300 3,630 3,960 4,290 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 3 N/A 3 3,300 3,600 3,900 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,300 N/A 3,300 3,630 3,960 4,290 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 3 N/A 3 3,300 3,600 3,900 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 3 N/A 3 3,300 3,600 3,900 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 3 N/A 3 3,300 3,600 3,900 (C) 7318 16 Nuts of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 3 N/A 3 3,300 3,600 3,900 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 3 N/A 3 3,300 3,600 3,900 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7318 29 00 Non-threaded articles, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 3 N/A 3 3,300 3,600 3,900 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 3 N/A 3 3,300 3,600 3,900 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 30 Ladders and steps, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 98 Articles of iron or steel, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) Angola Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,220 0,040 0,250 0,275 0,300 0,325 (A) 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,240 0,020 1,260 1,386 1,525 1,677 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,240 0,030 1,270 1,397 1,537 1,690 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,180 0,040 1,220 1,342 1,476 1,624 (A) 2523 30 00 Aluminous cement - - - _ _ _ Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,617 N/A 0,617 0,678 0,740 0,802 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Argentina Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,030 0,900 0,990 1,089 1,198 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,870 0,050 0,920 1,012 1,113 1,225 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,900 0,030 1,930 1,949 1,949 1,949 2814 10 00 Anhydrous ammonia 2,260 0,100 2,360 2,384 2,384 2,384 2814 20 00 Ammonia in aqueous solution 0,680 0,030 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 1,680 0,050 1,730 1,747 1,747 1,747 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,020 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,020 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,080 1,600 1,616 1,616 1,616 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,070 1,570 1,586 1,586 1,586 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,050 0,720 0,727 0,727 0,727 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,190 0,060 1,250 1,263 1,263 1,263 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,280 0,050 1,320 1,333 1,333 1,333 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,970 0,070 2,040 2,060 2,060 2,060 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,070 1,760 1,778 1,778 1,778 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,070 1,760 1,778 1,778 1,778 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,970 0,050 3,020 3,050 3,050 3,050 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,060 1,710 1,727 1,727 1,727 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,360 0,060 1,420 1,434 1,434 1,434 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,070 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,060 0,760 0,768 0,768 0,768 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,860 0,060 0,920 0,929 0,929 0,929 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,050 0,630 0,636 0,636 0,636 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,040 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,030 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,160 0,080 1,240 1,252 1,252 1,252 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,080 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,130 0,050 1,180 1,192 1,192 1,192 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,580 0,040 0,620 0,626 0,626 0,626 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,140 0,050 0,200 0,220 0,240 0,260 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,300 N/A 2,300 2,530 2,760 2,990 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - _ _ _ 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - _ _ _ 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel - N/A - _ _ _ 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 1,030 N/A 1,030 1,133 1,236 1,339 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,590 N/A 2,590 2,849 3,108 3,367 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,590 N/A 2,590 2,849 3,108 3,367 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,590 N/A 2,590 2,849 3,108 3,367 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,590 N/A 2,590 2,849 3,108 3,367 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,230 N/A 3,230 3,553 3,876 4,199 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,430 N/A 3,430 3,773 4,116 4,459 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,430 N/A 3,430 3,773 4,116 4,459 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,230 N/A 3,230 3,553 3,876 4,199 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,430 N/A 3,430 3,773 4,116 4,459 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,230 N/A 3,230 3,553 3,876 4,199 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,430 N/A 3,430 3,773 4,116 4,459 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,520 N/A 3,520 3,872 4,224 4,576 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,520 N/A 3,520 3,872 4,224 4,576 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,520 N/A 3,520 3,872 4,224 4,576 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,520 N/A 3,520 3,872 4,224 4,576 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,520 N/A 3,520 3,872 4,224 4,576 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,520 N/A 3,520 3,872 4,224 4,576 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,430 N/A 3,430 3,773 4,116 4,459 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,430 N/A 3,430 3,773 4,116 4,459 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,520 N/A 3,520 3,872 4,224 4,576 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,520 N/A 3,520 3,872 4,224 4,576 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,230 N/A 3,230 3,553 3,876 4,199 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,230 N/A 3,230 3,553 3,876 4,199 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,230 N/A 3,230 3,553 3,876 4,199 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,230 N/A 3,230 3,553 3,876 4,199 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,230 N/A 3,230 3,553 3,876 4,199 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,230 N/A 3,230 3,553 3,876 4,199 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,230 N/A 3,230 3,553 3,876 4,199 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7224 90 02 Semi-finished products of tool steel 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,360 N/A 4,360 4,796 5,232 5,668 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,340 N/A 3,340 3,674 4,008 4,342 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,360 N/A 4,360 4,796 5,232 5,668 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,340 N/A 3,340 3,674 4,008 4,342 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,340 N/A 3,340 3,674 4,008 4,342 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,140 N/A 3,140 3,454 3,768 4,082 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,140 N/A 3,140 3,454 3,768 4,082 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,140 N/A 3,140 3,454 3,768 4,082 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,980 N/A 2,980 3,278 3,576 3,874 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,350 N/A 2,350 2,585 2,820 3,055 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,230 N/A 3,230 3,553 3,876 4,199 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,230 N/A 3,230 3,553 3,876 4,199 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,230 N/A 3,230 3,553 3,876 4,199 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,230 N/A 3,230 3,553 3,876 4,199 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,230 N/A 3,230 3,553 3,876 4,199 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,400 N/A 2,400 2,640 2,880 3,120 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,400 N/A 2,400 2,640 2,880 3,120 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,520 N/A 3,520 3,872 4,224 4,576 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,520 N/A 3,520 3,872 4,224 4,576 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,590 N/A 2,590 2,849 3,108 3,367 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,520 N/A 3,520 3,872 4,224 4,576 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,430 N/A 3,430 3,773 4,116 4,459 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,720 N/A 2,720 2,992 3,264 3,536 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,630 N/A 2,630 2,893 3,156 3,419 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,720 N/A 2,720 2,992 3,264 3,536 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,520 N/A 3,520 3,872 4,224 4,576 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,520 N/A 3,520 3,872 4,224 4,576 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,340 N/A 2,340 2,574 2,808 3,042 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,340 N/A 2,340 2,574 2,808 3,042 7307 19 90 Cast tube or pipe fittings of steel 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,410 N/A 2,410 2,651 2,892 3,133 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,410 N/A 2,410 2,651 2,892 3,133 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,410 N/A 2,410 2,651 2,892 3,133 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,410 N/A 2,410 2,651 2,892 3,133 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,010 N/A 3,010 3,311 3,612 3,913 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,010 N/A 3,010 3,311 3,612 3,913 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,630 N/A 2,630 2,893 3,156 3,419 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,230 N/A 3,230 3,553 3,876 4,199 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,230 N/A 3,230 3,553 3,876 4,199 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 16 Nuts of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7326 90 30 Ladders and steps, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,680 N/A 2,680 2,948 3,216 3,484 (C) Armenia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,360 0,010 1,370 1,507 1,644 1,781 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,320 0,020 1,350 1,485 1,620 1,755 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,260 0,030 1,280 1,408 1,536 1,664 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,750 0,020 2,770 2,798 2,798 2,798 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,650 0,020 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 2,220 0,020 2,250 2,273 2,273 2,273 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,010 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,010 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,040 1,510 1,525 1,525 1,525 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,040 1,480 1,495 1,495 1,495 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,030 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,420 0,030 1,460 1,475 1,475 1,475 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,680 0,030 1,710 1,727 1,727 1,727 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,590 0,040 2,620 2,646 2,646 2,646 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,220 0,040 2,250 2,273 2,273 2,273 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,220 0,040 2,250 2,273 2,273 2,273 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,300 0,030 4,330 4,373 4,373 4,373 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,170 0,030 2,200 2,222 2,222 2,222 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,620 0,030 1,650 1,667 1,667 1,667 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,660 0,040 1,700 1,717 1,717 1,717 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,820 0,030 0,850 0,859 0,859 0,859 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,040 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,740 0,030 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,020 0,530 0,535 0,535 0,535 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,020 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,490 0,040 1,540 1,555 1,555 1,555 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,060 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,460 0,030 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,750 0,020 0,770 0,778 0,778 0,778 Australia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,380 0,040 1,420 1,562 1,704 1,846 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,100 0,070 1,170 1,287 1,404 1,521 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,040 0,080 1,120 1,232 1,344 1,456 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,370 0,050 1,420 1,434 1,434 1,434 2814 10 00 Anhydrous ammonia 1,770 0,150 1,920 1,939 1,939 1,939 2814 20 00 Ammonia in aqueous solution 0,530 0,040 0,580 0,586 0,586 0,586 2834 21 00 Nitrate of potassium 1,240 0,080 1,320 1,333 1,333 1,333 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,410 0,040 0,450 0,455 0,455 0,455 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,690 0,040 0,730 0,737 0,737 0,737 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,250 0,120 1,370 1,384 1,384 1,384 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,220 0,120 1,340 1,353 1,353 1,353 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,540 0,100 0,630 0,636 0,636 0,636 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 0,910 0,110 1,020 1,030 1,030 1,030 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 0,950 0,080 1,030 1,040 1,040 1,040 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,460 0,120 1,590 1,606 1,606 1,606 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,280 0,120 1,390 1,404 1,404 1,404 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,280 0,120 1,390 1,404 1,404 1,404 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,140 0,080 2,210 2,232 2,232 2,232 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,230 0,110 1,340 1,353 1,353 1,353 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,050 0,100 1,140 1,151 1,151 1,151 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,170 0,120 1,290 1,303 1,303 1,303 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,550 0,100 0,650 0,657 0,657 0,657 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,650 0,120 0,770 0,778 0,778 0,778 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,450 0,090 0,540 0,545 0,545 0,545 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,420 0,070 0,490 0,495 0,495 0,495 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,270 0,060 0,330 0,333 0,333 0,333 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 0,880 0,150 1,030 1,040 1,040 1,040 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,500 0,120 0,620 0,626 0,626 0,626 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,090 0,930 0,939 0,939 0,939 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,440 0,060 0,500 0,505 0,505 0,505 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,070 0,020 0,090 0,099 0,108 0,117 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,790 N/A 2,790 3,069 3,348 3,627 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,970 N/A 2,970 3,267 3,564 3,861 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,970 N/A 2,970 3,267 3,564 3,861 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,970 N/A 2,970 3,267 3,564 3,861 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,970 N/A 2,970 3,267 3,564 3,861 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 3 N/A 3 3,300 3,600 3,900 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 3 N/A 3 3,300 3,600 3,900 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3 N/A 3 3,300 3,600 3,900 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,520 N/A 3,520 3,872 4,224 4,576 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,600 N/A 3,600 3,960 4,320 4,680 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,600 N/A 3,600 3,960 4,320 4,680 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,520 N/A 3,520 3,872 4,224 4,576 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,600 N/A 3,600 3,960 4,320 4,680 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,520 N/A 3,520 3,872 4,224 4,576 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,600 N/A 3,600 3,960 4,320 4,680 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,630 N/A 3,630 3,993 4,356 4,719 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,600 N/A 3,600 3,960 4,320 4,680 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,600 N/A 3,600 3,960 4,320 4,680 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,630 N/A 3,630 3,993 4,356 4,719 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,630 N/A 3,630 3,993 4,356 4,719 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,520 N/A 3,520 3,872 4,224 4,576 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,520 N/A 3,520 3,872 4,224 4,576 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,520 N/A 3,520 3,872 4,224 4,576 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,520 N/A 3,520 3,872 4,224 4,576 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,520 N/A 3,520 3,872 4,224 4,576 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,520 N/A 3,520 3,872 4,224 4,576 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,520 N/A 3,520 3,872 4,224 4,576 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7224 90 02 Semi-finished products of tool steel 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,760 N/A 4,760 5,236 5,712 6,188 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,610 N/A 3,610 3,971 4,332 4,693 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,760 N/A 4,760 5,236 5,712 6,188 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,610 N/A 3,610 3,971 4,332 4,693 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,610 N/A 3,610 3,971 4,332 4,693 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 3 N/A 3 3,300 3,600 3,900 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,320 N/A 3,320 3,652 3,984 4,316 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,790 N/A 2,790 3,069 3,348 3,627 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,520 N/A 3,520 3,872 4,224 4,576 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,520 N/A 3,520 3,872 4,224 4,576 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,520 N/A 3,520 3,872 4,224 4,576 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,520 N/A 3,520 3,872 4,224 4,576 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,520 N/A 3,520 3,872 4,224 4,576 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,830 N/A 2,830 3,113 3,396 3,679 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,830 N/A 2,830 3,113 3,396 3,679 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 3 N/A 3 3,300 3,600 3,900 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,630 N/A 3,630 3,993 4,356 4,719 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,630 N/A 3,630 3,993 4,356 4,719 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,970 N/A 2,970 3,267 3,564 3,861 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 3 N/A 3 3,300 3,600 3,900 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 3 N/A 3 3,300 3,600 3,900 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,630 N/A 3,630 3,993 4,356 4,719 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,600 N/A 3,600 3,960 4,320 4,680 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,970 N/A 2,970 3,267 3,564 3,861 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,930 N/A 2,930 3,223 3,516 3,809 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,970 N/A 2,970 3,267 3,564 3,861 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,630 N/A 3,630 3,993 4,356 4,719 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 3 N/A 3 3,300 3,600 3,900 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 3 N/A 3 3,300 3,600 3,900 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,630 N/A 3,630 3,993 4,356 4,719 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3 N/A 3 3,300 3,600 3,900 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 3 N/A 3 3,300 3,600 3,900 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,790 N/A 2,790 3,069 3,348 3,627 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,790 N/A 2,790 3,069 3,348 3,627 7307 19 90 Cast tube or pipe fittings of steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 3 N/A 3 3,300 3,600 3,900 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3 N/A 3 3,300 3,600 3,900 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3 N/A 3 3,300 3,600 3,900 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3 N/A 3 3,300 3,600 3,900 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,200 N/A 3,200 3,520 3,840 4,160 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,260 N/A 3,260 3,586 3,912 4,238 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,170 N/A 3,170 3,487 3,804 4,121 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,520 N/A 3,520 3,872 4,224 4,576 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,520 N/A 3,520 3,872 4,224 4,576 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 3 N/A 3 3,300 3,600 3,900 (C) 7318 16 Nuts of iron or steel 3,090 N/A 3,090 3,399 3,708 4,017 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 30 Ladders and steps, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 (C) 7326 90 98 Articles of iron or steel, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) Azerbaijan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,030 0,890 0,979 1,068 1,157 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,890 0,050 0,940 1,034 1,128 1,222 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,850 0,050 0,900 0,990 1,080 1,170 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,670 0,030 2,700 2,727 2,727 2,727 2814 10 00 Anhydrous ammonia 2,160 0,090 2,250 2,273 2,273 2,273 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,160 0,040 2,210 2,232 2,232 2,232 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,020 0,510 0,515 0,515 0,515 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,800 0,020 0,830 0,838 0,838 0,838 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,460 0,070 1,530 1,545 1,545 1,545 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,430 0,070 1,500 1,515 1,515 1,515 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,630 0,050 0,690 0,697 0,697 0,697 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,400 0,060 1,450 1,465 1,465 1,465 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,040 1,680 1,697 1,697 1,697 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,520 0,070 2,590 2,616 2,616 2,616 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,060 2,220 2,242 2,242 2,242 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,060 2,220 2,242 2,242 2,242 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,160 0,050 4,210 4,252 4,252 4,252 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,110 0,060 2,170 2,192 2,192 2,192 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,590 0,060 1,640 1,656 1,656 1,656 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,640 0,060 1,700 1,717 1,717 1,717 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,810 0,060 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,060 0,060 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,720 0,050 0,770 0,778 0,778 0,778 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,040 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,030 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,460 0,080 1,540 1,555 1,555 1,555 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,080 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,420 0,050 1,470 1,485 1,485 1,485 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,030 0,760 0,768 0,768 0,768 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,890 N/A 1,890 2,079 2,268 2,457 (K) 7604 10 10 Bars and rods 2,120 N/A 2,120 2,332 2,544 2,756 (K) 7604 10 90 Profiles 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7604 21 00 Hollow profiles 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7604 29 10 Bars and rods 2,120 N/A 2,120 2,332 2,544 2,756 (K) 7604 29 90 Profiles 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7605 Aluminium wire 2,120 N/A 2,120 2,332 2,544 2,756 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7608 Aluminium tubes and pipes 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7610 90 Other 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7610 90 90 Other 2,130 N/A 2,130 2,343 2,556 2,769 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,120 N/A 2,120 2,332 2,544 2,756 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,570 N/A 2,570 2,827 3,084 3,341 (K) 7616 99 10 Cast 1,890 N/A 1,890 2,079 2,268 2,457 (K) 7616 99 90 Other 2,570 N/A 2,570 2,827 3,084 3,341 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,070 0,050 0,120 0,132 0,144 0,156 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms - N/A - _ _ _ 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - _ _ _ 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - _ _ _ 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel - N/A - _ _ _ 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,500 N/A 1,500 1,650 1,800 1,950 (E) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,570 N/A 2,570 2,827 3,084 3,341 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 2,570 N/A 2,570 2,827 3,084 3,341 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 2,570 N/A 2,570 2,827 3,084 3,341 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 2,570 N/A 2,570 2,827 3,084 3,341 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 2,570 N/A 2,570 2,827 3,084 3,341 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 2,570 N/A 2,570 2,827 3,084 3,341 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 2,570 N/A 2,570 2,827 3,084 3,341 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,570 N/A 2,570 2,827 3,084 3,341 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 2,570 N/A 2,570 2,827 3,084 3,341 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 2,570 N/A 2,570 2,827 3,084 3,341 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 2,570 N/A 2,570 2,827 3,084 3,341 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,570 N/A 2,570 2,827 3,084 3,341 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 2,570 N/A 2,570 2,827 3,084 3,341 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 2,570 N/A 2,570 2,827 3,084 3,341 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 2,570 N/A 2,570 2,827 3,084 3,341 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 2,570 N/A 2,570 2,827 3,084 3,341 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 2,570 N/A 2,570 2,827 3,084 3,341 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 2,570 N/A 2,570 2,827 3,084 3,341 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 2,570 N/A 2,570 2,827 3,084 3,341 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 02 Semi-finished products of tool steel 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 3,710 N/A 3,710 4,081 4,452 4,823 (E) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 2,310 N/A 2,310 2,541 2,772 3,003 (E) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 3,710 N/A 3,710 4,081 4,452 4,823 (E) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 2,310 N/A 2,310 2,541 2,772 3,003 (E) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 2,310 N/A 2,310 2,541 2,772 3,003 (E)/(H) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (E)/(H) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (E)/(H) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 2,310 N/A 2,310 2,541 2,772 3,003 (H) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (E)/(H) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 0,190 N/A 0,190 0,209 0,228 0,247 (E) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 1,850 N/A 1,850 2,035 2,220 2,405 (E) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,500 N/A 1,500 1,650 1,800 1,950 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 2,570 N/A 2,570 2,827 3,084 3,341 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 2,570 N/A 2,570 2,827 3,084 3,341 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 2,570 N/A 2,570 2,827 3,084 3,341 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,570 N/A 2,570 2,827 3,084 3,341 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 2,570 N/A 2,570 2,827 3,084 3,341 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 0,240 N/A 0,240 0,264 0,288 0,312 (H) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 0,240 N/A 0,240 0,264 0,288 0,312 (E)/(H) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,570 N/A 2,570 2,827 3,084 3,341 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,570 N/A 2,570 2,827 3,084 3,341 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 0,240 N/A 0,240 0,264 0,288 0,312 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,570 N/A 2,570 2,827 3,084 3,341 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,570 N/A 2,570 2,827 3,084 3,341 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 0,240 N/A 0,240 0,264 0,288 0,312 (H) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 0,240 N/A 0,240 0,264 0,288 0,312 (H) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 0,240 N/A 0,240 0,264 0,288 0,312 (H) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 2,570 N/A 2,570 2,827 3,084 3,341 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,570 N/A 2,570 2,827 3,084 3,341 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,500 N/A 1,500 1,650 1,800 1,950 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,500 N/A 1,500 1,650 1,800 1,950 7307 19 90 Cast tube or pipe fittings of steel 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,360 N/A 2,360 2,596 2,832 3,068 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,360 N/A 2,360 2,596 2,832 3,068 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,360 N/A 2,360 2,596 2,832 3,068 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,360 N/A 2,360 2,596 2,832 3,068 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 1,890 N/A 1,890 2,079 2,268 2,457 (E) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 1,770 N/A 1,770 1,947 2,124 2,301 (E) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 0,240 N/A 0,240 0,264 0,288 0,312 (E) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 1,770 N/A 1,770 1,947 2,124 2,301 (E) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 2,570 N/A 2,570 2,827 3,084 3,341 (E) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 13 00 Screw hooks and screw rings, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 2,570 N/A 2,570 2,827 3,084 3,341 (E) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,140 N/A 2,140 2,354 2,568 2,782 (E) 7318 16 Nuts of iron or steel 2,220 N/A 2,220 2,442 2,664 2,886 (E) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 21 00 Spring washers and other lock washers, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,030 N/A 1,030 1,133 1,236 1,339 (E) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 0,750 N/A 0,750 0,825 0,900 0,975 (E) 7318 24 00 Cotters and cotter pins, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7318 29 00 Non-threaded articles, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7326 20 00 Articles of iron or steel wire, n.e.s. 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7326 90 30 Ladders and steps, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7326 90 50 Reels for cables, piping and the like, of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 0,140 N/A 0,140 0,154 0,168 0,182 (E) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7326 90 96 Sintered articles of iron or steel, n.e.s. 0,130 N/A 0,130 0,143 0,156 0,169 (E) 7326 90 98 Articles of iron or steel, n.e.s. 0,140 N/A 0,140 0,154 0,168 0,182 (E) Bangladesh Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,360 0,030 1,390 1,529 1,668 1,807 (A) 2523 21 00 White Portland cement 1,280 0,130 1,410 1,551 1,692 1,833 2523 29 00 Grey Portland cement 1,210 0,060 1,270 1,397 1,524 1,651 2523 90 00 White hydraulic cements 1,310 0,170 1,480 1,628 1,776 1,924 (B) 2523 90 00 Grey hydraulic cements 1,150 0,070 1,210 1,331 1,452 1,573 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,820 0,050 1,870 1,889 1,889 1,889 2814 10 00 Anhydrous ammonia 2,340 0,160 2,510 2,535 2,535 2,535 2814 20 00 Ammonia in aqueous solution 0,700 0,050 0,750 0,758 0,758 0,758 2834 21 00 Nitrate of potassium 1,640 0,080 1,720 1,737 1,737 1,737 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,520 0,040 0,560 0,566 0,566 0,566 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,860 0,040 0,910 0,919 0,919 0,919 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,570 0,120 1,700 1,717 1,717 1,717 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,540 0,120 1,660 1,677 1,677 1,677 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,090 0,770 0,778 0,778 0,778 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,100 1,280 1,293 1,293 1,293 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,250 0,080 1,320 1,333 1,333 1,333 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,920 0,120 2,040 2,060 2,060 2,060 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,660 0,110 1,770 1,788 1,788 1,788 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,660 0,110 1,770 1,788 1,788 1,788 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,830 0,080 2,920 2,949 2,949 2,949 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,610 0,110 1,710 1,727 1,727 1,727 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,360 0,100 1,450 1,465 1,465 1,465 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,500 0,110 1,620 1,636 1,636 1,636 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,090 0,800 0,808 0,808 0,808 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,110 0,950 0,960 0,960 0,960 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,080 0,650 0,657 0,657 0,657 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,070 0,620 0,626 0,626 0,626 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,350 0,050 0,400 0,404 0,404 0,404 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,140 0,130 1,270 1,283 1,283 1,283 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,630 0,110 0,740 0,747 0,747 0,747 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,080 1,190 1,202 1,202 1,202 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,570 0,060 0,630 0,636 0,636 0,636 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,690 N/A 1,690 1,859 2,028 2,197 (L) 7604 10 10 Bars and rods 1,910 N/A 1,910 2,101 2,292 2,483 (L) 7604 10 90 Profiles 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7604 21 00 Hollow profiles 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7604 29 10 Bars and rods 1,910 N/A 1,910 2,101 2,292 2,483 (L) 7604 29 90 Profiles 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7605 Aluminium wire 1,910 N/A 1,910 2,101 2,292 2,483 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7608 Aluminium tubes and pipes 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7610 90 Other 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7610 90 90 Other 1,930 N/A 1,930 2,123 2,316 2,509 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,910 N/A 1,910 2,101 2,292 2,483 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,370 N/A 2,370 2,607 2,844 3,081 (L) 7616 99 10 Cast 1,690 N/A 1,690 1,859 2,028 2,197 (L) 7616 99 90 Other 2,370 N/A 2,370 2,607 2,844 3,081 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Bahrain Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,870 N/A 1,870 2,057 2,244 2,431 (K) 7603 Aluminium powders and flakes 1,980 N/A 1,980 2,178 2,376 2,574 (K) 7604 10 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7604 10 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7604 21 00 Hollow profiles 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7604 29 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7604 29 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7605 Aluminium wire 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7608 Aluminium tubes and pipes 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 90 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7616 99 10 Cast 1,980 N/A 1,980 2,178 2,376 2,574 (K) 7616 99 90 Other 2,660 N/A 2,660 2,926 3,192 3,458 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Belarus Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,340 0,030 1,370 1,507 1,644 1,781 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,340 0,050 1,390 1,529 1,668 1,807 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,270 0,050 1,330 1,463 1,596 1,729 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,690 0,030 2,720 2,747 2,747 2,747 2814 10 00 Anhydrous ammonia 2,160 0,090 2,250 2,273 2,273 2,273 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,170 0,040 2,220 2,242 2,242 2,242 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,020 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,780 0,020 0,800 0,808 0,808 0,808 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,070 1,480 1,495 1,495 1,495 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,070 1,450 1,465 1,465 1,465 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,050 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,390 0,060 1,450 1,465 1,465 1,465 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,040 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,530 0,070 2,600 2,626 2,626 2,626 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,060 2,220 2,242 2,242 2,242 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,060 2,220 2,242 2,242 2,242 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,200 0,050 4,250 4,293 4,293 4,293 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,060 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,580 0,060 1,630 1,646 1,646 1,646 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,610 0,060 1,670 1,687 1,687 1,687 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,050 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,060 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,050 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,040 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,030 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,450 0,080 1,530 1,545 1,545 1,545 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,080 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,050 1,470 1,485 1,485 1,485 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,030 0,760 0,768 0,768 0,768 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Benin Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,860 0,040 0,900 0,990 1,080 1,170 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,920 0,070 0,990 1,089 1,188 1,287 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,880 0,070 0,960 1,056 1,152 1,248 (A) 2523 30 00 Aluminous cement - - - _ _ _ Bolivia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,030 0,900 0,990 1,080 1,170 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,870 0,060 0,930 1,023 1,116 1,209 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,830 0,060 0,890 0,979 1,068 1,157 (A) 2523 30 00 Aluminous cement - - - - - - Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7604 10 10 Bars and rods 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7604 10 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 21 00 Hollow profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 10 Bars and rods 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7604 29 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7605 Aluminium wire 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7608 Aluminium tubes and pipes 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 99 10 Cast 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7616 99 90 Other 1,150 N/A 1,150 1,265 1,380 1,495 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Bosnia and Herzegovina Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,860 0,060 0,920 1,012 1,104 1,196 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,880 0,100 0,980 1,078 1,176 1,274 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,840 0,100 0,940 1,034 1,128 1,222 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,670 0,060 2,730 2,757 2,757 2,757 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,060 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 2,160 0,090 2,260 2,283 2,283 2,283 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,050 0,540 0,545 0,545 0,545 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,050 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,150 1,620 1,636 1,636 1,636 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,150 1,590 1,606 1,606 1,606 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,110 0,750 0,758 0,758 0,758 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,400 0,130 1,520 1,535 1,535 1,535 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,100 1,740 1,757 1,757 1,757 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,520 0,150 2,670 2,697 2,697 2,697 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,140 2,300 2,323 2,323 2,323 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,140 2,300 2,323 2,323 2,323 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,160 0,100 4,260 4,303 4,303 4,303 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,110 0,130 2,240 2,262 2,262 2,262 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,590 0,120 1,710 1,727 1,727 1,727 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,640 0,140 1,780 1,798 1,798 1,798 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,810 0,120 0,920 0,929 0,929 0,929 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,060 0,140 1,200 1,212 1,212 1,212 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,720 0,110 0,820 0,828 0,828 0,828 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,080 0,590 0,596 0,596 0,596 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,070 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,460 0,170 1,630 1,646 1,646 1,646 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,130 0,720 0,727 0,727 0,727 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,420 0,100 1,530 1,545 1,545 1,545 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,070 0,800 0,808 0,808 0,808 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 3,279 N/A 3,279 3,607 3,935 4,263 (K) 7604 10 10 Bars and rods 3,059 N/A 3,059 3,365 3,671 3,977 (K) 7604 10 90 Profiles 3,059 N/A 3,059 3,365 3,671 3,977 (K) 7604 21 00 Hollow profiles 3,059 N/A 3,059 3,365 3,671 3,977 (K) 7604 29 10 Bars and rods 3,059 N/A 3,059 3,365 3,671 3,977 (K) 7604 29 90 Profiles 3,059 N/A 3,059 3,365 3,671 3,977 (K) 7605 Aluminium wire 3,703 N/A 3,703 4,073 4,443 4,813 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7608 Aluminium tubes and pipes 3,721 N/A 3,721 4,093 4,465 4,837 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 3,721 N/A 3,721 4,093 4,465 4,837 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 3,721 N/A 3,721 4,093 4,465 4,837 (K) 7610 90 Other 3,721 N/A 3,721 4,093 4,465 4,837 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 3,721 N/A 3,721 4,093 4,465 4,837 (K) 7610 90 90 Other 3,721 N/A 3,721 4,093 4,465 4,837 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 3,703 N/A 3,703 4,073 4,443 4,813 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 4,532 N/A 4,532 4,985 5,438 5,891 (K) 7616 99 10 Cast 3,279 N/A 3,279 3,607 3,935 4,263 (K) 7616 99 90 Other 4,532 N/A 4,532 4,985 5,438 5,891 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,090 0,090 0,190 0,209 0,228 0,247 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,160 N/A 2,160 2,376 2,592 2,808 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - _ _ _ 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - _ _ _ 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel - N/A - _ _ _ 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,200 N/A 2,200 2,420 2,640 2,860 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,110 N/A 3,110 3,421 3,732 4,043 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,110 N/A 3,110 3,421 3,732 4,043 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,110 N/A 3,110 3,421 3,732 4,043 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,110 N/A 3,110 3,421 3,732 4,043 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,110 N/A 3,110 3,421 3,732 4,043 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,110 N/A 3,110 3,421 3,732 4,043 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,110 N/A 3,110 3,421 3,732 4,043 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,270 N/A 3,270 3,597 3,924 4,251 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,270 N/A 3,270 3,597 3,924 4,251 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,270 N/A 3,270 3,597 3,924 4,251 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,270 N/A 3,270 3,597 3,924 4,251 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,110 N/A 3,110 3,421 3,732 4,043 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,270 N/A 3,270 3,597 3,924 4,251 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,270 N/A 3,270 3,597 3,924 4,251 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 02 Semi-finished products of tool steel 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,590 N/A 4,590 5,049 5,508 5,967 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,460 N/A 3,460 3,806 4,152 4,498 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,590 N/A 4,590 5,049 5,508 5,967 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,460 N/A 3,460 3,806 4,152 4,498 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,620 N/A 3,620 3,982 4,344 4,706 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,620 N/A 3,620 3,982 4,344 4,706 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,620 N/A 3,620 3,982 4,344 4,706 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,620 N/A 3,620 3,982 4,344 4,706 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,880 N/A 2,880 3,168 3,456 3,744 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,270 N/A 2,270 2,497 2,724 2,951 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,190 N/A 3,190 3,509 3,828 4,147 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,190 N/A 3,190 3,509 3,828 4,147 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,190 N/A 3,190 3,509 3,828 4,147 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,190 N/A 3,190 3,509 3,828 4,147 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,190 N/A 3,190 3,509 3,828 4,147 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,290 N/A 2,290 2,519 2,748 2,977 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,290 N/A 2,290 2,519 2,748 2,977 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,110 N/A 3,110 3,421 3,732 4,043 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,110 N/A 3,110 3,421 3,732 4,043 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,290 N/A 2,290 2,519 2,748 2,977 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,110 N/A 3,110 3,421 3,732 4,043 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,110 N/A 3,110 3,421 3,732 4,043 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,210 N/A 2,210 2,431 2,652 2,873 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,210 N/A 2,210 2,431 2,652 2,873 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,210 N/A 2,210 2,431 2,652 2,873 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,110 N/A 3,110 3,421 3,732 4,043 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,180 N/A 2,180 2,398 2,616 2,834 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,180 N/A 2,180 2,398 2,616 2,834 7307 19 90 Cast tube or pipe fittings of steel 2,290 N/A 2,290 2,519 2,748 2,977 7307 21 00 Flanges of stainless steel (excl. cast products) 2,860 N/A 2,860 3,146 3,432 3,718 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,860 N/A 2,860 3,146 3,432 3,718 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,860 N/A 2,860 3,146 3,432 3,718 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,860 N/A 2,860 3,146 3,432 3,718 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,850 N/A 2,850 3,135 3,420 3,705 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,020 N/A 3,020 3,322 3,624 3,926 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,080 N/A 3,080 3,388 3,696 4,004 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,170 N/A 3,170 3,487 3,804 4,121 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,170 N/A 3,170 3,487 3,804 4,121 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7318 16 Nuts of iron or steel 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7326 90 30 Ladders and steps, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,290 N/A 2,290 2,519 2,748 2,977 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,290 N/A 2,290 2,519 2,748 2,977 (C) Brazil Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ (A) 2523 10 00 White clinker - - - _ _ _ (B) 2523 10 00 Grey clinker - - - _ _ _ (A) 2523 21 00 White Portland cement 1,220 0,120 1,340 1,474 1,608 1,742 2523 29 00 Grey Portland cement - - - _ _ _ 2523 90 00 White hydraulic cements - - - _ _ _ (B) 2523 90 00 Grey hydraulic cements - - - _ _ _ (A) 2523 30 00 Aluminous cement 1,910 0,070 1,980 2,178 2,376 2,574 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,040 0,020 2,070 2,091 2,091 2,091 2814 10 00 Anhydrous ammonia 3,120 0,080 3,210 3,242 3,242 3,242 2814 20 00 Ammonia in aqueous solution 0,940 0,020 0,960 0,970 0,970 0,970 2834 21 00 Nitrate of potassium 1,930 0,040 1,960 1,980 1,980 1,980 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,670 0,020 0,690 0,697 0,697 0,697 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,110 0,020 1,130 1,141 1,141 1,141 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,020 0,060 2,070 2,091 2,091 2,091 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,970 0,050 2,030 2,050 2,050 2,050 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,890 0,040 0,930 0,939 0,939 0,939 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,440 0,040 1,480 1,495 1,495 1,495 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,470 0,030 1,500 1,515 1,515 1,515 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,260 0,050 2,310 2,333 2,333 2,333 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,040 1,990 2,010 2,010 2,010 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,040 1,990 2,010 2,010 2,010 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,190 0,040 3,230 3,262 3,262 3,262 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,040 1,940 1,959 1,959 1,959 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,650 0,040 1,690 1,707 1,707 1,707 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,860 0,050 1,910 1,929 1,929 1,929 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,870 0,040 0,910 0,919 0,919 0,919 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,990 0,040 1,030 1,040 1,040 1,040 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,030 0,710 0,717 0,717 0,717 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,730 0,030 0,750 0,758 0,758 0,758 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,020 0,480 0,485 0,485 0,485 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,050 1,390 1,404 1,404 1,404 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,820 0,070 0,900 0,909 0,909 0,909 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,030 1,340 1,353 1,353 1,353 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,680 0,020 0,700 0,707 0,707 0,707 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,820 N/A 1,820 2,002 2,184 2,366 (K) 7604 10 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 10 90 Profiles 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7604 21 00 Hollow profiles 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7604 29 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 29 90 Profiles 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7605 Aluminium wire 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,500 N/A 2,500 2,750 3 3,250 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,500 N/A 2,500 2,750 3 3,250 (K) 7608 Aluminium tubes and pipes 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7610 90 Other 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7610 90 90 Other 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,500 N/A 2,500 2,750 3 3,250 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,500 N/A 2,500 2,750 3 3,250 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,500 N/A 2,500 2,750 3 3,250 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,500 N/A 2,500 2,750 3 3,250 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,500 N/A 2,500 2,750 3 3,250 (K) 7616 99 10 Cast 1,820 N/A 1,820 2,002 2,184 2,366 (K) 7616 99 90 Other 2,500 N/A 2,500 2,750 3 3,250 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,190 0,010 0,200 0,220 0,240 0,260 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,478 N/A 1,478 1,625 1,773 1,921 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,430 N/A 1,430 1,573 1,716 1,859 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below (F) 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,480 N/A 1,480 1,628 1,776 1,924 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,480 N/A 1,480 1,628 1,776 1,924 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below (C) 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 1,620 N/A 1,620 1,782 1,944 2,106 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below (C) 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 1,620 N/A 1,620 1,782 1,944 2,106 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 1,620 N/A 1,620 1,782 1,944 2,106 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 1,620 N/A 1,620 1,782 1,944 2,106 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below (C) 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below (C) 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,940 N/A 3,940 4,334 4,728 5,122 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,210 N/A 3,210 3,531 3,852 4,173 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,940 N/A 3,940 4,334 4,728 5,122 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,940 N/A 3,940 4,334 4,728 5,122 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,320 N/A 3,320 3,652 3,984 4,316 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,320 N/A 3,320 3,652 3,984 4,316 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,320 N/A 3,320 3,652 3,984 4,316 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,320 N/A 3,320 3,652 3,984 4,316 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,320 N/A 3,320 3,652 3,984 4,316 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,320 N/A 3,320 3,652 3,984 4,316 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,320 N/A 3,320 3,652 3,984 4,316 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,320 N/A 3,320 3,652 3,984 4,316 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,340 N/A 3,340 3,674 4,008 4,342 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,340 N/A 3,340 3,674 4,008 4,342 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,340 N/A 3,340 3,674 4,008 4,342 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,340 N/A 3,340 3,674 4,008 4,342 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,940 N/A 3,940 4,334 4,728 5,122 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,340 N/A 3,340 3,674 4,008 4,342 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,370 N/A 3,370 3,707 4,044 4,381 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 4,380 N/A 4,380 4,818 5,256 5,694 (F) 7224 90 02 Semi-finished products of tool steel 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 4,380 N/A 4,380 4,818 5,256 5,694 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 4,380 N/A 4,380 4,818 5,256 5,694 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,760 N/A 4,760 5,236 5,712 6,188 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,650 N/A 3,650 4,015 4,380 4,745 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,760 N/A 4,760 5,236 5,712 6,188 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,650 N/A 3,650 4,015 4,380 4,745 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,760 N/A 3,760 4,136 4,512 4,888 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,780 N/A 3,780 4,158 4,536 4,914 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,780 N/A 3,780 4,158 4,536 4,914 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,380 N/A 4,380 4,818 5,256 5,694 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,780 N/A 3,780 4,158 4,536 4,914 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,780 N/A 3,780 4,158 4,536 4,914 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,780 N/A 3,780 4,158 4,536 4,914 (F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,380 N/A 4,380 4,818 5,256 5,694 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,780 N/A 3,780 4,158 4,536 4,914 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,780 N/A 3,780 4,158 4,536 4,914 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,780 N/A 3,780 4,158 4,536 4,914 (C)/(F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,780 N/A 3,780 4,158 4,536 4,914 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,810 N/A 3,810 4,191 4,572 4,953 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,720 N/A 2,720 2,992 3,264 3,536 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,900 N/A 2,900 3,190 3,480 3,770 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,150 N/A 3,150 3,465 3,780 4,095 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 1,670 N/A 1,670 1,837 2,004 2,171 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,150 N/A 3,150 3,465 3,780 4,095 (C) 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 1,670 N/A 1,670 1,837 2,004 2,171 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,150 N/A 3,150 3,465 3,780 4,095 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 1,670 N/A 1,670 1,837 2,004 2,171 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 1,670 N/A 1,670 1,837 2,004 2,171 (F) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 1,670 N/A 1,670 1,837 2,004 2,171 (C)/(F) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,150 N/A 3,150 3,465 3,780 4,095 (C) 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,150 N/A 3,150 3,465 3,780 4,095 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,650 N/A 1,650 1,815 1,980 2,145 (C) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,650 N/A 1,650 1,815 1,980 2,145 (C) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 1,670 N/A 1,670 1,837 2,004 2,171 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 1,730 N/A 1,730 1,903 2,076 2,249 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,320 N/A 3,320 3,652 3,984 4,316 (F) 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,320 N/A 3,320 3,652 3,984 4,316 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,740 N/A 1,740 1,914 2,088 2,262 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 1,630 N/A 1,630 1,793 1,956 2,119 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 1,740 N/A 1,740 1,914 2,088 2,262 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,320 N/A 3,320 3,652 3,984 4,316 (C) 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 (F) 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 1,830 N/A 1,830 2,013 2,196 2,379 (C) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 1,730 N/A 1,730 1,903 2,076 2,249 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 1,830 N/A 1,830 2,013 2,196 2,379 (C) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,320 N/A 3,320 3,652 3,984 4,316 (C) 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,320 N/A 3,320 3,652 3,984 4,316 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 1,740 N/A 1,740 1,914 2,088 2,262 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 1,740 N/A 1,740 1,914 2,088 2,262 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,320 N/A 2,320 2,552 2,784 3,016 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,320 N/A 2,320 2,552 2,784 3,016 7307 19 90 Cast tube or pipe fittings of steel 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,770 N/A 2,770 3,047 3,324 3,601 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,770 N/A 2,770 3,047 3,324 3,601 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,770 N/A 2,770 3,047 3,324 3,601 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,770 N/A 2,770 3,047 3,324 3,601 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 1,650 N/A 1,650 1,815 1,980 2,145 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 1,650 N/A 1,650 1,815 1,980 2,145 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 1,650 N/A 1,650 1,815 1,980 2,145 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 1,650 N/A 1,650 1,815 1,980 2,145 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,910 N/A 2,910 3,201 3,492 3,783 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,120 N/A 3,120 3,432 3,744 4,056 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3 N/A 3 3,300 3,600 3,900 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,110 N/A 3,110 3,421 3,732 4,043 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,110 N/A 3,110 3,421 3,732 4,043 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7318 16 Nuts of iron or steel 2,960 N/A 2,960 3,256 3,552 3,848 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,880 N/A 1,880 2,068 2,256 2,444 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 1,780 N/A 1,780 1,958 2,136 2,314 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 29 00 Non-threaded articles, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7326 90 30 Ladders and steps, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7326 90 98 Articles of iron or steel, n.e.s. 1,730 N/A 1,730 1,903 2,076 2,249 (C) Brunei Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker - - - _ _ _ 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,040 0,070 1,110 1,221 1,332 1,443 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Cambodia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,030 0,900 0,990 1,080 1,170 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,870 0,060 0,920 1,012 1,104 1,196 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,830 0,060 0,890 0,979 1,068 1,157 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,260 0,050 2,320 2,343 2,343 2,343 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,720 0,050 0,770 0,778 0,778 0,778 2834 21 00 Nitrate of potassium 1,940 0,070 2,020 2,040 2,040 2,040 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,870 0,040 0,910 0,919 0,919 0,919 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,440 0,040 1,480 1,495 1,495 1,495 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,610 0,120 2,730 2,757 2,757 2,757 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2,550 0,120 2,670 2,697 2,697 2,697 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,700 0,080 0,780 0,788 0,788 0,788 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,330 0,100 1,430 1,444 1,444 1,444 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,470 0,070 1,550 1,566 1,566 1,566 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,270 0,110 2,380 2,404 2,404 2,404 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,100 2,050 2,071 2,071 2,071 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,100 2,050 2,071 2,071 2,071 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,530 0,080 3,610 3,646 3,646 3,646 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,900 0,100 2 2,020 2,020 2,020 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,850 0,090 1,940 1,959 1,959 1,959 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 2,150 0,110 2,260 2,283 2,283 2,283 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,780 0,080 0,870 0,879 0,879 0,879 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,100 1,070 1,081 1,081 1,081 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,070 0,730 0,737 0,737 0,737 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,060 0,620 0,626 0,626 0,626 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,360 0,050 0,410 0,414 0,414 0,414 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,330 0,120 1,450 1,465 1,465 1,465 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,640 0,110 0,750 0,758 0,758 0,758 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,290 0,080 1,370 1,384 1,384 1,384 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,660 0,050 0,720 0,727 0,727 0,727 Cameroon Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,180 0,080 0,260 0,286 0,312 0,338 (A) 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker - - - _ _ _ 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement - - - _ _ _ 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,810 0,060 1,870 1,889 1,889 1,889 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,690 0,060 0,750 0,758 0,758 0,758 2834 21 00 Nitrate of potassium 1,630 0,080 1,710 1,727 1,727 1,727 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,520 0,040 0,560 0,566 0,566 0,566 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,850 0,040 0,900 0,909 0,909 0,909 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,550 0,130 1,680 1,697 1,697 1,697 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,520 0,130 1,650 1,667 1,667 1,667 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,670 0,080 0,750 0,758 0,758 0,758 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,170 0,090 1,260 1,273 1,273 1,273 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,240 0,070 1,310 1,323 1,323 1,323 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,900 0,110 2,010 2,030 2,030 2,030 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,100 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,100 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,820 0,100 2,920 2,949 2,949 2,949 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,100 1,690 1,707 1,707 1,707 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,090 1,440 1,454 1,454 1,454 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,110 1,600 1,616 1,616 1,616 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,070 0,770 0,778 0,778 0,778 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,830 0,080 0,910 0,919 0,919 0,919 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,060 0,620 0,626 0,626 0,626 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,540 0,060 0,600 0,606 0,606 0,606 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,040 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,130 0,100 1,230 1,242 1,242 1,242 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,620 0,100 0,720 0,727 0,727 0,727 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,070 1,170 1,182 1,182 1,182 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,040 0,610 0,616 0,616 0,616 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Canada Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,210 0,030 0,240 0,264 0,288 0,312 (A) 2523 10 00 White clinker 1,280 0,020 1,290 1,419 1,548 1,677 (B) 2523 10 00 Grey clinker - - - _ _ _ 2523 21 00 White Portland cement 1,240 0,120 1,360 1,496 1,632 1,768 2523 29 00 Grey Portland cement - - - _ _ _ 2523 90 00 White hydraulic cements 1,290 0,130 1,420 1,562 1,704 1,846 (B) 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,510 0,020 1,540 1,555 1,555 1,555 2814 10 00 Anhydrous ammonia 1,910 0,070 1,980 2 2 2 2814 20 00 Ammonia in aqueous solution 0,570 0,020 0,590 0,596 0,596 0,596 2834 21 00 Nitrate of potassium 1,360 0,030 1,400 1,414 1,414 1,414 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,020 0,460 0,465 0,465 0,465 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,720 0,020 0,740 0,747 0,747 0,747 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,310 0,060 1,370 1,384 1,384 1,384 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,280 0,060 1,340 1,353 1,353 1,353 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,040 0,610 0,616 0,616 0,616 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 0,980 0,050 1,030 1,040 1,040 1,040 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,040 0,040 1,070 1,081 1,081 1,081 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,060 1,650 1,667 1,667 1,667 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,390 0,050 1,440 1,454 1,454 1,454 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,390 0,050 1,440 1,454 1,454 1,454 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,360 0,040 2,400 2,424 2,424 2,424 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,340 0,050 1,390 1,404 1,404 1,404 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,130 0,040 1,170 1,182 1,182 1,182 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,250 0,050 1,300 1,313 1,313 1,313 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,590 0,050 0,630 0,636 0,636 0,636 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,700 0,050 0,760 0,768 0,768 0,768 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,040 0,520 0,525 0,525 0,525 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,450 0,030 0,480 0,485 0,485 0,485 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,030 0,320 0,323 0,323 0,323 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 0,950 0,070 1,020 1,030 1,030 1,030 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,530 0,070 0,600 0,606 0,606 0,606 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,920 0,040 0,960 0,970 0,970 0,970 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,480 0,030 0,500 0,505 0,505 0,505 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,960 N/A 1,960 2,156 2,352 2,548 (K) 7603 Aluminium powders and flakes 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7604 10 10 Bars and rods 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7604 10 90 Profiles 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7604 21 00 Hollow profiles 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7604 29 10 Bars and rods 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7604 29 90 Profiles 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7605 Aluminium wire 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7608 Aluminium tubes and pipes 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7610 90 Other 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7610 90 90 Other 2,310 N/A 2,310 2,541 2,772 3,003 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,750 N/A 2,750 3,025 3,300 3,575 (K) 7616 99 10 Cast 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7616 99 90 Other 2,750 N/A 2,750 3,025 3,300 3,575 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,080 0,010 0,090 0,099 0,108 0,117 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,110 N/A 1,110 1,221 1,332 1,443 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 0,760 N/A 0,760 0,836 0,912 0,988 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,290 N/A 1,290 1,419 1,548 1,677 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 1,430 N/A 1,430 1,573 1,716 1,859 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 1,430 N/A 1,430 1,573 1,716 1,859 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 1,430 N/A 1,430 1,573 1,716 1,859 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 1,430 N/A 1,430 1,573 1,716 1,859 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,050 N/A 3,050 3,355 3,660 3,965 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,210 N/A 3,210 3,531 3,852 4,173 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,050 N/A 3,050 3,355 3,660 3,965 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,050 N/A 3,050 3,355 3,660 3,965 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,210 N/A 3,210 3,531 3,852 4,173 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,290 N/A 3,290 3,619 3,948 4,277 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,210 N/A 3,210 3,531 3,852 4,173 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,290 N/A 3,290 3,619 3,948 4,277 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,290 N/A 3,290 3,619 3,948 4,277 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,050 N/A 3,050 3,355 3,660 3,965 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,050 N/A 3,050 3,355 3,660 3,965 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,050 N/A 3,050 3,355 3,660 3,965 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,050 N/A 3,050 3,355 3,660 3,965 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,050 N/A 3,050 3,355 3,660 3,965 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,050 N/A 3,050 3,355 3,660 3,965 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,050 N/A 3,050 3,355 3,660 3,965 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7224 90 02 Semi-finished products of tool steel 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,700 N/A 4,700 5,170 5,640 6,110 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,700 N/A 4,700 5,170 5,640 6,110 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,660 N/A 3,660 4,026 4,392 4,758 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,600 N/A 2,600 2,860 3,120 3,380 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,590 N/A 1,590 1,749 1,908 2,067 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,050 N/A 3,050 3,355 3,660 3,965 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 1,340 N/A 1,340 1,474 1,608 1,742 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,050 N/A 3,050 3,355 3,660 3,965 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 1,340 N/A 1,340 1,474 1,608 1,742 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,050 N/A 3,050 3,355 3,660 3,965 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 1,340 N/A 1,340 1,474 1,608 1,742 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 1,340 N/A 1,340 1,474 1,608 1,742 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 1,340 N/A 1,340 1,474 1,608 1,742 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,050 N/A 3,050 3,355 3,660 3,965 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,050 N/A 3,050 3,355 3,660 3,965 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,340 N/A 1,340 1,474 1,608 1,742 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,340 N/A 1,340 1,474 1,608 1,742 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 1,340 N/A 1,340 1,474 1,608 1,742 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,290 N/A 3,290 3,619 3,948 4,277 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,290 N/A 3,290 3,619 3,948 4,277 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 1,440 N/A 1,440 1,584 1,728 1,872 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,290 N/A 3,290 3,619 3,948 4,277 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 1,580 N/A 1,580 1,738 1,896 2,054 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 1,510 N/A 1,510 1,661 1,812 1,963 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 1,580 N/A 1,580 1,738 1,896 2,054 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,290 N/A 3,290 3,619 3,948 4,277 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,290 N/A 3,290 3,619 3,948 4,277 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 1,510 N/A 1,510 1,661 1,812 1,963 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,110 N/A 1,110 1,221 1,332 1,443 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,110 N/A 1,110 1,221 1,332 1,443 7307 19 90 Cast tube or pipe fittings of steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,660 N/A 2,660 2,926 3,192 3,458 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,660 N/A 2,660 2,926 3,192 3,458 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,660 N/A 2,660 2,926 3,192 3,458 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,660 N/A 2,660 2,926 3,192 3,458 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,910 N/A 2,910 3,201 3,492 3,783 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,180 N/A 3,180 3,498 3,816 4,134 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 1,520 N/A 1,520 1,672 1,824 1,976 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,010 N/A 3,010 3,311 3,612 3,913 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,050 N/A 3,050 3,355 3,660 3,965 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,050 N/A 3,050 3,355 3,660 3,965 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,480 N/A 2,480 2,728 2,976 3,224 (C) 7318 16 Nuts of iron or steel 2,910 N/A 2,910 3,201 3,492 3,783 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 1,610 N/A 1,610 1,771 1,932 2,093 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7318 29 00 Non-threaded articles, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 30 Ladders and steps, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 98 Articles of iron or steel, n.e.s. 1,510 N/A 1,510 1,661 1,812 1,963 (C) Chile Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,050 0,920 1,012 1,104 1,196 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,940 0,070 1,010 1,111 1,212 1,313 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,900 0,070 0,970 1,067 1,164 1,261 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,850 0,060 1,900 1,919 1,919 1,919 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,050 0,730 0,737 0,737 0,737 2834 21 00 Nitrate of potassium 1,640 0,080 1,730 1,747 1,747 1,747 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,040 0,550 0,556 0,556 0,556 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,040 0,880 0,889 0,889 0,889 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,140 1,660 1,677 1,677 1,677 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,130 1,630 1,646 1,646 1,646 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,100 0,760 0,768 0,768 0,768 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,170 0,110 1,280 1,293 1,293 1,293 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,250 0,090 1,340 1,353 1,353 1,353 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,920 0,130 2,060 2,081 2,081 2,081 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,660 0,120 1,780 1,798 1,798 1,798 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,660 0,120 1,780 1,798 1,798 1,798 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,880 0,090 2,970 3 3 3 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,610 0,120 1,730 1,747 1,747 1,747 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,100 1,450 1,465 1,465 1,465 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,480 0,120 1,600 1,616 1,616 1,616 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,100 0,800 0,808 0,808 0,808 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,120 0,960 0,970 0,970 0,970 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,090 0,660 0,667 0,667 0,667 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,070 0,600 0,606 0,606 0,606 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,060 0,400 0,404 0,404 0,404 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,140 0,150 1,290 1,303 1,303 1,303 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,120 0,730 0,737 0,737 0,737 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,090 1,200 1,212 1,212 1,212 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,570 0,060 0,630 0,636 0,636 0,636 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7604 10 10 Bars and rods 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7604 10 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 21 00 Hollow profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 10 Bars and rods 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7604 29 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7605 Aluminium wire 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7608 Aluminium tubes and pipes 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 99 10 Cast 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7616 99 90 Other 1,150 N/A 1,150 1,265 1,380 1,495 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,060 0,030 0,100 0,110 0,120 0,130 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,960 N/A 1,960 2,156 2,352 2,548 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel - N/A - _ _ _ 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,970 N/A 1,970 2,167 2,364 2,561 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,950 N/A 2,950 3,245 3,540 3,835 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 2,950 N/A 2,950 3,245 3,540 3,835 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 2,950 N/A 2,950 3,245 3,540 3,835 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 2,950 N/A 2,950 3,245 3,540 3,835 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 2,950 N/A 2,950 3,245 3,540 3,835 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 2,950 N/A 2,950 3,245 3,540 3,835 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 2,950 N/A 2,950 3,245 3,540 3,835 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,950 N/A 2,950 3,245 3,540 3,835 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 2,950 N/A 2,950 3,245 3,540 3,835 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 2,950 N/A 2,950 3,245 3,540 3,835 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 2,950 N/A 2,950 3,245 3,540 3,835 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,950 N/A 2,950 3,245 3,540 3,835 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 2,950 N/A 2,950 3,245 3,540 3,835 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 2,950 N/A 2,950 3,245 3,540 3,835 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 2,950 N/A 2,950 3,245 3,540 3,835 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 2,950 N/A 2,950 3,245 3,540 3,835 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 2,950 N/A 2,950 3,245 3,540 3,835 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 2,950 N/A 2,950 3,245 3,540 3,835 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 2,950 N/A 2,950 3,245 3,540 3,835 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 02 Semi-finished products of tool steel 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 3,780 N/A 3,780 4,158 4,536 4,914 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 2,850 N/A 2,850 3,135 3,420 3,705 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 3,780 N/A 3,780 4,158 4,536 4,914 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 2,850 N/A 2,850 3,135 3,420 3,705 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 2,850 N/A 2,850 3,135 3,420 3,705 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 2,850 N/A 2,850 3,135 3,420 3,705 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 2,850 N/A 2,850 3,135 3,420 3,705 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,960 N/A 1,960 2,156 2,352 2,548 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 2,950 N/A 2,950 3,245 3,540 3,835 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 2,950 N/A 2,950 3,245 3,540 3,835 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 2,950 N/A 2,950 3,245 3,540 3,835 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,950 N/A 2,950 3,245 3,540 3,835 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 2,950 N/A 2,950 3,245 3,540 3,835 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,990 N/A 1,990 2,189 2,388 2,587 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,990 N/A 1,990 2,189 2,388 2,587 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,950 N/A 2,950 _ 3,540 3,835 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,950 N/A 2,950 3,245 3,540 3,835 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,050 N/A 2,050 2,255 2,460 2,665 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,950 N/A 2,950 3,245 3,540 3,835 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,950 N/A 2,950 3,245 3,540 3,835 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,020 N/A 2,020 2,222 2,424 2,626 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,020 N/A 2,020 2,222 2,424 2,626 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,020 N/A 2,020 2,222 2,424 2,626 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 2,950 N/A 2,950 3,245 3,540 3,835 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,950 N/A 2,950 3,245 3,540 3,835 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,960 N/A 1,960 2,156 2,352 2,548 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,960 N/A 1,960 2,156 2,352 2,548 7307 19 90 Cast tube or pipe fittings of steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,310 N/A 2,310 2,541 2,772 3,003 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,310 N/A 2,310 2,541 2,772 3,003 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,310 N/A 2,310 2,541 2,772 3,003 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,310 N/A 2,310 2,541 2,772 3,003 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,540 N/A 2,540 2,794 3,048 3,302 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,540 N/A 2,540 2,794 3,048 3,302 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 2,950 N/A 2,950 3,245 3,540 3,835 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 2,950 N/A 2,950 3,245 3,540 3,835 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,170 N/A 2,170 2,387 2,604 2,821 (C) 7318 16 Nuts of iron or steel 2,170 N/A 2,170 2,387 2,604 2,821 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,180 N/A 2,180 2,398 2,616 2,834 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 30 Ladders and steps, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,050 N/A 2,050 2,255 2,460 2,665 (C) China Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,210 0,110 0,320 0,352 0,384 0,416 (A) 2523 10 00 White clinker 1,240 0,060 1,300 1,430 1,560 1,690 (B) 2523 10 00 Grey clinker 1,350 0,040 1,390 1,529 1,668 1,807 (A) 2523 21 00 White Portland cement 1,250 0,140 1,390 1,529 1,668 1,807 2523 29 00 Grey Portland cement 1,350 0,070 1,420 1,562 1,704 1,846 2523 90 00 White hydraulic cements 1,290 0,180 1,460 1,606 1,752 1,898 (B) 2523 90 00 Grey hydraulic cements 1,280 0,080 1,360 1,496 1,632 1,768 (A) 2523 30 00 Aluminous cement 1,980 0,200 2,180 2,398 2,616 2,834 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 3,020 0,060 3,080 3,111 3,111 3,111 2814 10 00 Anhydrous ammonia 4,170 0,190 4,360 4,404 4,404 4,404 2814 20 00 Ammonia in aqueous solution 1,250 0,060 1,310 1,323 1,323 1,323 2834 21 00 Nitrate of potassium 2,770 0,090 2,850 2,879 2,879 2,879 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,900 0,050 0,940 0,949 0,949 0,949 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,490 0,050 1,540 1,555 1,555 1,555 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,700 0,140 2,850 2,879 2,879 2,879 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2,640 0,140 2,780 2,808 2,808 2,808 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,190 0,100 1,290 1,303 1,303 1,303 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 2,010 0,120 2,130 2,151 2,151 2,151 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 2,100 0,090 2,190 2,212 2,212 2,212 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,230 0,140 3,370 3,404 3,404 3,404 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,780 0,130 2,900 2,929 2,929 2,929 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,780 0,130 2,900 2,929 2,929 2,929 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,720 0,100 4,810 4,858 4,858 4,858 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,710 0,120 2,830 2,858 2,858 2,858 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 2,300 0,110 2,410 2,434 2,434 2,434 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 2,560 0,130 2,690 2,717 2,717 2,717 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 1,200 0,100 1,310 1,323 1,323 1,323 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,410 0,120 1,530 1,545 1,545 1,545 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,960 0,090 1,050 1,061 1,061 1,061 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,080 1,040 1,050 1,050 1,050 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,060 0,670 0,677 0,677 0,677 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,920 0,150 2,070 2,091 2,091 2,091 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 1,100 0,140 1,240 1,252 1,252 1,252 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,860 0,100 1,960 1,980 1,980 1,980 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,960 0,060 1,020 1,030 1,030 1,030 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 3 N/A 3 3,300 3,600 3,900 (K) 7603 Aluminium powders and flakes 4,148 N/A 4,148 4,563 4,978 5,392 (K) 7604 10 10 Bars and rods 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7604 10 90 Profiles 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7604 21 00 Hollow profiles 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7604 29 10 Bars and rods 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7604 29 90 Profiles 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7605 Aluminium wire 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 4,120 N/A 4,120 4,532 4,944 5,356 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 5,559 N/A 5,559 6,115 6,671 7,227 (K) 7608 Aluminium tubes and pipes 4,896 N/A 4,896 5,385 5,875 6,364 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 4,896 N/A 4,896 5,385 5,875 6,364 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 4,896 N/A 4,896 5,385 5,875 6,364 (K) 7610 90 Other 4,896 N/A 4,896 5,385 5,875 6,364 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 4,896 N/A 4,896 5,385 5,875 6,364 (K) 7610 90 90 Other 4,896 N/A 4,896 5,385 5,875 6,364 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 5,559 N/A 5,559 6,115 6,671 7,227 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 5,559 N/A 5,559 6,115 6,671 7,227 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 5,559 N/A 5,559 6,115 6,671 7,227 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 4,881 N/A 4,881 5,369 5,857 6,345 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 5,559 N/A 5,559 6,115 6,671 7,227 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 5,559 N/A 5,559 6,115 6,671 7,227 (K) 7616 99 10 Cast 4,542 N/A 4,542 4,996 5,450 5,904 (K) 7616 99 90 Other 5,559 N/A 5,559 6,115 6,671 7,227 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 26,640 N/A 26,640 29,304 31,968 34,632 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,200 0,060 0,260 0,286 0,312 0,338 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,660 N/A 1,660 1,826 1,992 2,158 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon 5,590 N/A 5,590 6,149 6,708 7,267 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon 2,870 N/A 2,870 3,157 3,444 3,731 7202 60 00 Ferro-nickel 6,150 N/A 6,150 6,765 7,380 7,995 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,802 N/A 2,802 3,082 3,362 3,643 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,740 N/A 1,740 1,914 2,088 2,262 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 3,187 N/A 3,187 3,506 3,824 4,143 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 3,205 N/A 3,205 3,526 3,846 4,167 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3,205 N/A 3,205 3,526 3,846 4,167 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 3,187 N/A 3,187 3,506 3,824 4,143 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 3,187 N/A 3,187 3,506 3,824 4,143 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 3,187 N/A 3,187 3,506 3,824 4,143 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 3,205 N/A 3,205 3,526 3,846 4,167 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 3,205 N/A 3,205 3,526 3,846 4,167 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 3,205 N/A 3,205 3,526 3,846 4,167 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3,205 N/A 3,205 3,526 3,846 4,167 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 3,314 N/A 3,314 3,645 3,976 4,308 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 3,169 N/A 3,169 3,486 3,803 4,119 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 5,650 N/A 5,650 6,215 6,780 7,345 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 5,580 N/A 5,580 6,138 6,696 7,254 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 5,580 N/A 5,580 6,138 6,696 7,254 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 5,650 N/A 5,650 6,215 6,780 7,345 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 5,580 N/A 5,580 6,138 6,696 7,254 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 5,650 N/A 5,650 6,215 6,780 7,345 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 5,580 N/A 5,580 6,138 6,696 7,254 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 5,590 N/A 5,590 6,149 6,708 7,267 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 5,590 N/A 5,590 6,149 6,708 7,267 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 5,590 N/A 5,590 6,149 6,708 7,267 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 5,590 N/A 5,590 6,149 6,708 7,267 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 5,590 N/A 5,590 6,149 6,708 7,267 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 5,590 N/A 5,590 6,149 6,708 7,267 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 5,580 N/A 5,580 6,138 6,696 7,254 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 5,580 N/A 5,580 6,138 6,696 7,254 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 5,590 N/A 5,590 6,149 6,708 7,267 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 5,590 N/A 5,590 6,149 6,708 7,267 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 5,590 N/A 5,590 6,149 6,708 7,267 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 5,590 N/A 5,590 6,149 6,708 7,267 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 5,590 N/A 5,590 6,149 6,708 7,267 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 5,590 N/A 5,590 6,149 6,708 7,267 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 5,650 N/A 5,650 6,215 6,780 7,345 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 5,590 N/A 5,590 6,149 6,708 7,267 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 5,590 N/A 5,590 6,149 6,708 7,267 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 6,180 N/A 6,180 6,798 7,416 8,034 (F) 7224 90 02 Semi-finished products of tool steel 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 6,180 N/A 6,180 6,798 7,416 8,034 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 6,180 N/A 6,180 6,798 7,416 8,034 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 8,090 N/A 8,090 8,899 9,708 10,517 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 6,110 N/A 6,110 6,721 7,332 7,943 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 8,090 N/A 8,090 8,899 9,708 10,517 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 6,110 N/A 6,110 6,721 7,332 7,943 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 6,110 N/A 6,110 6,721 7,332 7,943 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 6,120 N/A 6,120 6,732 7,344 7,956 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,180 N/A 6,180 6,798 7,416 8,034 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,120 N/A 6,120 6,732 7,344 7,956 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,180 N/A 6,180 6,798 7,416 8,034 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,120 N/A 6,120 6,732 7,344 7,956 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 6,120 N/A 6,120 6,732 7,344 7,956 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 6,120 N/A 6,120 6,732 7,344 7,956 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,275 N/A 2,275 2,502 2,730 2,957 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 6,205 N/A 6,205 6,826 7,446 8,067 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,191 N/A 2,191 2,410 2,629 2,848 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 7,005 N/A 7,005 7,706 8,406 9,107 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 7,005 N/A 7,005 7,706 8,406 9,107 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 7,005 N/A 7,005 7,706 8,406 9,107 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 7,005 N/A 7,005 7,706 8,406 9,107 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 7,005 N/A 7,005 7,706 8,406 9,107 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,680 N/A 2,680 2,948 3,216 3,484 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,680 N/A 2,680 2,948 3,216 3,484 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,585 N/A 2,585 2,844 3,102 3,361 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 7,025 N/A 7,025 7,728 8,430 9,133 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 7,025 N/A 7,025 7,728 8,430 9,133 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 3,565 N/A 3,565 3,922 4,278 4,635 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 7,025 N/A 7,025 7,728 8,430 9,133 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 7,015 N/A 7,015 7,717 8,418 9,120 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 3,565 N/A 3,565 3,922 4,278 4,635 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 3,565 N/A 3,565 3,922 4,278 4,635 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 3,565 N/A 3,565 3,922 4,278 4,635 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 7,025 N/A 7,025 7,728 8,430 9,133 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 7,025 N/A 7,025 7,728 8,430 9,133 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 3,565 N/A 3,565 3,922 4,278 4,635 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,252 N/A 3,252 3,577 3,902 4,228 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,252 N/A 3,252 3,577 3,902 4,228 7307 19 90 Cast tube or pipe fittings of steel 3,252 N/A 3,252 3,577 3,902 4,228 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 5,035 N/A 5,035 5,539 6,042 6,546 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 5,035 N/A 5,035 5,539 6,042 6,546 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 5,035 N/A 5,035 5,539 6,042 6,546 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 5,035 N/A 5,035 5,539 6,042 6,546 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 3,252 N/A 3,252 3,577 3,902 4,228 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 3,252 N/A 3,252 3,577 3,902 4,228 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 3,252 N/A 3,252 3,577 3,902 4,228 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 3,252 N/A 3,252 3,577 3,902 4,228 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 6,035 N/A 6,035 6,639 7,242 7,846 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 6,655 N/A 6,655 7,321 7,986 8,652 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 4,312 N/A 4,312 4,743 5,174 5,605 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 6,645 N/A 6,645 7,310 7,974 8,639 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 7,005 N/A 7,005 7,706 8,406 9,107 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 7,005 N/A 7,005 7,706 8,406 9,107 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 6,375 N/A 6,375 7,013 7,650 8,288 (C) 7318 16 Nuts of iron or steel 5,045 N/A 5,045 5,550 6,054 6,559 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 4,555 N/A 4,555 5,011 5,466 5,922 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,738 N/A 2,738 3,012 3,286 3,559 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 30 Ladders and steps, of iron or steel 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 3,076 N/A 3,076 3,384 3,691 3,999 (C) 7326 90 98 Articles of iron or steel, n.e.s. 3,076 N/A 3,076 3,384 3,691 3,999 (C) Colombia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,090 0,020 1,110 1,221 1,332 1,443 (A) 2523 21 00 White Portland cement 1,210 0,120 1,330 1,463 1,596 1,729 2523 29 00 Grey Portland cement 1,090 0,030 1,120 1,232 1,344 1,456 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,900 0,020 1,930 1,949 1,949 1,949 2814 10 00 Anhydrous ammonia 2,260 0,080 2,340 2,363 2,363 2,363 2814 20 00 Ammonia in aqueous solution 0,680 0,020 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 1,680 0,030 1,720 1,737 1,737 1,737 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,020 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,020 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,050 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,050 1,550 1,566 1,566 1,566 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,040 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,190 0,040 1,230 1,242 1,242 1,242 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,280 0,030 1,310 1,323 1,323 1,323 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,970 0,050 2,020 2,040 2,040 2,040 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,040 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,040 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,970 0,040 3,010 3,040 3,040 3,040 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,040 1,690 1,707 1,707 1,707 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,360 0,040 1,400 1,414 1,414 1,414 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,050 1,540 1,555 1,555 1,555 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,040 0,740 0,747 0,747 0,747 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,850 0,040 0,900 0,909 0,909 0,909 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,030 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,030 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,020 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,160 0,050 1,220 1,232 1,232 1,232 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,070 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,130 0,030 1,160 1,172 1,172 1,172 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,580 0,020 0,600 0,606 0,606 0,606 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,030 N/A 1,030 1,133 1,236 1,339 (L) 7604 10 10 Bars and rods 1,250 N/A 1,250 1,375 1,500 1,625 (L) 7604 10 90 Profiles 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7604 21 00 Hollow profiles 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7604 29 10 Bars and rods 1,250 N/A 1,250 1,375 1,500 1,625 (L) 7604 29 90 Profiles 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7605 Aluminium wire 1,250 N/A 1,250 1,375 1,500 1,625 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7608 Aluminium tubes and pipes 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7610 90 Other 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7610 90 90 Other 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,250 N/A 1,250 1,375 1,500 1,625 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,710 N/A 1,710 1,881 2,052 2,223 (L) 7616 99 10 Cast 1,030 N/A 1,030 1,133 1,236 1,339 (L) 7616 99 90 Other 1,710 N/A 1,710 1,881 2,052 2,223 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,300 0,010 0,310 0,341 0,372 0,403 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,930 N/A 1,930 2,123 2,316 2,509 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,020 N/A 2,020 2,222 2,424 2,626 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,070 N/A 3,070 3,377 3,684 3,991 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,820 N/A 3,820 4,202 4,584 4,966 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,820 N/A 3,820 4,202 4,584 4,966 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,070 N/A 3,070 3,377 3,684 3,991 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,820 N/A 3,820 4,202 4,584 4,966 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,070 N/A 3,070 3,377 3,684 3,991 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,820 N/A 3,820 4,202 4,584 4,966 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 4,150 N/A 4,150 4,565 4,980 5,395 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 4,150 N/A 4,150 4,565 4,980 5,395 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 4,150 N/A 4,150 4,565 4,980 5,395 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 4,150 N/A 4,150 4,565 4,980 5,395 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 4,150 N/A 4,150 4,565 4,980 5,395 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 4,150 N/A 4,150 4,565 4,980 5,395 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,820 N/A 3,820 4,202 4,584 4,966 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,820 N/A 3,820 4,202 4,584 4,966 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 4,150 N/A 4,150 4,565 4,980 5,395 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 4,150 N/A 4,150 4,565 4,980 5,395 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,080 N/A 3,080 3,388 3,696 4,004 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,080 N/A 3,080 3,388 3,696 4,004 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,080 N/A 3,080 3,388 3,696 4,004 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,080 N/A 3,080 3,388 3,696 4,004 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,070 N/A 3,070 3,377 3,684 3,991 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,080 N/A 3,080 3,388 3,696 4,004 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,080 N/A 3,080 3,388 3,696 4,004 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7224 90 02 Semi-finished products of tool steel 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 5,300 N/A 5,300 5,830 6,360 6,890 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 4,180 N/A 4,180 4,598 5,016 5,434 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 5,300 N/A 5,300 5,830 6,360 6,890 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 4,180 N/A 4,180 4,598 5,016 5,434 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 4,180 N/A 4,180 4,598 5,016 5,434 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 4,520 N/A 4,520 4,972 5,424 5,876 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,430 N/A 3,430 3,773 4,116 4,459 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,730 N/A 2,730 3,003 3,276 3,549 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,950 N/A 1,950 2,145 2,340 2,535 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,080 N/A 3,080 3,388 3,696 4,004 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,080 N/A 3,080 3,388 3,696 4,004 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,080 N/A 3,080 3,388 3,696 4,004 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,080 N/A 3,080 3,388 3,696 4,004 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,080 N/A 3,080 3,388 3,696 4,004 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,050 N/A 2,050 2,255 2,460 2,665 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,050 N/A 2,050 2,255 2,460 2,665 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,150 N/A 4,150 4,565 4,980 5,395 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,150 N/A 4,150 4,565 4,980 5,395 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,560 N/A 2,560 2,816 3,072 3,328 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,150 N/A 4,150 4,565 4,980 5,395 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,820 N/A 3,820 4,202 4,584 4,966 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 3,120 N/A 3,120 3,432 3,744 4,056 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,790 N/A 2,790 3,069 3,348 3,627 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 3,120 N/A 3,120 3,432 3,744 4,056 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 4,150 N/A 4,150 4,565 4,980 5,395 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,150 N/A 4,150 4,565 4,980 5,395 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,940 N/A 1,940 2,134 2,328 2,522 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,940 N/A 1,940 2,134 2,328 2,522 7307 19 90 Cast tube or pipe fittings of steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,730 N/A 2,730 3,003 3,276 3,549 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,730 N/A 2,730 3,003 3,276 3,549 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,730 N/A 2,730 3,003 3,276 3,549 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,730 N/A 2,730 3,003 3,276 3,549 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,580 N/A 3,580 3,938 4,296 4,654 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,760 N/A 3,760 4,136 4,512 4,888 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,890 N/A 2,890 3,179 3,468 3,757 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,990 N/A 2,990 3,289 3,588 3,887 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,080 N/A 3,080 3,388 3,696 4,004 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,080 N/A 3,080 3,388 3,696 4,004 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,680 N/A 2,680 2,948 3,216 3,484 (C) 7318 16 Nuts of iron or steel 2,950 N/A 2,950 3,245 3,540 3,835 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,210 N/A 2,210 2,431 2,652 2,873 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,160 N/A 2,160 2,376 2,592 2,808 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7326 90 30 Ladders and steps, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,890 N/A 2,890 3,179 3,468 3,757 (C) Congo Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,850 0,040 0,890 0,979 1,068 1,157 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,850 0,070 0,930 1,023 1,116 1,209 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,820 0,070 0,890 0,979 1,068 1,157 (A) 2523 30 00 Aluminous cement - - - _ _ _ Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N.A. 10,820 11,902 12,984 14,066 Costa Rica Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,850 0 0,850 0,935 1,020 1,105 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,850 0 0,860 0,946 1,032 1,118 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,810 0,010 0,820 0,902 0,984 1,066 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,820 0,030 1,850 1,869 1,869 1,869 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,030 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 1,630 0,050 1,670 1,687 1,687 1,687 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,030 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,030 0,870 0,879 0,879 0,879 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,080 1,610 1,626 1,626 1,626 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,080 1,570 1,586 1,586 1,586 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,060 0,720 0,727 0,727 0,727 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,060 1,230 1,242 1,242 1,242 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,240 0,050 1,290 1,303 1,303 1,303 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,900 0,070 1,980 2 2 2 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,070 1,710 1,727 1,727 1,727 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,070 1,710 1,727 1,727 1,727 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,840 0,050 2,890 2,919 2,919 2,919 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,060 1,660 1,677 1,677 1,677 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,060 1,400 1,414 1,414 1,414 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,070 1,550 1,566 1,566 1,566 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,060 0,750 0,758 0,758 0,758 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,830 0,070 0,900 0,909 0,909 0,909 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,050 0,620 0,626 0,626 0,626 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,040 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,030 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,130 0,080 1,210 1,222 1,222 1,222 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,080 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,050 1,150 1,162 1,162 1,162 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,040 0,600 0,606 0,606 0,606 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,410 N/A 1,410 1,551 1,692 1,833 (L) 7604 10 10 Bars and rods 1,630 N/A 1,630 1,793 1,956 2,119 (L) 7604 10 90 Profiles 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7604 21 00 Hollow profiles 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7604 29 10 Bars and rods 1,630 N/A 1,630 1,793 1,956 2,119 (L) 7604 29 90 Profiles 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7605 Aluminium wire 1,630 N/A 1,630 1,793 1,956 2,119 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7608 Aluminium tubes and pipes 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7610 90 Other 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7610 90 90 Other 1,650 N/A 1,650 1,815 1,980 2,145 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,630 N/A 1,630 1,793 1,956 2,119 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,090 N/A 2,090 2,299 2,508 2,717 (L) 7616 99 10 Cast 1,410 N/A 1,410 1,551 1,692 1,833 (L) 7616 99 90 Other 2,090 N/A 2,090 2,299 2,508 2,717 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Côte d'Ivoire Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker - - - _ _ _ 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,130 0,050 1,180 1,298 1,416 1,534 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,760 0,050 1,800 1,818 1,818 1,818 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,670 0,040 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 1,580 0,060 1,640 1,656 1,656 1,656 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,500 0,030 0,540 0,545 0,545 0,545 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,830 0,030 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,510 0,100 1,610 1,626 1,626 1,626 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,480 0,100 1,580 1,596 1,596 1,596 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,650 0,070 0,720 0,727 0,727 0,727 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,140 0,080 1,210 1,222 1,222 1,222 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,200 0,060 1,260 1,273 1,273 1,273 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,850 0,090 1,940 1,959 1,959 1,959 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,080 1,680 1,697 1,697 1,697 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,080 1,680 1,697 1,697 1,697 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,740 0,070 2,810 2,838 2,838 2,838 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,550 0,080 1,630 1,646 1,646 1,646 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,300 0,080 1,380 1,394 1,394 1,394 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,440 0,090 1,540 1,555 1,555 1,555 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,680 0,070 0,750 0,758 0,758 0,758 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,810 0,080 0,890 0,899 0,899 0,899 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,060 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,050 0,580 0,586 0,586 0,586 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,330 0,040 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,100 0,100 1,200 1,212 1,212 1,212 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,600 0,090 0,700 0,707 0,707 0,707 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,060 0,060 1,130 1,141 1,141 1,141 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,550 0,040 0,590 0,596 0,596 0,596 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Cuba Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker 1,320 0,070 1,400 1,540 1,680 1,820 (B) 2523 10 00 Grey clinker 1,090 0,050 1,140 1,254 1,368 1,482 (A) 2523 21 00 White Portland cement 1,320 0,160 1,480 1,628 1,776 1,924 2523 29 00 Grey Portland cement 1,090 0,090 1,180 1,298 1,416 1,534 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,820 0,060 1,880 1,899 1,899 1,899 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,060 0,740 0,747 0,747 0,747 2834 21 00 Nitrate of potassium 1,620 0,090 1,710 1,727 1,727 1,727 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,050 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,050 0,850 0,859 0,859 0,859 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,460 0,140 1,600 1,616 1,616 1,616 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,430 0,140 1,570 1,586 1,586 1,586 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,650 0,100 0,750 0,758 0,758 0,758 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,150 0,120 1,260 1,273 1,273 1,273 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,090 1,320 1,333 1,333 1,333 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,140 2,030 2,050 2,050 2,050 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,120 1,750 1,768 1,768 1,768 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,120 1,750 1,768 1,768 1,768 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,840 0,090 2,940 2,969 2,969 2,969 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,120 1,710 1,727 1,727 1,727 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,310 0,110 1,420 1,434 1,434 1,434 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,430 0,130 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,680 0,100 0,790 0,798 0,798 0,798 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,120 0,940 0,949 0,949 0,949 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,090 0,650 0,657 0,657 0,657 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,080 0,600 0,606 0,606 0,606 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,330 0,060 0,400 0,404 0,404 0,404 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,110 0,150 1,270 1,283 1,283 1,283 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,600 0,120 0,720 0,727 0,727 0,727 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,090 1,180 1,192 1,192 1,192 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,060 0,620 0,626 0,626 0,626 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Curaçao Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Democratic Republic of the Congo Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,240 0 1,250 1,375 1,500 1,625 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,240 0,010 1,250 1,375 1,500 1,625 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Dominican Republic Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,030 0,050 1,070 1,177 1,284 1,391 (A) 2523 21 00 White Portland cement 1,210 0,150 1,360 1,496 1,632 1,768 2523 29 00 Grey Portland cement 1,040 0,080 1,120 1,232 1,344 1,456 2523 90 00 White hydraulic cements 1,260 0,190 1,450 1,595 1,740 1,885 (B) 2523 90 00 Grey hydraulic cements 0,990 0,080 1,070 1,177 1,284 1,391 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,050 1,850 1,869 1,869 1,869 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,050 0,730 0,737 0,737 0,737 2834 21 00 Nitrate of potassium 1,610 0,080 1,690 1,707 1,707 1,707 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,040 0,550 0,556 0,556 0,556 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,040 0,880 0,889 0,889 0,889 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,120 1,650 1,667 1,667 1,667 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,120 1,620 1,636 1,636 1,636 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,090 0,750 0,758 0,758 0,758 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,100 1,260 1,273 1,273 1,273 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,080 1,300 1,313 1,313 1,313 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,880 0,120 2 2,020 2,020 2,020 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,110 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,110 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,800 0,080 2,880 2,909 2,909 2,909 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,580 0,110 1,690 1,707 1,707 1,707 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,330 0,100 1,420 1,434 1,434 1,434 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,110 1,580 1,596 1,596 1,596 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,090 0,780 0,788 0,788 0,788 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,110 0,930 0,939 0,939 0,939 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,080 0,640 0,646 0,646 0,646 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,070 0,600 0,606 0,606 0,606 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,050 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,120 0,140 1,260 1,273 1,273 1,273 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,110 0,720 0,727 0,727 0,727 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,080 1,170 1,182 1,182 1,182 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,060 0,620 0,626 0,626 0,626 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 N/A Ecuador Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,090 0,010 1,110 1,221 1,332 1,443 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,090 0,020 1,110 1,221 1,332 1,443 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,040 0,030 1,070 1,177 1,284 1,391 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,880 0,020 1,910 1,929 1,929 1,929 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,020 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 1,670 0,040 1,700 1,717 1,717 1,717 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,020 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,020 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,060 1,590 1,606 1,606 1,606 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,060 1,560 1,576 1,576 1,576 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,050 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,060 1,240 1,252 1,252 1,252 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,270 0,040 1,310 1,323 1,323 1,323 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,060 2,010 2,030 2,030 2,030 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,680 0,060 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,680 0,060 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,940 0,040 2,980 3,010 3,010 3,010 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,060 1,690 1,707 1,707 1,707 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,360 0,050 1,410 1,424 1,424 1,424 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,060 1,550 1,566 1,566 1,566 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,050 0,750 0,758 0,758 0,758 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,850 0,060 0,910 0,919 0,919 0,919 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,050 0,620 0,626 0,626 0,626 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,040 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,030 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,160 0,080 1,230 1,242 1,242 1,242 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,080 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,120 0,040 1,160 1,172 1,172 1,172 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,580 0,030 0,610 0,616 0,616 0,616 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7604 10 10 Bars and rods 2,190 N/A 2,190 2,409 2,628 2,847 (L) 7604 10 90 Profiles 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7604 21 00 Hollow profiles 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7604 29 10 Bars and rods 2,190 N/A 2,190 2,409 2,628 2,847 (L) 7604 29 90 Profiles 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7605 Aluminium wire 2,190 N/A 2,190 2,409 2,628 2,847 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7608 Aluminium tubes and pipes 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7610 90 Other 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7610 90 90 Other 2,210 N/A 2,210 2,431 2,652 2,873 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,190 N/A 2,190 2,409 2,628 2,847 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,650 N/A 2,650 2,915 3,180 3,445 (L) 7616 99 10 Cast 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7616 99 90 Other 2,650 N/A 2,650 2,915 3,180 3,445 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/a 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 Egypt Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker 1,290 0,040 1,330 1,463 1,596 1,729 (B) 2523 10 00 Grey clinker 1,240 0,030 1,270 1,397 1,524 1,651 (A) 2523 21 00 White Portland cement 1,250 0,130 1,390 1,529 1,668 1,807 2523 29 00 Grey Portland cement 1,240 0,050 1,290 1,419 1,548 1,677 2523 90 00 White hydraulic cements 1,300 0,160 1,450 1,595 1,740 1,885 (B) 2523 90 00 Grey hydraulic cements 1,180 0,060 1,240 1,364 1,488 1,612 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,460 0,030 2,490 2,515 2,515 2,515 2814 10 00 Anhydrous ammonia 1,960 0,100 2,050 2,071 2,071 2,071 2814 20 00 Ammonia in aqueous solution 0,590 0,030 0,620 0,626 0,626 0,626 2834 21 00 Nitrate of potassium 1,990 0,050 2,040 2,060 2,060 2,060 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,020 0,460 0,465 0,465 0,465 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,720 0,020 0,750 0,758 0,758 0,758 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,320 0,080 1,390 1,404 1,404 1,404 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,290 0,070 1,360 1,374 1,374 1,374 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,060 0,630 0,636 0,636 0,636 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,060 1,340 1,353 1,353 1,353 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,510 0,050 1,560 1,576 1,576 1,576 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,320 0,080 2,390 2,414 2,414 2,414 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,070 2,050 2,071 2,071 2,071 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,070 2,050 2,071 2,071 2,071 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,840 0,050 3,890 3,929 3,929 3,929 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,070 2,010 2,030 2,030 2,030 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,450 0,060 1,510 1,525 1,525 1,525 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,070 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,060 0,800 0,808 0,808 0,808 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,070 1,040 1,050 1,050 1,050 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,050 0,710 0,717 0,717 0,717 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,040 0,500 0,505 0,505 0,505 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,040 0,330 0,333 0,333 0,333 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,090 1,430 1,444 1,444 1,444 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,530 0,080 0,620 0,626 0,626 0,626 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,050 1,360 1,374 1,374 1,374 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,040 0,710 0,717 0,717 0,717 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,870 N/A 1,870 2,057 2,244 2,431 (K) 7603 Aluminium powders and flakes 2,698 N/A 2,698 2,967 3,237 3,507 (K) 7604 10 10 Bars and rods 2,997 N/A 2,997 3,297 3,597 3,896 (K) 7604 10 90 Profiles 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7604 21 00 Hollow profiles 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7604 29 10 Bars and rods 2,997 N/A 2,997 3,297 3,597 3,896 (K) 7604 29 90 Profiles 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7605 Aluminium wire 2,997 N/A 2,997 3,297 3,597 3,896 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7608 Aluminium tubes and pipes 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7610 90 Other 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7610 90 90 Other 3,025 N/A 3,025 3,327 3,629 3,932 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,997 N/A 2,997 3,297 3,597 3,896 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 3,624 N/A 3,624 3,986 4,349 4,711 (K) 7616 99 10 Cast 2,698 N/A 2,698 2,967 3,237 3,507 (K) 7616 99 90 Other 3,624 N/A 3,624 3,986 4,349 4,711 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 El Salvador Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,040 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,870 0,070 0,940 1,034 1,128 1,222 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,830 0,080 0,910 1,001 1,092 1,183 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,820 0,050 1,870 1,889 1,889 1,889 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,040 0,730 0,737 0,737 0,737 2834 21 00 Nitrate of potassium 1,620 0,070 1,690 1,707 1,707 1,707 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,040 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,800 0,040 0,840 0,848 0,848 0,848 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,460 0,120 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,430 0,110 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,650 0,080 0,730 0,737 0,737 0,737 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,150 0,090 1,240 1,252 1,252 1,252 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,070 1,300 1,313 1,313 1,313 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,110 2 2,020 2,020 2,020 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,100 1,720 1,737 1,737 1,737 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,100 1,720 1,737 1,737 1,737 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,850 0,080 2,920 2,949 2,949 2,949 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,100 1,680 1,697 1,697 1,697 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,310 0,090 1,400 1,414 1,414 1,414 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,430 0,100 1,540 1,555 1,555 1,555 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,680 0,080 0,770 0,778 0,778 0,778 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,100 0,920 0,929 0,929 0,929 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,080 0,630 0,636 0,636 0,636 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,060 0,590 0,596 0,596 0,596 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,330 0,050 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,110 0,120 1,240 1,252 1,252 1,252 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,600 0,100 0,700 0,707 0,707 0,707 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,080 1,160 1,172 1,172 1,172 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,050 0,610 0,616 0,616 0,616 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,980 N/A 1,980 2,178 2,376 2,574 (L) 7604 10 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7604 10 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7604 21 00 Hollow profiles 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7604 29 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7604 29 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7605 Aluminium wire 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7608 Aluminium tubes and pipes 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 90 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7616 99 10 Cast 1,980 N/A 1,980 2,178 2,376 2,574 (L) 7616 99 90 Other 2,660 N/A 2,660 2,926 3,192 3,458 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Equatorial Guinea Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N.A. 10,820 11,902 12,984 14,066 Eritrea Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,850 0,060 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,850 0,110 0,960 1,056 1,152 1,248 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Eswatini Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ (A) 2523 10 00 White clinker - - - _ _ _ (B) 2523 10 00 Grey clinker - - - _ _ _ (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,170 0,080 1,250 1,375 1,500 1,625 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,120 0,080 1,200 1,320 1,440 1,560 (A) 2523 30 00 Aluminous cement - - - _ _ _ Ethiopia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,850 0 0,850 0,935 1,020 1,105 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,850 0 0,850 0,935 1,020 1,105 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,830 0,050 1,880 1,899 1,899 1,899 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,830 0,050 0,880 0,889 0,889 0,889 2834 21 00 Nitrate of potassium 1,720 0,070 1,800 1,818 1,818 1,818 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,600 0,040 0,640 0,646 0,646 0,646 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1 0,040 1,030 1,040 1,040 1,040 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,810 0,120 1,930 1,949 1,949 1,949 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,770 0,120 1,890 1,909 1,909 1,909 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,790 0,070 0,860 0,869 0,869 0,869 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,080 1,370 1,384 1,384 1,384 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,310 0,060 1,380 1,394 1,394 1,394 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,020 0,100 2,120 2,141 2,141 2,141 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,740 0,090 1,830 1,848 1,848 1,848 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,740 0,090 1,830 1,848 1,848 1,848 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,860 0,080 2,940 2,969 2,969 2,969 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,690 0,090 1,780 1,798 1,798 1,798 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,480 0,080 1,560 1,576 1,576 1,576 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,670 0,100 1,770 1,788 1,788 1,788 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,770 0,070 0,840 0,848 0,848 0,848 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,890 0,080 0,970 0,980 0,980 0,980 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,060 0,660 0,667 0,667 0,667 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,060 0,700 0,707 0,707 0,707 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,400 0,040 0,450 0,455 0,455 0,455 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,200 0,100 1,300 1,313 1,313 1,313 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,720 0,100 0,820 0,828 0,828 0,828 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,170 0,070 1,230 1,242 1,242 1,242 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,600 0,040 0,640 0,646 0,646 0,646 Gabon Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,24 0,04 1,28 1,408 1,536 1,664 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,13 0,06 1,19 1,309 1,428 1,547 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,07 0,06 1,14 1,254 1,368 1,482 (A) 2523 30 00 Aluminous cement - - - _ _ _ Georgia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,360 0,010 1,360 1,496 1,632 1,768 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,190 0,020 1,200 1,320 1,440 1,560 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,780 0,010 2,780 2,808 2,808 2,808 2814 10 00 Anhydrous ammonia 2,160 0,030 2,190 2,212 2,212 2,212 2814 20 00 Ammonia in aqueous solution 0,650 0,010 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 2,240 0,020 2,250 2,273 2,273 2,273 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,010 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,010 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,030 1,500 1,515 1,515 1,515 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,030 1,470 1,485 1,485 1,485 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,040 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,430 0,040 1,470 1,485 1,485 1,485 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,690 0,030 1,720 1,737 1,737 1,737 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,600 0,040 2,640 2,666 2,666 2,666 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,230 0,040 2,270 2,293 2,293 2,293 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,230 0,040 2,270 2,293 2,293 2,293 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,330 0,010 4,340 4,383 4,383 4,383 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,180 0,040 2,220 2,242 2,242 2,242 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,630 0,030 1,660 1,677 1,677 1,677 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,660 0,040 1,700 1,717 1,717 1,717 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,820 0,040 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,050 1,140 1,151 1,151 1,151 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,740 0,040 0,780 0,788 0,788 0,788 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,020 0,530 0,535 0,535 0,535 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,020 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,500 0,060 1,570 1,586 1,586 1,586 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,060 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,030 1,500 1,515 1,515 1,515 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,750 0,030 0,780 0,788 0,788 0,788 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Ghana Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,180 0,100 0,280 0,308 0,336 0,364 (A) 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,850 0,030 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,050 0,050 1,100 1,210 1,320 1,430 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1 0,050 1,060 1,166 1,272 1,378 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,050 1,850 1,869 1,869 1,869 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,700 0,040 0,750 0,758 0,758 0,758 2834 21 00 Nitrate of potassium 1,630 0,060 1,690 1,707 1,707 1,707 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,190 0,030 1,220 1,232 1,232 1,232 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,970 0,030 2 2,020 2,020 2,020 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 3,570 0,100 3,680 3,717 3,717 3,717 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 3,500 0,100 3,600 3,636 3,636 3,636 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,060 0,750 0,758 0,758 0,758 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,080 1,250 1,263 1,263 1,263 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,240 0,060 1,300 1,313 1,313 1,313 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,910 0,090 2 2,020 2,020 2,020 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,080 1,730 1,747 1,747 1,747 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,080 1,730 1,747 1,747 1,747 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,810 0,070 2,890 2,919 2,919 2,919 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,080 1,680 1,697 1,697 1,697 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 2 0,080 2,080 2,101 2,101 2,101 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 2,530 0,090 2,620 2,646 2,646 2,646 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,060 0,770 0,778 0,778 0,778 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,070 0,910 0,919 0,919 0,919 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,050 0,620 0,626 0,626 0,626 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,050 0,600 0,606 0,606 0,606 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,350 0,040 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,130 0,090 1,220 1,232 1,232 1,232 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,630 0,090 0,720 0,727 0,727 0,727 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,060 1,160 1,172 1,172 1,172 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,570 0,040 0,610 0,616 0,616 0,616 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Guatemala Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,070 0,940 1,034 1,128 1,222 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,870 0,110 0,980 1,078 1,176 1,274 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,830 0,120 0,950 1,045 1,140 1,235 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,820 0,080 1,890 1,909 1,909 1,909 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,070 0,750 0,758 0,758 0,758 2834 21 00 Nitrate of potassium 1,620 0,110 1,730 1,747 1,747 1,747 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,060 0,570 0,576 0,576 0,576 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,060 0,900 0,909 0,909 0,909 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,180 1,710 1,727 1,727 1,727 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,180 1,670 1,687 1,687 1,687 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,130 0,790 0,798 0,798 0,798 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,150 1,310 1,323 1,323 1,323 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,240 0,110 1,350 1,364 1,364 1,364 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,900 0,170 2,070 2,091 2,091 2,091 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,160 1,800 1,818 1,818 1,818 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,160 1,800 1,818 1,818 1,818 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,830 0,120 2,950 2,980 2,980 2,980 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,150 1,740 1,757 1,757 1,757 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,330 0,140 1,470 1,485 1,485 1,485 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,160 1,640 1,656 1,656 1,656 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,130 0,820 0,828 0,828 0,828 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,830 0,160 0,990 1 1 1 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,120 0,680 0,687 0,687 0,687 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,100 0,630 0,636 0,636 0,636 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,080 0,420 0,424 0,424 0,424 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,130 0,200 1,320 1,333 1,333 1,333 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,150 0,760 0,768 0,768 0,768 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,120 1,210 1,222 1,222 1,222 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,080 0,650 0,657 0,657 0,657 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,980 N/A 1,980 2,178 2,376 2,574 (L) 7604 10 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7604 10 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7604 21 00 Hollow profiles 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7604 29 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7604 29 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7605 Aluminium wire 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7608 Aluminium tubes and pipes 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7610 90 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,200 N/A 2,200 2,420 2,640 2,860 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7616 99 10 Cast 1,980 N/A 1,980 2,178 2,376 2,574 (L) 7616 99 90 Other 2,660 N/A 2,660 2,926 3,192 3,458 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Haiti Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 1,090 0,060 1,160 1,276 1,392 1,508 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 1,110 0,100 1,200 1,320 1,440 1,560 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 1,050 0,100 1,150 1,265 1,380 1,495 (A) 2523 30 00 Aluminous cement - - - _ _ _ Honduras Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,040 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,880 0,070 0,940 1,034 1,128 1,222 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,840 0,070 0,910 1,001 1,092 1,183 (A) 2523 30 00 Aluminous cement - - - _ _ _ Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,040 1,850 1,869 1,869 1,869 2814 10 00 Anhydrous ammonia - - - _ _ _ 2814 20 00 Ammonia in aqueous solution 0,680 0,040 0,720 0,727 0,727 0,727 2834 21 00 Nitrate of potassium 1,620 0,060 1,680 1,697 1,697 1,697 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,500 0,040 1,540 1,555 1,555 1,555 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 2,490 0,040 2,530 2,555 2,555 2,555 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 4,530 0,110 4,640 4,686 4,686 4,686 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 4,430 0,100 4,530 4,575 4,575 4,575 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,080 0,740 0,747 0,747 0,747 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,090 1,250 1,263 1,263 1,263 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,070 1,300 1,313 1,313 1,313 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,100 1,990 2,010 2,010 2,010 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,100 1,730 1,747 1,747 1,747 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,100 1,730 1,747 1,747 1,747 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,810 0,070 2,880 2,909 2,909 2,909 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,090 1,680 1,697 1,697 1,697 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 2,310 0,080 2,390 2,414 2,414 2,414 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 3,010 0,100 3,110 3,141 3,141 3,141 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,080 0,770 0,778 0,778 0,778 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,830 0,090 0,920 0,929 0,929 0,929 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,070 0,630 0,636 0,636 0,636 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,060 0,590 0,596 0,596 0,596 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,050 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,120 0,120 1,240 1,252 1,252 1,252 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,100 0,710 0,717 0,717 0,717 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,070 1,160 1,172 1,172 1,172 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,050 0,610 0,616 0,616 0,616 Hong Kong Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker - - - _ _ _ 2523 10 00 Grey clinker 0,870 0,050 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - _ _ _ 2523 29 00 Grey Portland cement 0,900 0,080 0,980 1,078 1,176 1,274 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements 0,860 0,080 0,940 1,034 1,128 1,222 (A) 2523 30 00 Aluminous cement - - - _ _ _ India Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - _ _ _ 2523 10 00 White clinker 1,350 0,070 1,410 1,551 1,692 1,833 (B) 2523 10 00 Grey clinker 1,390 0,050 1,440 1,584 1,728 1,872 (A) 2523 21 00 White Portland cement 1,330 0,140 1,470 1,617 1,764 1,911 2523 29 00 Grey Portland cement 1,390 0,090 1,480 1,628 1,776 1,924 2523 90 00 White hydraulic cements - - - _ _ _ 2523 90 00 Grey hydraulic cements - - - _ _ _ 2523 30 00 Aluminous cement 2,050 0,240 2,290 2,519 2,748 2,977 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,940 0,070 2,010 2,030 2,030 2,030 2814 10 00 Anhydrous ammonia 3,060 0,220 3,280 3,313 3,313 3,313 2814 20 00 Ammonia in aqueous solution 0,920 0,070 0,990 1 1 1 2834 21 00 Nitrate of potassium 1,860 0,100 1,960 1,980 1,980 1,980 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,680 0,060 0,740 0,747 0,747 0,747 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,130 0,060 1,180 1,192 1,192 1,192 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,050 0,170 2,220 2,242 2,242 2,242 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2 0,160 2,170 2,192 2,192 2,192 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,890 0,120 1,010 1,020 1,020 1,020 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,410 0,140 1,550 1,566 1,566 1,566 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,420 0,110 1,520 1,535 1,535 1,535 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,180 0,160 2,340 2,363 2,363 2,363 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,150 2,040 2,060 2,060 2,060 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,150 2,040 2,060 2,060 2,060 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,030 0,110 3,140 3,171 3,171 3,171 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,830 0,140 1,970 1,990 1,990 1,990 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,620 0,130 1,750 1,768 1,768 1,768 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,850 0,150 2,010 2,030 2,030 2,030 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,850 0,120 0,980 0,990 0,990 0,990 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,150 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,110 0,770 0,778 0,778 0,778 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,720 0,090 0,810 0,818 0,818 0,818 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,450 0,070 0,530 0,535 0,535 0,535 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,310 0,180 1,490 1,505 1,505 1,505 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,820 0,150 0,970 0,980 0,980 0,980 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,270 0,110 1,380 1,394 1,394 1,394 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,660 0,080 0,730 0,737 0,737 0,737 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,870 N/A 1,870 2,057 2,244 2,431 (K) 7603 Aluminium powders and flakes 3,071 N/A 3,071 3,378 3,686 3,993 (K) 7604 10 10 Bars and rods 3,413 N/A 3,413 3,754 4,095 4,436 (K) 7604 10 90 Profiles 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7604 21 00 Hollow profiles 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7604 29 10 Bars and rods 3,413 N/A 3,413 3,754 4,095 4,436 (K) 7604 29 90 Profiles 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7605 Aluminium wire 2,594 N/A 2,594 2,853 3,113 3,372 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7608 Aluminium tubes and pipes 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7610 90 Other 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7610 90 90 Other 3,444 N/A 3,444 3,788 4,132 4,477 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 3,413 N/A 3,413 3,754 4,095 4,436 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 4,126 N/A 4,126 4,539 4,951 5,364 (K) 7616 99 10 Cast 3,071 N/A 3,071 3,378 3,686 3,993 (K) 7616 99 90 Other 4,126 N/A 4,126 4,539 4,951 5,364 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,290 0,050 0,340 0,374 0,408 0,442 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,530 N/A 2,530 2,783 3,036 3,289 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon 5,590 N/A 5,590 6,149 6,708 7,267 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 4,200 N/A 4,200 4,620 5,040 5,460 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,540 N/A 2,540 2,794 3,048 3,302 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,640 N/A 2,640 2,904 3,168 3,432 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,640 N/A 2,640 2,904 3,168 3,432 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 6,530 N/A 6,530 7,183 7,836 8,489 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 6,490 N/A 6,490 7,139 7,788 8,437 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 6,490 N/A 6,490 7,139 7,788 8,437 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 6,530 N/A 6,530 7,183 7,836 8,489 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 6,490 N/A 6,490 7,139 7,788 8,437 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 6,530 N/A 6,530 7,183 7,836 8,489 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 6,490 N/A 6,490 7,139 7,788 8,437 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 6,500 N/A 6,500 7,150 7,800 8,450 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 6,500 N/A 6,500 7,150 7,800 8,450 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 6,500 N/A 6,500 7,150 7,800 8,450 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 6,500 N/A 6,500 7,150 7,800 8,450 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 6,500 N/A 6,500 7,150 7,800 8,450 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 6,500 N/A 6,500 7,150 7,800 8,450 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 6,490 N/A 6,490 7,139 7,788 8,437 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 6,490 N/A 6,490 7,139 7,788 8,437 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 6,500 N/A 6,500 7,150 7,800 8,450 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 6,500 N/A 6,500 7,150 7,800 8,450 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 6,480 N/A 6,480 7,128 7,776 8,424 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 6,480 N/A 6,480 7,128 7,776 8,424 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 6,480 N/A 6,480 7,128 7,776 8,424 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 6,480 N/A 6,480 7,128 7,776 8,424 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 6,530 N/A 6,530 7,183 7,836 8,489 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 6,480 N/A 6,480 7,128 7,776 8,424 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 6,480 N/A 6,480 7,128 7,776 8,424 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 7,350 N/A 7,350 8,085 8,820 9,555 (F) 7224 90 02 Semi-finished products of tool steel 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 7,350 N/A 7,350 8,085 8,820 9,555 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 7,350 N/A 7,350 8,085 8,820 9,555 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 8,580 N/A 8,580 9,438 10,296 11,154 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 7,320 N/A 7,320 8,052 8,784 9,516 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 8,580 N/A 8,580 9,438 10,296 11,154 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 7,320 N/A 7,320 8,052 8,784 9,516 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 7,320 N/A 7,320 8,052 8,784 9,516 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 7,300 N/A 7,300 8,030 8,760 9,490 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,300 N/A 7,300 8,030 8,760 9,490 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,350 N/A 7,350 8,085 8,820 9,555 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,300 N/A 7,300 8,030 8,760 9,490 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,300 N/A 7,300 8,030 8,760 9,490 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,300 N/A 7,300 8,030 8,760 9,490 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,350 N/A 7,350 8,085 8,820 9,555 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,300 N/A 7,300 8,030 8,760 9,490 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 7,300 N/A 7,300 8,030 8,760 9,490 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 7,300 N/A 7,300 8,030 8,760 9,490 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 7,300 N/A 7,300 8,030 8,760 9,490 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 7,300 N/A 7,300 8,030 8,760 9,490 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 4,300 N/A 4,300 4,730 5,160 5,590 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 5,450 N/A 5,450 5,995 6,540 7,085 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,840 N/A 2,840 3,124 3,408 3,692 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 6,490 N/A 6,490 7,139 7,788 8,437 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 6,490 N/A 6,490 7,139 7,788 8,437 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 6,490 N/A 6,490 7,139 7,788 8,437 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 6,490 N/A 6,490 7,139 7,788 8,437 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 6,490 N/A 6,490 7,139 7,788 8,437 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 4,320 N/A 4,320 4,752 5,184 5,616 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 4,320 N/A 4,320 4,752 5,184 5,616 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 6,500 N/A 6,500 7,150 7,800 8,450 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 6,500 N/A 6,500 7,150 7,800 8,450 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 4,320 N/A 4,320 4,752 5,184 5,616 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 6,500 N/A 6,500 7,150 7,800 8,450 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 6,490 N/A 6,490 7,139 7,788 8,437 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 4,330 N/A 4,330 4,763 5,196 5,629 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 4,320 N/A 4,320 4,752 5,184 5,616 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 4,330 N/A 4,330 4,763 5,196 5,629 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 6,500 N/A 6,500 7,150 7,800 8,450 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 6,500 N/A 6,500 7,150 7,800 8,450 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,859 N/A 3,859 4,245 4,631 5,017 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,859 N/A 3,859 4,245 4,631 5,017 7307 19 90 Cast tube or pipe fittings of steel 4,320 N/A 4,320 4,752 5,184 5,616 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 4,810 N/A 4,810 5,291 5,772 6,253 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 4,810 N/A 4,810 5,291 5,772 6,253 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 4,810 N/A 4,810 5,291 5,772 6,253 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 4,810 N/A 4,810 5,291 5,772 6,253 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 5,930 N/A 5,930 6,523 7,116 7,709 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 6,650 N/A 6,650 7,315 7,980 8,645 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 4,310 N/A 4,310 4,741 5,172 5,603 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 6,640 N/A 6,640 7,304 7,968 8,632 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 5,770 N/A 5,770 6,347 6,924 7,501 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 5,770 N/A 5,770 6,347 6,924 7,501 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 5,720 N/A 5,720 6,292 6,864 7,436 (C) 7318 16 Nuts of iron or steel 5,140 N/A 5,140 5,654 6,168 6,682 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 5,140 N/A 5,140 5,654 6,168 6,682 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 4,280 N/A 4,280 4,708 5,136 5,564 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7318 29 00 Non-threaded articles, of iron or steel 4,270 N/A 4,270 4,697 5,124 5,551 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 30 Ladders and steps, of iron or steel 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 4,910 N/A 4,910 5,401 5,892 6,383 (C) 7326 90 98 Articles of iron or steel, n.e.s. 4,910 N/A 4,910 5,401 5,892 6,383 (C) Indonesia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,060 0,070 2,130 2,151 2,151 2,151 2814 10 00 Anhydrous ammonia 2,050 0,230 2,280 2,303 2,303 2,303 2814 20 00 Ammonia in aqueous solution 0,620 0,070 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 1,740 0,110 1,860 1,879 1,879 1,879 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,060 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,060 0,830 0,838 0,838 0,838 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,400 0,180 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,370 0,180 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,140 0,740 0,747 0,747 0,747 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,150 1,330 1,343 1,343 1,343 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,320 0,120 1,440 1,454 1,454 1,454 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,040 0,180 2,220 2,242 2,242 2,242 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,760 0,160 1,920 1,939 1,939 1,939 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,760 0,160 1,920 1,939 1,939 1,939 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,220 0,120 3,330 3,363 3,363 3,363 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,710 0,160 1,870 1,889 1,889 1,889 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,350 0,140 1,490 1,505 1,505 1,505 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,440 0,170 1,610 1,626 1,626 1,626 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,140 0,830 0,838 0,838 0,838 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,870 0,160 1,040 1,050 1,050 1,050 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,130 0,720 0,727 0,727 0,727 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,100 0,580 0,586 0,586 0,586 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,080 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,200 0,200 1,400 1,414 1,414 1,414 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,150 0,710 0,717 0,717 0,717 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,160 0,120 1,280 1,293 1,293 1,293 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,600 0,090 0,680 0,687 0,687 0,687 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,830 N/A 1,830 2,013 2,196 2,379 (K) 7604 10 10 Bars and rods 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7604 10 90 Profiles 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7604 21 00 Hollow profiles 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7604 29 10 Bars and rods 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7604 29 90 Profiles 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7605 Aluminium wire 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7608 Aluminium tubes and pipes 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7610 90 Other 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7610 90 90 Other 2,070 N/A 2,070 2,277 2,484 2,691 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,060 N/A 2,060 2,266 2,472 2,678 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7616 99 10 Cast 1,830 N/A 1,830 2,013 2,196 2,379 (K) 7616 99 90 Other 2,510 N/A 2,510 2,761 3,012 3,263 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) - - - - - - 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 7,920 N/A 7,920 8,712 9,504 10,296 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - _ _ _ 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ _ 7202 60 00 Ferro-nickel 6,150 N/A 6,150 6,765 7,380 7,995 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 7,900 N/A 7,900 8,690 9,480 10,270 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 8,630 N/A 8,630 9,493 10,356 11,219 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 8,630 N/A 8,630 9,493 10,356 11,219 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 8,630 N/A 8,630 9,493 10,356 11,219 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 8,690 N/A 8,690 9,559 10,428 11,297 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 8,670 N/A 8,670 9,537 10,404 11,271 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 8,670 N/A 8,670 9,537 10,404 11,271 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 8,690 N/A 8,690 9,559 10,428 11,297 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 8,690 N/A 8,690 9,559 10,428 11,297 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 8,690 N/A 8,690 9,559 10,428 11,297 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 8,690 N/A 8,690 9,559 10,428 11,297 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 8,690 N/A 8,690 9,559 10,428 11,297 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 8,690 N/A 8,690 9,559 10,428 11,297 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 8,630 N/A 8,630 9,493 10,356 11,219 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 8,690 N/A 8,690 9,559 10,428 11,297 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 8,690 N/A 8,690 9,559 10,428 11,297 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 9,960 N/A 9,960 10,956 11,952 12,948 (F) 7224 90 02 Semi-finished products of tool steel 10 N/A 10 11 12 13 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 10 N/A 10 11 12 13 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 10 N/A 10 11 12 13 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 10 N/A 10 11 12 13 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 10 N/A 10 11 12 13 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 9,960 N/A 9,960 10,956 11,952 12,948 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 10 N/A 10 11 12 13 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 10 N/A 10 11 12 13 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 9,960 N/A 9,960 10,956 11,952 12,948 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 13,240 N/A 13,240 14,564 15,888 17,212 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 10 N/A 10 11 12 13 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 10 N/A 10 11 12 13 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 10 N/A 10 11 12 13 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 13,240 N/A 13,240 14,564 15,888 17,212 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 10 N/A 10 11 12 13 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 10 N/A 10 11 12 13 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 10 N/A 10 11 12 13 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 10,020 N/A 10,020 11,022 12,024 13,026 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 9,960 N/A 9,960 10,956 11,952 12,948 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 10,020 N/A 10,020 11,022 12,024 13,026 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 9,960 N/A 9,960 10,956 11,952 12,948 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 10,020 N/A 10,020 11,022 12,024 13,026 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 10,020 N/A 10,020 11,022 12,024 13,026 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 10,020 N/A 10,020 11,022 12,024 13,026 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 7,890 N/A 7,890 8,679 9,468 10,257 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below _ _ _ 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 8,630 N/A 8,630 9,493 10,356 11,219 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 8,630 N/A 8,630 9,493 10,356 11,219 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 8,630 N/A 8,630 9,493 10,356 11,219 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 8,630 N/A 8,630 9,493 10,356 11,219 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 8,630 N/A 8,630 9,493 10,356 11,219 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 7,860 N/A 7,860 8,646 9,432 10,218 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 7,860 N/A 7,860 8,646 9,432 10,218 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 8,690 N/A 8,690 9,559 10,428 11,297 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 8,690 N/A 8,690 9,559 10,428 11,297 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 8,230 N/A 8,230 9,053 9,876 10,699 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 8,690 N/A 8,690 9,559 10,428 11,297 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 8,670 N/A 8,670 9,537 10,404 11,271 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 7,960 N/A 7,960 8,756 9,552 10,348 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 7,940 N/A 7,940 8,734 9,528 10,322 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 7,960 N/A 7,960 8,756 9,552 10,348 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 8,690 N/A 8,690 9,559 10,428 11,297 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 8,690 N/A 8,690 9,559 10,428 11,297 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 7,890 N/A 7,890 8,679 9,468 10,257 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 7,890 N/A 7,890 8,679 9,468 10,257 7307 19 90 Cast tube or pipe fittings of steel 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 7,940 N/A 7,940 8,734 9,528 10,322 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 7,940 N/A 7,940 8,734 9,528 10,322 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 7,940 N/A 7,940 8,734 9,528 10,322 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 7,940 N/A 7,940 8,734 9,528 10,322 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 10,010 N/A 10,010 11,011 12,012 13,013 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 8,250 N/A 8,250 9,075 9,900 10,725 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 9,980 N/A 9,980 10,978 11,976 12,974 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 8,650 N/A 8,650 9,515 10,380 11,245 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 8,650 N/A 8,650 9,515 10,380 11,245 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 16 Nuts of iron or steel 8,540 N/A 8,540 9,394 10,248 11,102 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 8,540 N/A 8,540 9,394 10,248 11,102 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7318 29 00 Non-threaded articles, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7326 90 30 Ladders and steps, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 8,230 N/A 8,230 9,053 9,876 10,699 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 8,210 N/A 8,210 9,031 9,852 10,673 (C) 7326 90 98 Articles of iron or steel, n.e.s. 8,250 N/A 8,250 9,075 9,900 10,725 (C) Iran Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,320 0,050 1,380 1,518 1,656 1,794 (B) 2523 10 00 Grey clinker - - - - - - 2523 21 00 White Portland cement 1,320 0,140 1,460 1,606 1,752 1,898 2523 29 00 Grey Portland cement - - - - - - 2523 90 00 White hydraulic cements 1,350 0,180 1,530 1,683 1,836 1,989 (B) 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,450 0,040 2,490 2,515 2,515 2,515 2814 10 00 Anhydrous ammonia 1,960 0,120 2,080 2,101 2,101 2,101 2814 20 00 Ammonia in aqueous solution 0,590 0,040 0,620 0,626 0,626 0,626 2834 21 00 Nitrate of potassium 1,980 0,060 2,040 2,060 2,060 2,060 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,030 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,030 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,350 0,100 1,450 1,465 1,465 1,465 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,320 0,100 1,420 1,434 1,434 1,434 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,080 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,080 1,370 1,384 1,384 1,384 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,500 0,060 1,570 1,586 1,586 1,586 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,310 0,100 2,410 2,434 2,434 2,434 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,090 2,080 2,101 2,101 2,101 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,090 2,080 2,101 2,101 2,101 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,820 0,060 3,880 3,919 3,919 3,919 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,090 2,030 2,050 2,050 2,050 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,460 0,080 1,540 1,555 1,555 1,555 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,510 0,090 1,600 1,616 1,616 1,616 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,080 0,820 0,828 0,828 0,828 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,090 1,070 1,081 1,081 1,081 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,070 0,730 0,737 0,737 0,737 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,060 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,120 1,460 1,475 1,475 1,475 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,100 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,070 1,380 1,394 1,394 1,394 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,050 0,720 0,727 0,727 0,727 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) - - - - - - 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,860 N/A 1,860 2,046 2,232 2,418 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms _ N/A _ _ _ _ 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,870 N/A 1,870 2,057 2,244 2,431 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,200 N/A 3,200 3,520 3,840 4,160 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,200 N/A 3,200 3,520 3,840 4,160 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,200 N/A 3,200 3,520 3,840 4,160 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,200 N/A 3,200 3,520 3,840 4,160 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,200 N/A 3,200 3,520 3,840 4,160 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,200 N/A 3,200 3,520 3,840 4,160 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,200 N/A 3,200 3,520 3,840 4,160 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,200 N/A 3,200 3,520 3,840 4,160 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,200 N/A 3,200 3,520 3,840 4,160 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,200 N/A 3,200 3,520 3,840 4,160 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,200 N/A 3,200 3,520 3,840 4,160 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,200 N/A 3,200 3,520 3,840 4,160 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,200 N/A 3,200 3,520 3,840 4,160 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,200 N/A 3,200 3,520 3,840 4,160 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,200 N/A 3,200 3,520 3,840 4,160 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,200 N/A 3,200 3,520 3,840 4,160 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,200 N/A 3,200 3,520 3,840 4,160 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,200 N/A 3,200 3,520 3,840 4,160 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,200 N/A 3,200 3,520 3,840 4,160 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 02 Semi-finished products of tool steel 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3 N/A 3 3,300 3,600 3,900 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3 N/A 3 3,300 3,600 3,900 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 3,980 N/A 3,980 4,378 4,776 5,174 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3 N/A 3 3,300 3,600 3,900 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3 N/A 3 3,300 3,600 3,900 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 3,980 N/A 3,980 4,378 4,776 5,174 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3 N/A 3 3,300 3,600 3,900 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3 N/A 3 3,300 3,600 3,900 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3 N/A 3 3,300 3,600 3,900 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3 N/A 3 3,300 3,600 3,900 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3 N/A 3 3,300 3,600 3,900 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3 N/A 3 3,300 3,600 3,900 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3 N/A 3 3,300 3,600 3,900 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3 N/A 3 3,300 3,600 3,900 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3 N/A 3 3,300 3,600 3,900 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,790 N/A 2,790 3,069 3,348 3,627 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,860 N/A 1,860 2,046 2,232 2,418 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,200 N/A 3,200 3,520 3,840 4,160 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,200 N/A 3,200 3,520 3,840 4,160 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,200 N/A 3,200 3,520 3,840 4,160 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,200 N/A 3,200 3,520 3,840 4,160 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,200 N/A 3,200 3,520 3,840 4,160 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,900 N/A 1,900 2,090 2,280 2,470 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,900 N/A 1,900 2,090 2,280 2,470 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,200 N/A 3,200 3,520 3,840 4,160 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,200 N/A 3,200 3,520 3,840 4,160 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 1,940 N/A 1,940 2,134 2,328 2,522 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,200 N/A 3,200 3,520 3,840 4,160 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,200 N/A 3,200 3,520 3,840 4,160 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 1,940 N/A 1,940 2,134 2,328 2,522 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 1,940 N/A 1,940 2,134 2,328 2,522 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 1,940 N/A 1,940 2,134 2,328 2,522 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,200 N/A 3,200 3,520 3,840 4,160 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,200 N/A 3,200 3,520 3,840 4,160 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,860 N/A 1,860 2,046 2,232 2,418 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,860 N/A 1,860 2,046 2,232 2,418 7307 19 90 Cast tube or pipe fittings of steel 1,940 N/A 1,940 2,134 2,328 2,522 7307 21 00 Flanges of stainless steel (excl. cast products) 1,950 N/A 1,950 2,145 2,340 2,535 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 1,950 N/A 1,950 2,145 2,340 2,535 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 1,950 N/A 1,950 2,145 2,340 2,535 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 1,950 N/A 1,950 2,145 2,340 2,535 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,550 N/A 2,550 2,805 3,060 3,315 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,550 N/A 2,550 2,805 3,060 3,315 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,380 N/A 2,380 2,618 2,856 3,094 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,200 N/A 3,200 3,520 3,840 4,160 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,200 N/A 3,200 3,520 3,840 4,160 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7318 16 Nuts of iron or steel 2,030 N/A 2,030 2,233 2,436 2,639 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,040 N/A 2,040 2,244 2,448 2,652 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2 N/A 2 2,200 2,400 2,600 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7318 29 00 Non-threaded articles, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 30 Ladders and steps, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7326 90 98 Articles of iron or steel, n.e.s. 1,940 N/A 1,940 2,134 2,328 2,522 (C) Iraq Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,280 0,050 1,330 1,463 1,596 1,729 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,260 0,090 1,350 1,485 1,620 1,755 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,190 0,090 1,290 1,419 1,548 1,677 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,460 0,050 2,520 2,545 2,545 2,545 2814 10 00 Anhydrous ammonia 1,960 0,160 2,120 2,141 2,141 2,141 2814 20 00 Ammonia in aqueous solution 0,590 0,050 0,640 0,646 0,646 0,646 2834 21 00 Nitrate of potassium 1,990 0,080 2,070 2,091 2,091 2,091 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,040 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,040 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,340 0,130 1,470 1,485 1,485 1,485 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,320 0,120 1,440 1,454 1,454 1,454 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,100 0,680 0,687 0,687 0,687 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,110 1,390 1,404 1,404 1,404 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,510 0,080 1,590 1,606 1,606 1,606 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,330 0,130 2,450 2,475 2,475 2,475 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2 0,120 2,110 2,131 2,131 2,131 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2 0,120 2,110 2,131 2,131 2,131 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,850 0,080 3,930 3,969 3,969 3,969 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,110 2,060 2,081 2,081 2,081 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,460 0,100 1,560 1,576 1,576 1,576 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,510 0,120 1,620 1,636 1,636 1,636 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,100 0,840 0,848 0,848 0,848 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,120 1,100 1,111 1,111 1,111 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,090 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,070 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,060 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,350 0,150 1,500 1,515 1,515 1,515 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,120 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,090 1,400 1,414 1,414 1,414 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,060 0,740 0,747 0,747 0,747 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Israel Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,280 0,030 1,310 1,441 1,572 1,703 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,260 0,060 1,320 1,452 1,584 1,716 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,200 0,070 1,260 1,386 1,512 1,638 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,530 0,030 2,560 2,586 2,586 2,586 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,610 0,030 0,640 0,646 0,646 0,646 2834 21 00 Nitrate of potassium 2,040 0,050 2,080 2,101 2,101 2,101 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,430 0,030 0,450 0,455 0,455 0,455 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,710 0,030 0,730 0,737 0,737 0,737 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,280 0,080 1,360 1,374 1,374 1,374 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,250 0,080 1,330 1,343 1,343 1,343 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,060 0,640 0,646 0,646 0,646 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,300 0,070 1,370 1,384 1,384 1,384 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,540 0,050 1,590 1,606 1,606 1,606 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,370 0,080 2,440 2,464 2,464 2,464 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,010 0,070 2,080 2,101 2,101 2,101 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,010 0,070 2,080 2,101 2,101 2,101 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,940 0,050 3,990 4,030 4,030 4,030 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,070 2,050 2,071 2,071 2,071 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,470 0,060 1,530 1,545 1,545 1,545 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,480 0,070 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,750 0,060 0,810 0,818 0,818 0,818 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,070 1,060 1,071 1,071 1,071 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,060 0,720 0,727 0,727 0,727 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,040 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,350 0,090 1,440 1,454 1,454 1,454 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,080 0,620 0,626 0,626 0,626 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,340 0,060 1,390 1,404 1,404 1,404 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,680 0,040 0,720 0,727 0,727 0,727 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,620 N/A 0,620 0,682 0,744 0,806 (L) 7604 10 10 Bars and rods 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7604 10 90 Profiles 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7604 21 00 Hollow profiles 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7604 29 10 Bars and rods 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7604 29 90 Profiles 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7605 Aluminium wire 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7608 Aluminium tubes and pipes 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7610 90 Other 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7610 90 90 Other 0,860 N/A 0,860 0,946 1,032 1,118 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7616 99 10 Cast 0,620 N/A 0,620 0,682 0,744 0,806 (L) 7616 99 90 Other 1,300 N/A 1,300 1,430 1,560 1,690 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Jamaica Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,090 0,050 1,130 1,243 1,356 1,469 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,090 0,080 1,170 1,287 1,404 1,521 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,030 0,090 1,120 1,232 1,344 1,456 (A) 2523 30 00 Aluminous cement - - - - - - Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Japan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,820 0,030 0,850 0,935 1,020 1,105 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,830 0,060 0,890 0,979 1,068 1,157 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,790 0,060 0,850 0,935 1,020 1,105 (A) 2523 30 00 Aluminous cement 1,800 0,150 1,940 2,134 2,328 2,522 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,130 0,060 2,190 2,212 2,212 2,212 2814 10 00 Anhydrous ammonia 2,050 0,140 2,190 2,212 2,212 2,212 2814 20 00 Ammonia in aqueous solution 0,620 0,040 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 1,790 0,080 1,870 1,889 1,889 1,889 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,040 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,040 0,810 0,818 0,818 0,818 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,110 1,520 1,535 1,535 1,535 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,110 1,480 1,495 1,495 1,495 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,080 0,690 0,697 0,697 0,697 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,210 0,090 1,300 1,313 1,313 1,313 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,360 0,080 1,440 1,454 1,454 1,454 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,100 0,120 2,210 2,232 2,232 2,232 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,810 0,110 1,910 1,929 1,929 1,929 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,810 0,110 1,910 1,929 1,929 1,929 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,330 0,090 3,420 3,454 3,454 3,454 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,760 0,100 1,860 1,879 1,879 1,879 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,380 0,090 1,470 1,485 1,485 1,485 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,100 1,570 1,586 1,586 1,586 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,710 0,080 0,790 0,798 0,798 0,798 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,900 0,100 1 1,010 1,010 1,010 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,080 0,690 0,697 0,697 0,697 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,060 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,050 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,230 0,120 1,350 1,364 1,364 1,364 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,100 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,190 0,080 1,270 1,283 1,283 1,283 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,610 0,050 0,670 0,677 0,677 0,677 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,050 N/A 1,050 1,155 1,260 1,365 (L) 7604 10 10 Bars and rods 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7604 10 90 Profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 21 00 Hollow profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 29 10 Bars and rods 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7604 29 90 Profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7605 Aluminium wire 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7608 Aluminium tubes and pipes 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 Other 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 90 Other 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7616 99 10 Cast 1,050 N/A 1,050 1,155 1,260 1,365 (L) 7616 99 90 Other 1,730 N/A 1,730 1,903 2,076 2,249 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,160 0,040 0,200 0,220 0,240 0,260 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,960 N/A 1,960 2,156 2,352 2,548 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon 5,590 N/A 5,590 6,149 6,708 7,267 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,990 N/A 1,990 2,189 2,388 2,587 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,070 N/A 2,070 2,277 2,484 2,691 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,070 N/A 2,070 2,277 2,484 2,691 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,143 N/A 2,143 2,357 2,571 2,786 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,520 N/A 3,520 3,872 4,224 4,576 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,330 N/A 3,330 3,663 3,996 4,329 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,330 N/A 3,330 3,663 3,996 4,329 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,520 N/A 3,520 3,872 4,224 4,576 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,330 N/A 3,330 3,663 3,996 4,329 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,520 N/A 3,520 3,872 4,224 4,576 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,330 N/A 3,330 3,663 3,996 4,329 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,360 N/A 3,360 3,696 4,032 4,368 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,360 N/A 3,360 3,696 4,032 4,368 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,360 N/A 3,360 3,696 4,032 4,368 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,360 N/A 3,360 3,696 4,032 4,368 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,360 N/A 3,360 3,696 4,032 4,368 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,360 N/A 3,360 3,696 4,032 4,368 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,330 N/A 3,330 3,663 3,996 4,329 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,330 N/A 3,330 3,663 3,996 4,329 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,360 N/A 3,360 3,696 4,032 4,368 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,360 N/A 3,360 3,696 4,032 4,368 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,360 N/A 3,360 3,696 4,032 4,368 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,360 N/A 3,360 3,696 4,032 4,368 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,360 N/A 3,360 3,696 4,032 4,368 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,360 N/A 3,360 3,696 4,032 4,368 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,520 N/A 3,520 3,872 4,224 4,576 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,360 N/A 3,360 3,696 4,032 4,368 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,370 N/A 3,370 3,707 4,044 4,381 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,690 N/A 3,690 4,059 4,428 4,797 (F) 7224 90 02 Semi-finished products of tool steel 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,690 N/A 3,690 4,059 4,428 4,797 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,690 N/A 3,690 4,059 4,428 4,797 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,620 N/A 4,620 5,082 5,544 6,006 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,500 N/A 3,500 3,850 4,200 4,550 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,620 N/A 4,620 5,082 5,544 6,006 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,500 N/A 3,500 3,850 4,200 4,550 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,690 N/A 3,690 4,059 4,428 4,797 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,690 N/A 3,690 4,059 4,428 4,797 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,530 N/A 3,530 3,883 4,236 4,589 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,950 N/A 2,950 3,245 3,540 3,835 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,150 N/A 2,150 2,365 2,580 2,795 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,320 N/A 3,320 3,652 3,984 4,316 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,320 N/A 3,320 3,652 3,984 4,316 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,320 N/A 3,320 3,652 3,984 4,316 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,320 N/A 3,320 3,652 3,984 4,316 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,320 N/A 3,320 3,652 3,984 4,316 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,080 N/A 2,080 2,288 2,496 2,704 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,080 N/A 2,080 2,288 2,496 2,704 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,360 N/A 3,360 3,696 4,032 4,368 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,360 N/A 3,360 3,696 4,032 4,368 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,100 N/A 2,100 2,310 2,520 2,730 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,360 N/A 3,360 3,696 4,032 4,368 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,330 N/A 3,330 3,663 3,996 4,329 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,140 N/A 2,140 2,354 2,568 2,782 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,110 N/A 2,110 2,321 2,532 2,743 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,140 N/A 2,140 2,354 2,568 2,782 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,360 N/A 3,360 3,696 4,032 4,368 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,360 N/A 3,360 3,696 4,032 4,368 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,220 N/A 2,220 2,442 2,664 2,886 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,220 N/A 2,220 2,442 2,664 2,886 7307 19 90 Cast tube or pipe fittings of steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,860 N/A 2,860 3,146 3,432 3,718 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,860 N/A 2,860 3,146 3,432 3,718 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,860 N/A 2,860 3,146 3,432 3,718 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,860 N/A 2,860 3,146 3,432 3,718 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,110 N/A 2,110 2,321 2,532 2,743 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,950 N/A 2,950 3,245 3,540 3,835 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,160 N/A 3,160 3,476 3,792 4,108 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,130 N/A 2,130 2,343 2,556 2,769 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,130 N/A 3,130 3,443 3,756 4,069 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,300 N/A 3,300 3,630 3,960 4,290 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,300 N/A 3,300 3,630 3,960 4,290 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,800 N/A 2,800 3,080 3,360 3,640 (C) 7318 16 Nuts of iron or steel 3,060 N/A 3,060 3,366 3,672 3,978 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,280 N/A 2,280 2,508 2,736 2,964 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,220 N/A 2,220 2,442 2,664 2,886 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 30 Ladders and steps, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,100 N/A 2,100 2,310 2,520 2,730 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,130 N/A 2,130 2,343 2,556 2,769 (C) Jordan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,290 0,040 1,330 1,463 1,596 1,729 (B) 2523 10 00 Grey clinker - - - - - - 2523 21 00 White Portland cement 1,270 0,140 1,410 1,551 1,692 1,833 2523 29 00 Grey Portland cement - - - - - - 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,490 0,040 2,520 2,545 2,545 2,545 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,610 0,030 0,650 0,657 0,657 0,657 2834 21 00 Nitrate of potassium 2,020 0,050 2,070 2,091 2,091 2,091 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,030 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,030 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,370 0,090 1,460 1,475 1,475 1,475 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,340 0,080 1,430 1,444 1,444 1,444 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,060 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,310 0,070 1,380 1,394 1,394 1,394 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,530 0,060 1,580 1,596 1,596 1,596 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,350 0,080 2,440 2,464 2,464 2,464 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,020 0,080 2,090 2,111 2,111 2,111 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,020 0,080 2,090 2,111 2,111 2,111 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,880 0,060 3,940 3,979 3,979 3,979 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,970 0,070 2,050 2,071 2,071 2,071 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,490 0,070 1,550 1,566 1,566 1,566 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,530 0,080 1,610 1,626 1,626 1,626 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,760 0,070 0,820 0,828 0,828 0,828 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,990 0,080 1,070 1,081 1,081 1,081 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,670 0,060 0,730 0,737 0,737 0,737 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,050 0,530 0,535 0,535 0,535 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,360 0,100 1,460 1,475 1,475 1,475 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,090 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,330 0,060 1,390 1,404 1,404 1,404 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,680 0,040 0,720 0,727 0,727 0,727 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7604 10 10 Bars and rods 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7604 10 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 21 00 Hollow profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 10 Bars and rods 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7604 29 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7605 Aluminium wire 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7608 Aluminium tubes and pipes 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 99 10 Cast 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7616 99 90 Other 1,150 N/A 1,150 1,265 1,380 1,495 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Kazakhstan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,350 0,040 1,390 1,529 1,668 1,807 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,350 0,070 1,420 1,562 1,704 1,846 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,280 0,070 1,350 1,485 1,620 1,755 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,730 0,040 2,770 2,798 2,798 2,798 2814 10 00 Anhydrous ammonia 2,160 0,140 2,300 2,323 2,323 2,323 2814 20 00 Ammonia in aqueous solution 0,650 0,040 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 2,200 0,070 2,270 2,293 2,293 2,293 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,040 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,040 0,840 0,848 0,848 0,848 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,110 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,110 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,080 0,720 0,727 0,727 0,727 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,420 0,090 1,510 1,525 1,525 1,525 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,670 0,070 1,740 1,757 1,757 1,757 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,570 0,110 2,670 2,697 2,697 2,697 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,200 0,100 2,300 2,323 2,323 2,323 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,200 0,100 2,300 2,323 2,323 2,323 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,260 0,070 4,330 4,373 4,373 4,373 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,090 2,250 2,273 2,273 2,273 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,610 0,080 1,700 1,717 1,717 1,717 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,650 0,100 1,750 1,768 1,768 1,768 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,820 0,080 0,900 0,909 0,909 0,909 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,100 1,180 1,192 1,192 1,192 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,730 0,080 0,800 0,808 0,808 0,808 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,060 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,050 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,480 0,120 1,600 1,616 1,616 1,616 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,100 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,450 0,070 1,520 1,535 1,535 1,535 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,740 0,050 0,790 0,798 0,798 0,798 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,870 N/A 1,870 2,057 2,244 2,431 (K) 7603 Aluminium powders and flakes 1,990 N/A 1,990 2,189 2,388 2,587 (K) 7604 10 10 Bars and rods 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7604 10 90 Profiles 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7604 21 00 Hollow profiles 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7604 29 10 Bars and rods 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7604 29 90 Profiles 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7605 Aluminium wire 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7608 Aluminium tubes and pipes 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 90 Other 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 90 90 Other 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7616 99 10 Cast 1,990 N/A 1,990 2,189 2,388 2,587 (K) 7616 99 90 Other 2,670 N/A 2,670 2,937 3,204 3,471 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,170 0,170 0,340 0,374 0,408 0,442 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 4,960 N/A 4,960 5,456 5,952 6,448 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon 2,870 N/A 2,870 3,157 3,444 3,731 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 4,990 N/A 4,990 5,489 5,988 6,487 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 5,290 N/A 5,290 5,819 6,348 6,877 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 5,290 N/A 5,290 5,819 6,348 6,877 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 5,290 N/A 5,290 5,819 6,348 6,877 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 5,290 N/A 5,290 5,819 6,348 6,877 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 4,600 N/A 4,600 5,060 5,520 5,980 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 4,780 N/A 4,780 5,258 5,736 6,214 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 4,780 N/A 4,780 5,258 5,736 6,214 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 4,600 N/A 4,600 5,060 5,520 5,980 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 4,780 N/A 4,780 5,258 5,736 6,214 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 4,600 N/A 4,600 5,060 5,520 5,980 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 4,780 N/A 4,780 5,258 5,736 6,214 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 4,860 N/A 4,860 5,346 5,832 6,318 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 4,860 N/A 4,860 5,346 5,832 6,318 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 4,860 N/A 4,860 5,346 5,832 6,318 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 4,860 N/A 4,860 5,346 5,832 6,318 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 4,860 N/A 4,860 5,346 5,832 6,318 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 4,860 N/A 4,860 5,346 5,832 6,318 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 4,780 N/A 4,780 5,258 5,736 6,214 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 4,780 N/A 4,780 5,258 5,736 6,214 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 4,860 N/A 4,860 5,346 5,832 6,318 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 4,860 N/A 4,860 5,346 5,832 6,318 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 4,610 N/A 4,610 5,071 5,532 5,993 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 4,610 N/A 4,610 5,071 5,532 5,993 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 4,610 N/A 4,610 5,071 5,532 5,993 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 4,610 N/A 4,610 5,071 5,532 5,993 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 4,600 N/A 4,600 5,060 5,520 5,980 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 4,610 N/A 4,610 5,071 5,532 5,993 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 4,610 N/A 4,610 5,071 5,532 5,993 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7224 90 02 Semi-finished products of tool steel 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 6,780 N/A 6,780 7,458 8,136 8,814 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 5,340 N/A 5,340 5,874 6,408 6,942 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 6,780 N/A 6,780 7,458 8,136 8,814 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 5,340 N/A 5,340 5,874 6,408 6,942 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 5,170 N/A 5,170 5,687 6,204 6,721 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 5,170 N/A 5,170 5,687 6,204 6,721 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 5,170 N/A 5,170 5,687 6,204 6,721 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 4,960 N/A 4,960 5,456 5,952 6,448 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 4,610 N/A 4,610 5,071 5,532 5,993 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 4,610 N/A 4,610 5,071 5,532 5,993 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 4,610 N/A 4,610 5,071 5,532 5,993 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 4,610 N/A 4,610 5,071 5,532 5,993 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 4,610 N/A 4,610 5,071 5,532 5,993 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 5,120 N/A 5,120 5,632 6,144 6,656 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 5,120 N/A 5,120 5,632 6,144 6,656 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,860 N/A 4,860 5,346 5,832 6,318 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,860 N/A 4,860 5,346 5,832 6,318 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 5,290 N/A 5,290 5,819 6,348 6,877 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,860 N/A 4,860 5,346 5,832 6,318 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,780 N/A 4,780 5,258 5,736 6,214 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 5,340 N/A 5,340 5,874 6,408 6,942 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 5,420 N/A 5,420 5,962 6,504 7,046 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 4,860 N/A 4,860 5,346 5,832 6,318 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,860 N/A 4,860 5,346 5,832 6,318 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 4,960 N/A 4,960 5,456 5,952 6,448 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 4,960 N/A 4,960 5,456 5,952 6,448 7307 19 90 Cast tube or pipe fittings of steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 5,150 N/A 5,150 5,665 6,180 6,695 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 5,150 N/A 5,150 5,665 6,180 6,695 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 5,150 N/A 5,150 5,665 6,180 6,695 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 5,150 N/A 5,150 5,665 6,180 6,695 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 4,610 N/A 4,610 5,071 5,532 5,993 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 4,610 N/A 4,610 5,071 5,532 5,993 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 16 Nuts of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7318 29 00 Non-threaded articles, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 30 Ladders and steps, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 5,180 N/A 5,180 5,698 6,216 6,734 (C) 7326 90 98 Articles of iron or steel, n.e.s. 5,360 N/A 5,360 5,896 6,432 6,968 (C) Kenya Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,700 0,040 1,740 1,757 1,757 1,757 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,600 0,040 0,650 0,657 0,657 0,657 2834 21 00 Nitrate of potassium 1,500 0,060 1,560 1,576 1,576 1,576 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,040 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,040 0,800 0,808 0,808 0,808 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,380 0,100 1,490 1,505 1,505 1,505 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,350 0,100 1,460 1,475 1,475 1,475 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,070 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,060 0,080 1,140 1,151 1,151 1,151 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,140 0,060 1,200 1,212 1,212 1,212 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,760 0,090 1,850 1,869 1,869 1,869 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,520 0,080 1,610 1,626 1,626 1,626 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,520 0,080 1,610 1,626 1,626 1,626 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,650 0,070 2,720 2,747 2,747 2,747 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,480 0,080 1,560 1,576 1,576 1,576 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,220 0,080 1,300 1,313 1,313 1,313 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,340 0,090 1,440 1,454 1,454 1,454 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,630 0,070 0,700 0,707 0,707 0,707 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,770 0,080 0,840 0,848 0,848 0,848 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,060 0,580 0,586 0,586 0,586 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,470 0,050 0,530 0,535 0,535 0,535 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,050 0,090 1,140 1,151 1,151 1,151 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,090 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,010 0,060 1,070 1,081 1,081 1,081 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,520 0,040 0,560 0,566 0,566 0,566 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,800 N/A 0,800 0,880 0,960 1,040 (L) 7604 10 10 Bars and rods 1,020 N/A 1,020 1,122 1,224 1,326 (L) 7604 10 90 Profiles 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7604 21 00 Hollow profiles 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7604 29 10 Bars and rods 1,020 N/A 1,020 1,122 1,224 1,326 (L) 7604 29 90 Profiles 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7605 Aluminium wire 1,020 N/A 1,020 1,122 1,224 1,326 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7608 Aluminium tubes and pipes 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7610 90 Other 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7610 90 90 Other 1,040 N/A 1,040 1,144 1,248 1,352 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,020 N/A 1,020 1,122 1,224 1,326 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,480 N/A 1,480 1,628 1,776 1,924 (L) 7616 99 10 Cast 0,800 N/A 0,800 0,880 0,960 1,040 (L) 7616 99 90 Other 1,480 N/A 1,480 1,628 1,776 1,924 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Kuwait Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,830 0,040 0,870 0,957 1,044 1,131 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,950 0,080 1,030 1,133 1,236 1,339 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,910 0,080 0,990 1,089 1,188 1,287 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,450 0,070 2,510 2,535 2,535 2,535 2814 10 00 Anhydrous ammonia 1,960 0,140 2,100 2,121 2,121 2,121 2814 20 00 Ammonia in aqueous solution 0,590 0,040 0,630 0,636 0,636 0,636 2834 21 00 Nitrate of potassium 1,980 0,080 2,070 2,091 2,091 2,091 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,040 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,040 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,350 0,110 1,460 1,475 1,475 1,475 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,320 0,110 1,430 1,444 1,444 1,444 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,080 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,100 1,380 1,394 1,394 1,394 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,500 0,080 1,590 1,606 1,606 1,606 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,310 0,130 2,440 2,464 2,464 2,464 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,120 2,100 2,121 2,121 2,121 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,120 2,100 2,121 2,121 2,121 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,820 0,100 3,920 3,959 3,959 3,959 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,110 2,050 2,071 2,071 2,071 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,460 0,090 1,560 1,576 1,576 1,576 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,510 0,110 1,620 1,636 1,636 1,636 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,090 0,830 0,838 0,838 0,838 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,110 1,090 1,101 1,101 1,101 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,080 0,750 0,758 0,758 0,758 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,060 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,050 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,140 1,480 1,495 1,495 1,495 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,110 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,090 1,390 1,404 1,404 1,404 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,060 0,730 0,737 0,737 0,737 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 7603 Aluminium powders and flakes 0,630 N/A 0,630 0,693 0,756 0,819 7604 10 10 Bars and rods 0,860 N/A 0,860 0,946 1,032 1,118 7604 10 90 Profiles 0,870 N/A 0,870 0,957 1,044 1,131 7604 21 00 Hollow profiles 0,870 N/A 0,870 0,957 1,044 1,131 7604 29 10 Bars and rods 0,860 N/A 0,860 0,946 1,032 1,118 7604 29 90 Profiles 0,870 N/A 0,870 0,957 1,044 1,131 7605 Aluminium wire 0,860 N/A 0,860 0,946 1,032 1,118 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,320 N/A 1,320 1,452 1,584 1,716 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,320 N/A 1,320 1,452 1,584 1,716 7608 Aluminium tubes and pipes 0,870 N/A 0,870 0,957 1,044 1,131 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,870 N/A 0,870 0,957 1,044 1,131 7610 10 00 Doors, windows and their frames and thresholds for doors 0,870 N/A 0,870 0,957 1,044 1,131 7610 90 Other 0,870 N/A 0,870 0,957 1,044 1,131 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,870 N/A 0,870 0,957 1,044 1,131 7610 90 90 Other 0,870 N/A 0,870 0,957 1,044 1,131 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,320 N/A 1,320 1,452 1,584 1,716 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,320 N/A 1,320 1,452 1,584 1,716 7613 00 00 Aluminium containers for compressed or liquefied gas 1,320 N/A 1,320 1,452 1,584 1,716 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,860 N/A 0,860 0,946 1,032 1,118 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,320 N/A 1,320 1,452 1,584 1,716 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,320 N/A 1,320 1,452 1,584 1,716 7616 99 10 Cast 0,630 N/A 0,630 0,693 0,756 0,819 7616 99 90 Other 1,320 N/A 1,320 1,452 1,584 1,716 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 13,450 N/A 13,450 14,795 16,140 17,485 Kyrgyzstan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0 1,360 1,496 1,632 1,768 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,360 0,010 1,360 1,496 1,632 1,768 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,290 0,010 1,300 1,430 1,560 1,690 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,770 0,040 2,810 2,838 2,838 2,838 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,040 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 2,230 0,060 2,290 2,313 2,313 2,313 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,030 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,030 0,840 0,848 0,848 0,848 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,100 1,570 1,586 1,586 1,586 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,090 1,530 1,545 1,545 1,545 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,060 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,430 0,070 1,500 1,515 1,515 1,515 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,690 0,060 1,750 1,768 1,768 1,768 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,600 0,090 2,690 2,717 2,717 2,717 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,230 0,080 2,310 2,333 2,333 2,333 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,230 0,080 2,310 2,333 2,333 2,333 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,330 0,060 4,390 4,434 4,434 4,434 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,180 0,080 2,260 2,283 2,283 2,283 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,630 0,070 1,700 1,717 1,717 1,717 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,660 0,080 1,750 1,768 1,768 1,768 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,820 0,060 0,890 0,899 0,899 0,899 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,070 1,160 1,172 1,172 1,172 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,740 0,060 0,790 0,798 0,798 0,798 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,050 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,040 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,500 0,090 1,590 1,606 1,606 1,606 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,090 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,060 1,520 1,535 1,535 1,535 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,750 0,040 0,790 0,798 0,798 0,798 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Laos Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Lebanon Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,290 0,070 1,360 1,496 1,632 1,768 (B) 2523 10 00 Grey clinker 0,830 0,050 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement 1,270 0,160 1,430 1,573 1,716 1,859 2523 29 00 Grey Portland cement 0,830 0,100 0,930 1,023 1,116 1,209 2523 90 00 White hydraulic cements 1,310 0,210 1,520 1,672 1,824 1,976 (B) 2523 90 00 Grey hydraulic cements 0,790 0,100 0,890 0,979 1,068 1,157 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,580 0,060 2,640 2,666 2,666 2,666 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,640 0,060 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 2,100 0,090 2,190 2,212 2,212 2,212 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,480 0,050 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,800 0,050 0,850 0,859 0,859 0,859 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,450 0,140 1,600 1,616 1,616 1,616 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,420 0,140 1,560 1,576 1,576 1,576 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,630 0,110 0,740 0,747 0,747 0,747 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,360 0,120 1,480 1,495 1,495 1,495 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,590 0,090 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,450 0,140 2,590 2,616 2,616 2,616 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,100 0,130 2,230 2,252 2,252 2,252 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,100 0,130 2,230 2,252 2,252 2,252 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,030 0,090 4,120 4,161 4,161 4,161 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,060 0,120 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,560 0,110 1,670 1,687 1,687 1,687 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,610 0,130 1,740 1,757 1,757 1,757 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,790 0,110 0,900 0,909 0,909 0,909 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,030 0,130 1,160 1,172 1,172 1,172 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,700 0,100 0,800 0,808 0,808 0,808 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,080 0,580 0,586 0,586 0,586 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,060 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,420 0,160 1,580 1,596 1,596 1,596 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,130 0,710 0,717 0,717 0,717 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,390 0,100 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,710 0,070 0,780 0,788 0,788 0,788 Libya Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,830 0,040 0,870 0,957 1,044 1,131 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,830 0,090 0,910 1,001 1,092 1,183 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,790 0,090 0,880 0,968 1,056 1,144 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,680 0,050 1,730 1,747 1,747 1,747 2814 10 00 Anhydrous ammonia 2,010 0,160 2,170 2,192 2,192 2,192 2814 20 00 Ammonia in aqueous solution 0,600 0,050 0,650 0,657 0,657 0,657 2834 21 00 Nitrate of potassium 1,490 0,080 1,560 1,576 1,576 1,576 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,040 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,040 0,800 0,808 0,808 0,808 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,380 0,120 1,500 1,515 1,515 1,515 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,350 0,120 1,470 1,485 1,485 1,485 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,090 0,690 0,697 0,697 0,697 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,060 0,100 1,160 1,172 1,172 1,172 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,130 0,080 1,210 1,222 1,222 1,222 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,740 0,120 1,860 1,879 1,879 1,879 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,510 0,110 1,620 1,636 1,636 1,636 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,510 0,110 1,620 1,636 1,636 1,636 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,620 0,080 2,700 2,727 2,727 2,727 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,460 0,110 1,570 1,586 1,586 1,586 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,210 0,100 1,310 1,323 1,323 1,323 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,340 0,120 1,450 1,465 1,465 1,465 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,630 0,100 0,720 0,727 0,727 0,727 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,760 0,120 0,880 0,889 0,889 0,889 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,090 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,470 0,070 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,060 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,040 0,140 1,180 1,192 1,192 1,192 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,110 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1 0,090 1,090 1,101 1,101 1,101 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,520 0,060 0,580 0,586 0,586 0,586 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Madagascar Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,240 0,050 1,290 1,419 1,548 1,677 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,240 0,080 1,330 1,463 1,596 1,729 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,180 0,080 1,270 1,397 1,524 1,651 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,060 1,860 1,879 1,879 1,879 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,710 0,050 0,760 0,768 0,768 0,768 2834 21 00 Nitrate of potassium 1,600 0,060 1,670 1,687 1,687 1,687 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,030 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,030 0,770 0,778 0,778 0,778 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,350 0,090 1,440 1,454 1,454 1,454 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,320 0,090 1,410 1,424 1,424 1,424 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,040 0,650 0,657 0,657 0,657 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,110 0,060 1,160 1,172 1,172 1,172 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,200 0,050 1,250 1,263 1,263 1,263 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,840 0,080 1,920 1,939 1,939 1,939 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,540 0,060 1,600 1,616 1,616 1,616 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,540 0,060 1,600 1,616 1,616 1,616 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,810 0,090 2,900 2,929 2,929 2,929 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,540 0,060 1,600 1,616 1,616 1,616 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,260 0,060 1,330 1,343 1,343 1,343 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,350 0,080 1,420 1,434 1,434 1,434 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,640 0,030 0,680 0,687 0,687 0,687 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,760 0,030 0,800 0,808 0,808 0,808 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,020 0,530 0,535 0,535 0,535 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,040 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,020 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,050 0,040 1,090 1,101 1,101 1,101 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,040 0,580 0,586 0,586 0,586 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,040 1,090 1,101 1,101 1,101 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,520 0,020 0,550 0,556 0,556 0,556 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Malaysia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,290 0,060 1,340 1,474 1,608 1,742 (B) 2523 10 00 Grey clinker 0,870 0,040 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement 1,260 0,140 1,400 1,540 1,680 1,820 2523 29 00 Grey Portland cement 0,870 0,070 0,950 1,045 1,140 1,235 2523 90 00 White hydraulic cements 1,290 0,180 1,470 1,617 1,764 1,911 (B) 2523 90 00 Grey hydraulic cements 0,830 0,080 0,910 1,001 1,092 1,183 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,150 0,060 2,210 2,232 2,232 2,232 2814 10 00 Anhydrous ammonia 2,050 0,170 2,220 2,242 2,242 2,242 2814 20 00 Ammonia in aqueous solution 0,620 0,050 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 1,810 0,080 1,890 1,909 1,909 1,909 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,040 0,510 0,515 0,515 0,515 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,040 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,130 1,540 1,555 1,555 1,555 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,130 1,500 1,515 1,515 1,515 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,100 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,210 0,110 1,330 1,343 1,343 1,343 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,370 0,090 1,460 1,475 1,475 1,475 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,110 0,130 2,240 2,262 2,262 2,262 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,820 0,120 1,940 1,959 1,959 1,959 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,820 0,120 1,940 1,959 1,959 1,959 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,360 0,090 3,450 3,485 3,485 3,485 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,770 0,120 1,890 1,909 1,909 1,909 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,390 0,100 1,490 1,505 1,505 1,505 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,120 1,590 1,606 1,606 1,606 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,710 0,100 0,810 0,818 0,818 0,818 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,900 0,120 1,020 1,030 1,030 1,030 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,090 0,710 0,717 0,717 0,717 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,070 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,060 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,240 0,150 1,390 1,404 1,404 1,404 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,120 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,200 0,090 1,290 1,303 1,303 1,303 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,620 0,060 0,680 0,687 0,687 0,687 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 2,409 N/A 2,409 2,650 2,891 3,131 (K) 7604 10 10 Bars and rods 2,694 N/A 2,694 2,963 3,232 3,502 (K) 7604 10 90 Profiles 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7604 21 00 Hollow profiles 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7604 29 10 Bars and rods 2,694 N/A 2,694 2,963 3,232 3,502 (K) 7604 29 90 Profiles 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7605 Aluminium wire 2,694 N/A 2,694 2,963 3,232 3,502 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7608 Aluminium tubes and pipes 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7610 90 Other 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7610 90 90 Other 2,720 N/A 2,720 2,992 3,264 3,535 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,694 N/A 2,694 2,963 3,232 3,502 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 3,289 N/A 3,289 3,618 3,947 4,276 (K) 7616 99 10 Cast 2,409 N/A 2,409 2,650 2,891 3,131 (K) 7616 99 90 Other 3,289 N/A 3,289 3,618 3,947 4,276 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Mali Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,050 0,900 0,990 1,080 1,170 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,910 0,080 0,980 1,078 1,176 1,274 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,860 0,080 0,940 1,034 1,128 1,222 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,740 0,050 1,790 1,808 1,808 1,808 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,660 0,050 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 1,530 0,060 1,590 1,606 1,606 1,606 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,500 0,040 0,540 0,545 0,545 0,545 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,820 0,040 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,490 0,120 1,610 1,626 1,626 1,626 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,460 0,120 1,580 1,596 1,596 1,596 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,040 0,610 0,616 0,616 0,616 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,050 0,050 1,100 1,111 1,111 1,111 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,140 0,040 1,190 1,202 1,202 1,202 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,760 0,070 1,830 1,848 1,848 1,848 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,060 1,530 1,545 1,545 1,545 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,060 1,530 1,545 1,545 1,545 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,720 0,080 2,790 2,818 2,818 2,818 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,060 1,530 1,545 1,545 1,545 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,270 0,070 1,350 1,364 1,364 1,364 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,390 0,090 1,480 1,495 1,495 1,495 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,610 0,030 0,640 0,646 0,646 0,646 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,730 0,030 0,760 0,768 0,768 0,768 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,020 0,500 0,505 0,505 0,505 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,030 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,020 0,320 0,323 0,323 0,323 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1 0,040 1,040 1,050 1,050 1,050 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,500 0,040 0,540 0,545 0,545 0,545 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1 0,040 1,040 1,050 1,050 1,050 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,500 0,020 0,520 0,525 0,525 0,525 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 0 N/A 0 0 0 0 Mauritius Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,690 0,050 1,740 1,757 1,757 1,757 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,640 0,050 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 1,520 0,080 1,590 1,606 1,606 1,606 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,480 0,040 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,790 0,040 0,830 0,838 0,838 0,838 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,440 0,120 1,560 1,576 1,576 1,576 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,410 0,120 1,520 1,535 1,535 1,535 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,630 0,090 0,720 0,727 0,727 0,727 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,090 0,100 1,190 1,202 1,202 1,202 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,160 0,080 1,230 1,242 1,242 1,242 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,780 0,120 1,900 1,919 1,919 1,919 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,530 0,110 1,640 1,656 1,656 1,656 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,530 0,110 1,640 1,656 1,656 1,656 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,640 0,080 2,720 2,747 2,747 2,747 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,490 0,100 1,600 1,616 1,616 1,616 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,250 0,100 1,340 1,353 1,353 1,353 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,380 0,110 1,490 1,505 1,505 1,505 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,650 0,090 0,740 0,747 0,747 0,747 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,780 0,110 0,890 0,899 0,899 0,899 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,080 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,070 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,050 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,060 0,140 1,190 1,202 1,202 1,202 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,110 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,020 0,080 1,110 1,121 1,121 1,121 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,530 0,060 0,590 0,596 0,596 0,596 Mauritania Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker - - - - - - 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,100 0,090 1,190 1,309 1,428 1,547 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,050 0,090 1,140 1,254 1,368 1,482 (A) 2523 30 00 Aluminous cement - - - - - - Mexico Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,880 0,040 1,920 1,939 1,939 1,939 2814 10 00 Anhydrous ammonia 2,260 0,130 2,400 2,424 2,424 2,424 2814 20 00 Ammonia in aqueous solution 0,680 0,040 0,720 0,727 0,727 0,727 2834 21 00 Nitrate of potassium 1,660 0,060 1,730 1,747 1,747 1,747 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,030 0,540 0,545 0,545 0,545 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,030 0,870 0,879 0,879 0,879 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,100 1,630 1,646 1,646 1,646 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,100 1,590 1,606 1,606 1,606 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,070 0,730 0,737 0,737 0,737 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,080 1,260 1,273 1,273 1,273 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,270 0,060 1,330 1,343 1,343 1,343 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,100 2,040 2,060 2,060 2,060 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,680 0,090 1,770 1,788 1,788 1,788 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,680 0,090 1,770 1,788 1,788 1,788 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,930 0,060 3 3,030 3,030 3,030 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,080 1,720 1,737 1,737 1,737 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,350 0,080 1,430 1,444 1,444 1,444 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,090 1,580 1,596 1,596 1,596 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,070 0,770 0,778 0,778 0,778 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,850 0,090 0,930 0,939 0,939 0,939 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,070 0,640 0,646 0,646 0,646 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,050 0,580 0,586 0,586 0,586 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,040 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,150 0,110 1,260 1,273 1,273 1,273 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,100 0,710 0,717 0,717 0,717 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,120 0,070 1,180 1,192 1,192 1,192 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,580 0,050 0,620 0,626 0,626 0,626 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7604 10 10 Bars and rods 1,410 N/A 1,410 1,551 1,692 1,833 (L) 7604 10 90 Profiles 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7604 21 00 Hollow profiles 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7604 29 10 Bars and rods 1,410 N/A 1,410 1,551 1,692 1,833 (L) 7604 29 90 Profiles 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7605 Aluminium wire 1,410 N/A 1,410 1,551 1,692 1,833 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7608 Aluminium tubes and pipes 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7610 90 Other 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7610 90 90 Other 1,420 N/A 1,420 1,562 1,704 1,846 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,410 N/A 1,410 1,551 1,692 1,833 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,860 N/A 1,860 2,046 2,232 2,418 (L) 7616 99 10 Cast 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7616 99 90 Other 1,860 N/A 1,860 2,046 2,232 2,418 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,120 0,010 0,130 0,143 0,156 0,169 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,580 N/A 2,580 2,838 3,096 3,354 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - - - - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 0,580 N/A 0,580 0,638 0,696 0,754 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,570 N/A 2,570 2,827 3,084 3,341 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,750 N/A 2,750 3,025 3,300 3,575 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,750 N/A 2,750 3,025 3,300 3,575 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,750 N/A 2,750 3,025 3,300 3,575 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,750 N/A 2,750 3,025 3,300 3,575 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,110 N/A 3,110 3,421 3,732 4,043 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,240 N/A 3,240 3,564 3,888 4,212 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,240 N/A 3,240 3,564 3,888 4,212 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,240 N/A 3,240 3,564 3,888 4,212 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,240 N/A 3,240 3,564 3,888 4,212 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,300 N/A 3,300 3,630 3,960 4,290 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,300 N/A 3,300 3,630 3,960 4,290 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,240 N/A 3,240 3,564 3,888 4,212 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,240 N/A 3,240 3,564 3,888 4,212 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,300 N/A 3,300 3,630 3,960 4,290 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,300 N/A 3,300 3,630 3,960 4,290 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,310 N/A 3,310 3,641 3,972 4,303 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,310 N/A 3,310 3,641 3,972 4,303 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,310 N/A 3,310 3,641 3,972 4,303 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,310 N/A 3,310 3,641 3,972 4,303 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,110 N/A 3,110 3,421 3,732 4,043 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,310 N/A 3,310 3,641 3,972 4,303 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,310 N/A 3,310 3,641 3,972 4,303 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 02 Semi-finished products of tool steel 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,790 N/A 4,790 5,269 5,748 6,227 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,650 N/A 3,650 4,015 4,380 4,745 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,790 N/A 4,790 5,269 5,748 6,227 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,650 N/A 3,650 4,015 4,380 4,745 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,650 N/A 3,650 4,015 4,380 4,745 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,710 N/A 3,710 4,081 4,452 4,823 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,710 N/A 3,710 4,081 4,452 4,823 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,710 N/A 3,710 4,081 4,452 4,823 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,710 N/A 3,710 4,081 4,452 4,823 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,710 N/A 3,710 4,081 4,452 4,823 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,960 N/A 2,960 3,256 3,552 3,848 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,800 N/A 2,800 3,080 3,360 3,640 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,210 N/A 3,210 3,531 3,852 4,173 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,210 N/A 3,210 3,531 3,852 4,173 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,210 N/A 3,210 3,531 3,852 4,173 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,660 N/A 2,660 2,926 3,192 3,458 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,660 N/A 2,660 2,926 3,192 3,458 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,300 N/A 3,300 3,630 3,960 4,290 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,300 N/A 3,300 3,630 3,960 4,290 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,750 N/A 2,750 3,025 3,300 3,575 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,300 N/A 3,300 3,630 3,960 4,290 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,240 N/A 3,240 3,564 3,888 4,212 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,760 N/A 2,760 3,036 3,312 3,588 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,700 N/A 2,700 2,970 3,240 3,510 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,760 N/A 2,760 3,036 3,312 3,588 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,300 N/A 3,300 3,630 3,960 4,290 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,300 N/A 3,300 3,630 3,960 4,290 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,550 N/A 2,550 2,805 3,060 3,315 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,550 N/A 2,550 2,805 3,060 3,315 7307 19 90 Cast tube or pipe fittings of steel 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,930 N/A 2,930 3,223 3,516 3,809 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,930 N/A 2,930 3,223 3,516 3,809 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,930 N/A 2,930 3,223 3,516 3,809 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,930 N/A 2,930 3,223 3,516 3,809 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,990 N/A 2,990 3,289 3,588 3,887 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,130 N/A 3,130 3,443 3,756 4,069 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,060 N/A 3,060 3,366 3,672 3,978 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,180 N/A 3,180 3,498 3,816 4,134 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,180 N/A 3,180 3,498 3,816 4,134 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,900 N/A 2,900 3,190 3,480 3,770 (C) 7318 16 Nuts of iron or steel 3,060 N/A 3,060 3,366 3,672 3,978 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7326 90 30 Ladders and steps, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,670 N/A 2,670 2,937 3,204 3,471 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,810 N/A 2,810 3,091 3,372 3,653 (C) Moldova Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,340 0,040 1,380 1,518 1,656 1,794 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,340 0,070 1,410 1,551 1,692 1,833 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,760 0,040 2,800 2,828 2,828 2,828 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,040 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 2,230 0,060 2,290 2,313 2,313 2,313 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,030 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,030 0,840 0,848 0,848 0,848 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,100 1,570 1,586 1,586 1,586 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,100 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,080 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,420 0,080 1,510 1,525 1,525 1,525 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,680 0,060 1,750 1,768 1,768 1,768 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,590 0,100 2,690 2,717 2,717 2,717 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,220 0,090 2,310 2,333 2,333 2,333 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,220 0,090 2,310 2,333 2,333 2,333 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,310 0,070 4,380 4,424 4,424 4,424 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,170 0,090 2,260 2,283 2,283 2,283 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,620 0,080 1,700 1,717 1,717 1,717 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,660 0,090 1,760 1,778 1,778 1,778 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,820 0,080 0,900 0,909 0,909 0,909 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,090 1,180 1,192 1,192 1,192 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,740 0,070 0,810 0,818 0,818 0,818 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,060 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,040 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,500 0,110 1,610 1,626 1,626 1,626 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,100 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,460 0,070 1,530 1,545 1,545 1,545 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,750 0,050 0,800 0,808 0,808 0,808 Mongolia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0,070 1,430 1,573 1,716 1,859 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,360 0,130 1,490 1,639 1,788 1,937 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,290 0,130 1,420 1,562 1,704 1,846 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,190 0,090 2,290 2,313 2,313 2,313 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,090 0,740 0,747 0,747 0,747 2834 21 00 Nitrate of potassium 1,820 0,110 1,930 1,949 1,949 1,949 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,410 0,050 0,460 0,465 0,465 0,465 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,670 0,050 0,730 0,737 0,737 0,737 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,230 0,160 1,390 1,404 1,404 1,404 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,200 0,160 1,360 1,374 1,374 1,374 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,070 0,630 0,636 0,636 0,636 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,100 1,270 1,283 1,283 1,283 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,360 0,080 1,440 1,454 1,454 1,454 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,090 0,130 2,220 2,242 2,242 2,242 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,110 1,860 1,879 1,879 1,879 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,110 1,860 1,879 1,879 1,879 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,420 0,150 3,570 3,606 3,606 3,606 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,110 1,860 1,879 1,879 1,879 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,110 1,450 1,465 1,465 1,465 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,360 0,130 1,490 1,505 1,505 1,505 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,670 0,060 0,730 0,737 0,737 0,737 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,850 0,060 0,910 0,919 0,919 0,919 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,040 0,600 0,606 0,606 0,606 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,470 0,060 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,040 0,330 0,333 0,333 0,333 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,180 0,080 1,250 1,263 1,263 1,263 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,490 0,070 0,560 0,566 0,566 0,566 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,180 0,080 1,250 1,263 1,263 1,263 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,590 0,040 0,630 0,636 0,636 0,636 Montenegro Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 10 10 Bars and rods 2,280 N/A 2,280 2,508 2,736 2,964 (K) 7604 10 90 Profiles 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7604 21 00 Hollow profiles 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7604 29 10 Bars and rods 2,280 N/A 2,280 2,508 2,736 2,964 (K) 7604 29 90 Profiles 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7605 Aluminium wire 2,280 N/A 2,280 2,508 2,736 2,964 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7608 Aluminium tubes and pipes 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7610 90 Other 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7610 90 90 Other 2,290 N/A 2,290 2,519 2,748 2,977 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,280 N/A 2,280 2,508 2,736 2,964 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7616 99 10 Cast 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7616 99 90 Other 2,730 N/A 2,730 3,003 3,276 3,549 (K) Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Morocco Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,060 0,900 0,990 1,080 1,170 (A) 2523 21 00 White Portland cement 1,210 0,150 1,360 1,496 1,632 1,768 2523 29 00 Grey Portland cement 0,860 0,100 0,950 1,045 1,140 1,235 2523 90 00 White hydraulic cements 1,250 0,200 1,450 1,595 1,740 1,885 (B) 2523 90 00 Grey hydraulic cements 0,820 0,100 0,910 1,001 1,092 1,183 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,480 0,060 2,540 2,565 2,565 2,565 2814 10 00 Anhydrous ammonia 2,030 0,180 2,200 2,222 2,222 2,222 2814 20 00 Ammonia in aqueous solution 0,610 0,050 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 2,020 0,090 2,100 2,121 2,121 2,121 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,050 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,750 0,050 0,790 0,798 0,798 0,798 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,360 0,140 1,500 1,515 1,515 1,515 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,330 0,140 1,460 1,475 1,475 1,475 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,110 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,300 0,120 1,420 1,434 1,434 1,434 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,530 0,090 1,620 1,636 1,636 1,636 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,350 0,140 2,490 2,515 2,515 2,515 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,010 0,130 2,140 2,161 2,161 2,161 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,010 0,130 2,140 2,161 2,161 2,161 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,880 0,090 3,970 4,010 4,010 4,010 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,970 0,120 2,090 2,111 2,111 2,111 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,480 0,110 1,590 1,606 1,606 1,606 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,520 0,130 1,650 1,667 1,667 1,667 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,750 0,110 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,990 0,130 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,670 0,100 0,770 0,778 0,778 0,778 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,080 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,060 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,360 0,160 1,520 1,535 1,535 1,535 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,120 0,670 0,677 0,677 0,677 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,330 0,100 1,420 1,434 1,434 1,434 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,680 0,070 0,750 0,758 0,758 0,758 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,510 N/A 0,510 0,561 0,612 0,663 (L) 7604 10 10 Bars and rods 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 10 90 Profiles 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7604 21 00 Hollow profiles 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7604 29 10 Bars and rods 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 29 90 Profiles 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7605 Aluminium wire 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7608 Aluminium tubes and pipes 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 90 Other 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 90 90 Other 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7616 99 10 Cast 0,510 N/A 0,510 0,561 0,612 0,663 (L) 7616 99 90 Other 1,190 N/A 1,190 1,309 1,428 1,547 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Mozambique Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 3,198 N/A 3,198 3,518 3,838 4,157 (K) 7603 Aluminium powders and flakes 3,712 N/A 3,712 4,083 4,454 4,825 (K) 7604 10 10 Bars and rods 4,124 N/A 4,124 4,536 4,949 5,361 (K) 7604 10 90 Profiles 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7604 21 00 Hollow profiles 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7604 29 10 Bars and rods 4,124 N/A 4,124 4,536 4,949 5,361 (K) 7604 29 90 Profiles 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7605 Aluminium wire 4,124 N/A 4,124 4,536 4,949 5,361 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7608 Aluminium tubes and pipes 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7610 90 Other 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7610 90 90 Other 4,161 N/A 4,161 4,578 4,994 5,410 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 4,124 N/A 4,124 4,536 4,949 5,361 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 4,986 N/A 4,986 5,485 5,984 6,482 (K) 7616 99 10 Cast 3,712 N/A 3,712 4,083 4,454 4,825 (K) 7616 99 90 Other 4,986 N/A 4,986 5,485 5,984 6,482 (K) Myanmar/Burma Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0,030 1,380 1,518 1,656 1,794 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,350 0,050 1,400 1,540 1,680 1,820 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,280 0,050 1,330 1,463 1,596 1,729 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,140 0,030 2,170 2,192 2,192 2,192 2814 10 00 Anhydrous ammonia 2,100 0,110 2,200 2,222 2,222 2,222 2814 20 00 Ammonia in aqueous solution 0,630 0,030 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 1,800 0,050 1,860 1,879 1,879 1,879 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,480 0,030 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,790 0,030 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,430 0,080 1,520 1,535 1,535 1,535 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,400 0,080 1,480 1,495 1,495 1,495 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,060 0,680 0,687 0,687 0,687 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,220 0,070 1,290 1,303 1,303 1,303 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,370 0,050 1,420 1,434 1,434 1,434 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,110 0,080 2,190 2,212 2,212 2,212 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,820 0,080 1,890 1,909 1,909 1,909 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,820 0,080 1,890 1,909 1,909 1,909 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,340 0,050 3,390 3,424 3,424 3,424 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,770 0,070 1,840 1,858 1,858 1,858 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,400 0,060 1,460 1,475 1,475 1,475 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,480 0,080 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,720 0,060 0,780 0,788 0,788 0,788 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,900 0,080 0,980 0,990 0,990 0,990 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,060 0,670 0,677 0,677 0,677 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,490 0,050 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,040 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,240 0,090 1,330 1,343 1,343 1,343 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,090 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,200 0,060 1,260 1,273 1,273 1,273 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,620 0,040 0,660 0,667 0,667 0,667 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) - - - - - - 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms - N/A - - - - 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - - - - 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - - - - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,350 N/A 1,350 1,485 1,620 1,755 (E) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,130 N/A 3,130 3,443 3,756 4,069 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,130 N/A 3,130 3,443 3,756 4,069 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,130 N/A 3,130 3,443 3,756 4,069 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,130 N/A 3,130 3,443 3,756 4,069 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,130 N/A 3,130 3,443 3,756 4,069 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,130 N/A 3,130 3,443 3,756 4,069 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,130 N/A 3,130 3,443 3,756 4,069 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,130 N/A 3,130 3,443 3,756 4,069 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,130 N/A 3,130 3,443 3,756 4,069 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,130 N/A 3,130 3,443 3,756 4,069 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,130 N/A 3,130 3,443 3,756 4,069 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,130 N/A 3,130 3,443 3,756 4,069 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,130 N/A 3,130 3,443 3,756 4,069 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,130 N/A 3,130 3,443 3,756 4,069 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,130 N/A 3,130 3,443 3,756 4,069 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,130 N/A 3,130 3,443 3,756 4,069 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,130 N/A 3,130 3,443 3,756 4,069 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,130 N/A 3,130 3,443 3,756 4,069 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,130 N/A 3,130 3,443 3,756 4,069 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7224 90 02 Semi-finished products of tool steel 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,530 N/A 4,530 4,983 5,436 5,889 (E) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,400 N/A 3,400 3,740 4,080 4,420 (E) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,530 N/A 4,530 4,983 5,436 5,889 (E) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,400 N/A 3,400 3,740 4,080 4,420 (E) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,400 N/A 3,400 3,740 4,080 4,420 (E)/(H) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,400 N/A 3,400 3,740 4,080 4,420 (E)/(H) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,400 N/A 3,400 3,740 4,080 4,420 (E)/(H) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,400 N/A 3,400 3,740 4,080 4,420 (H) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,400 N/A 3,400 3,740 4,080 4,420 (E)/(H) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 0,520 N/A 0,520 0,572 0,624 0,676 (E) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,510 N/A 2,510 2,761 3,012 3,263 (E) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,350 N/A 1,350 1,485 1,620 1,755 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,130 N/A 3,130 3,443 3,756 4,069 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,130 N/A 3,130 3,443 3,756 4,069 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,130 N/A 3,130 3,443 3,756 4,069 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,130 N/A 3,130 3,443 3,756 4,069 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,130 N/A 3,130 3,443 3,756 4,069 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 0,560 N/A 0,560 0,616 0,672 0,728 (H) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 0,560 N/A 0,560 0,616 0,672 0,728 (E)/(H) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,130 N/A 3,130 3,443 3,756 4,069 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,130 N/A 3,130 3,443 3,756 4,069 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 0,560 N/A 0,560 0,616 0,672 0,728 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,130 N/A 3,130 3,443 3,756 4,069 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,130 N/A 3,130 3,443 3,756 4,069 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 0,560 N/A 0,560 0,616 0,672 0,728 (H) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 0,560 N/A 0,560 0,616 0,672 0,728 (H) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 0,560 N/A 0,560 0,616 0,672 0,728 (H) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,130 N/A 3,130 3,443 3,756 4,069 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,130 N/A 3,130 3,443 3,756 4,069 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 0,560 N/A 0,560 0,616 0,672 0,728 (E) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,350 N/A 1,350 1,485 1,620 1,755 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,350 N/A 1,350 1,485 1,620 1,755 7307 19 90 Cast tube or pipe fittings of steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,640 N/A 2,640 2,904 3,168 3,432 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,640 N/A 2,640 2,904 3,168 3,432 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,640 N/A 2,640 2,904 3,168 3,432 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,640 N/A 2,640 2,904 3,168 3,432 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,700 N/A 2,700 2,970 3,240 3,510 (E) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,100 N/A 3,100 3,410 3,720 4,030 (E) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 0,570 N/A 0,570 0,627 0,684 0,741 (E) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,100 N/A 3,100 3,410 3,720 4,030 (E) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,130 N/A 3,130 3,443 3,756 4,069 (E) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 13 00 Screw hooks and screw rings, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,130 N/A 3,130 3,443 3,756 4,069 (E) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,300 N/A 2,300 2,530 2,760 2,990 (E) 7318 16 Nuts of iron or steel 2,900 N/A 2,900 3,190 3,480 3,770 (E) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 21 00 Spring washers and other lock washers, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,290 N/A 1,290 1,419 1,548 1,677 (E) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 1,040 N/A 1,040 1,144 1,248 1,352 (E) 7318 24 00 Cotters and cotter pins, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7318 29 00 Non-threaded articles, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 20 00 Articles of iron or steel wire, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 30 Ladders and steps, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 50 Reels for cables, piping and the like, of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 96 Sintered articles of iron or steel, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) 7326 90 98 Articles of iron or steel, n.e.s. 0,470 N/A 0,470 0,517 0,564 0,611 (E) Namibia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,880 0 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,880 0,010 0,890 0,979 1,068 1,157 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,840 0,010 0,850 0,935 1,02 1,105 (A) 2523 30 00 Aluminous cement - - - - - - Nepal Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,770 0,070 1,840 1,858 1,858 1,858 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,700 0,060 0,770 0,778 0,778 0,778 2834 21 00 Nitrate of potassium 1,610 0,090 1,700 1,717 1,717 1,717 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,520 0,050 0,570 0,576 0,576 0,576 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,860 0,050 0,910 0,919 0,919 0,919 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,570 0,140 1,720 1,737 1,737 1,737 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,540 0,140 1,680 1,697 1,697 1,697 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,090 0,770 0,778 0,778 0,778 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,170 0,100 1,270 1,283 1,283 1,283 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,220 0,080 1,310 1,323 1,323 1,323 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,880 0,130 2,010 2,030 2,030 2,030 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,110 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,110 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,760 0,110 2,870 2,899 2,899 2,899 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,580 0,110 1,690 1,707 1,707 1,707 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,100 1,440 1,454 1,454 1,454 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,120 1,610 1,626 1,626 1,626 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,080 0,780 0,788 0,788 0,788 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,090 0,910 0,919 0,919 0,919 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,070 0,630 0,636 0,636 0,636 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,070 0,610 0,616 0,616 0,616 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,350 0,050 0,400 0,404 0,404 0,404 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,120 0,110 1,240 1,252 1,252 1,252 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,630 0,110 0,740 0,747 0,747 0,747 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,080 1,170 1,182 1,182 1,182 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,050 0,610 0,616 0,616 0,616 New Zealand Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,870 0,010 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,890 0,030 0,920 1,012 1,104 1,196 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,850 0,030 0,880 0,968 1,056 1,144 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,590 0,030 1,620 1,636 1,636 1,636 2814 10 00 Anhydrous ammonia 1,760 0,040 1,800 1,818 1,818 1,818 2814 20 00 Ammonia in aqueous solution 0,530 0,010 0,540 0,545 0,545 0,545 2834 21 00 Nitrate of potassium 1,380 0,030 1,420 1,434 1,434 1,434 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,400 0,010 0,420 0,424 0,424 0,424 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,670 0,010 0,680 0,687 0,687 0,687 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,220 0,040 1,250 1,263 1,263 1,263 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,190 0,040 1,230 1,242 1,242 1,242 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,030 0,550 0,556 0,556 0,556 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 0,970 0,040 1 1,010 1,010 1,010 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,050 0,030 1,090 1,101 1,101 1,101 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,050 1,670 1,687 1,687 1,687 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,400 0,040 1,450 1,465 1,465 1,465 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,400 0,040 1,450 1,465 1,465 1,465 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,480 0,050 2,530 2,555 2,555 2,555 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,360 0,040 1,400 1,414 1,414 1,414 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,110 0,040 1,140 1,151 1,151 1,151 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,210 0,040 1,240 1,252 1,252 1,252 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,570 0,030 0,610 0,616 0,616 0,616 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,040 0,750 0,758 0,758 0,758 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,030 0,510 0,515 0,515 0,515 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,420 0,020 0,440 0,444 0,444 0,444 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,270 0,020 0,290 0,293 0,293 0,293 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 0,960 0,050 1,010 1,020 1,020 1,020 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,490 0,060 0,550 0,556 0,556 0,556 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,930 0,030 0,960 0,970 0,970 0,970 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,480 0,020 0,500 0,505 0,505 0,505 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,070 0,040 0,100 0,110 0,120 0,130 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,310 N/A 2,310 2,541 2,772 3,003 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - - - - 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - - - - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,320 N/A 2,320 2,552 2,784 3,016 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,360 N/A 3,360 3,696 4,032 4,368 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,380 N/A 3,380 3,718 4,056 4,394 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,380 N/A 3,380 3,718 4,056 4,394 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,360 N/A 3,360 3,696 4,032 4,368 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,380 N/A 3,380 3,718 4,056 4,394 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,360 N/A 3,360 3,696 4,032 4,368 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,380 N/A 3,380 3,718 4,056 4,394 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,390 N/A 3,390 3,729 4,068 4,407 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,390 N/A 3,390 3,729 4,068 4,407 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,390 N/A 3,390 3,729 4,068 4,407 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,390 N/A 3,390 3,729 4,068 4,407 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,390 N/A 3,390 3,729 4,068 4,407 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,390 N/A 3,390 3,729 4,068 4,407 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,380 N/A 3,380 3,718 4,056 4,394 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,380 N/A 3,380 3,718 4,056 4,394 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,390 N/A 3,390 3,729 4,068 4,407 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,390 N/A 3,390 3,729 4,068 4,407 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,360 N/A 3,360 3,696 4,032 4,368 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,360 N/A 3,360 3,696 4,032 4,368 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,360 N/A 3,360 3,696 4,032 4,368 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,360 N/A 3,360 3,696 4,032 4,368 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,360 N/A 3,360 3,696 4,032 4,368 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,360 N/A 3,360 3,696 4,032 4,368 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,360 N/A 3,360 3,696 4,032 4,368 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 02 Semi-finished products of tool steel 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,660 N/A 4,660 5,126 5,592 6,058 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,520 N/A 3,520 3,872 4,224 4,576 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,660 N/A 4,660 5,126 5,592 6,058 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,520 N/A 3,520 3,872 4,224 4,576 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,520 N/A 3,520 3,872 4,224 4,576 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,530 N/A 3,530 3,883 4,236 4,589 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,060 N/A 3,060 3,366 3,672 3,978 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,310 N/A 2,310 2,541 2,772 3,003 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,360 N/A 3,360 3,696 4,032 4,368 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,360 N/A 3,360 3,696 4,032 4,368 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,360 N/A 3,360 3,696 4,032 4,368 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,360 N/A 3,360 3,696 4,032 4,368 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,360 N/A 3,360 3,696 4,032 4,368 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,360 N/A 2,360 2,596 2,832 3,068 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,360 N/A 2,360 2,596 2,832 3,068 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,390 N/A 3,390 3,729 4,068 4,407 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,390 N/A 3,390 3,729 4,068 4,407 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,420 N/A 2,420 2,662 2,904 3,146 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,390 N/A 3,390 3,729 4,068 4,407 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,380 N/A 3,380 3,718 4,056 4,394 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,410 N/A 2,410 2,651 2,892 3,133 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,400 N/A 2,400 2,640 2,880 3,120 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,410 N/A 2,410 2,651 2,892 3,133 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,390 N/A 3,390 3,729 4,068 4,407 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,390 N/A 3,390 3,729 4,068 4,407 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,310 N/A 2,310 2,541 2,772 3,003 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,310 N/A 2,310 2,541 2,772 3,003 7307 19 90 Cast tube or pipe fittings of steel 2,410 N/A 2,410 2,651 2,892 3,133 7307 21 00 Flanges of stainless steel (excl. cast products) 2,820 N/A 2,820 3,102 3,384 3,666 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,820 N/A 2,820 3,102 3,384 3,666 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,820 N/A 2,820 3,102 3,384 3,666 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,820 N/A 2,820 3,102 3,384 3,666 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,900 N/A 2,900 3,190 3,480 3,770 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,430 N/A 2,430 2,673 2,916 3,159 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,020 N/A 3,020 3,322 3,624 3,926 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,360 N/A 3,360 3,696 4,032 4,368 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,360 N/A 3,360 3,696 4,032 4,368 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,820 N/A 2,820 3,102 3,384 3,666 (C) 7318 16 Nuts of iron or steel 3,020 N/A 3,020 3,322 3,624 3,926 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,470 N/A 2,470 2,717 2,964 3,211 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 30 Ladders and steps, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,430 N/A 2,430 2,673 2,916 3,159 (C) Nicaragua Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,810 0,070 1,880 1,899 1,899 1,899 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,680 0,070 0,750 0,758 0,758 0,758 2834 21 00 Nitrate of potassium 1,620 0,110 1,730 1,747 1,747 1,747 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,060 0,570 0,576 0,576 0,576 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,060 0,900 0,909 0,909 0,909 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,180 1,700 1,717 1,717 1,717 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,170 1,670 1,687 1,687 1,687 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,130 0,790 0,798 0,798 0,798 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,140 1,300 1,313 1,313 1,313 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,110 1,340 1,353 1,353 1,353 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,900 0,170 2,060 2,081 2,081 2,081 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,160 1,800 1,818 1,818 1,818 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,640 0,160 1,800 1,818 1,818 1,818 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,820 0,120 2,940 2,969 2,969 2,969 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,150 1,740 1,757 1,757 1,757 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,330 0,140 1,470 1,485 1,485 1,485 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,160 1,630 1,646 1,646 1,646 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,130 0,820 0,828 0,828 0,828 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,830 0,150 0,980 0,990 0,990 0,990 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,120 0,680 0,687 0,687 0,687 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,100 0,630 0,636 0,636 0,636 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,080 0,410 0,414 0,414 0,414 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,130 0,190 1,320 1,333 1,333 1,333 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,140 0,750 0,758 0,758 0,758 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,120 1,210 1,222 1,222 1,222 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,080 0,640 0,646 0,646 0,646 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7604 10 10 Bars and rods 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7604 10 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 21 00 Hollow profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 10 Bars and rods 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7604 29 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7605 Aluminium wire 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7608 Aluminium tubes and pipes 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 99 10 Cast 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7616 99 90 Other 1,150 N/A 1,150 1,265 1,380 1,495 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Niger Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,240 0,080 1,320 1,452 1,584 1,716 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,220 0,130 1,350 1,485 1,620 1,755 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,160 0,130 1,290 1,419 1,548 1,677 (A) 2523 30 00 Aluminous cement - - - - - - Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Nigeria Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,240 0,030 1,280 1,408 1,536 1,664 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,240 0,050 1,300 1,430 1,560 1,690 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,180 0,060 1,240 1,364 1,488 1,612 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,610 0,030 1,650 1,667 1,667 1,667 2814 10 00 Anhydrous ammonia 2,010 0,100 2,110 2,131 2,131 2,131 2814 20 00 Ammonia in aqueous solution 0,600 0,030 0,630 0,636 0,636 0,636 2834 21 00 Nitrate of potassium 1,450 0,050 1,500 1,515 1,515 1,515 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,030 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,030 0,790 0,798 0,798 0,798 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,380 0,080 1,460 1,475 1,475 1,475 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,350 0,080 1,430 1,444 1,444 1,444 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,060 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,040 0,070 1,110 1,121 1,121 1,121 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,100 0,050 1,150 1,162 1,162 1,162 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,080 1,770 1,788 1,788 1,788 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,070 1,540 1,555 1,555 1,555 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,070 1,540 1,555 1,555 1,555 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,520 0,050 2,570 2,596 2,596 2,596 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,420 0,070 1,490 1,505 1,505 1,505 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,200 0,060 1,260 1,273 1,273 1,273 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,320 0,070 1,400 1,414 1,414 1,414 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,620 0,060 0,680 0,687 0,687 0,687 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,750 0,070 0,820 0,828 0,828 0,828 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,060 0,570 0,576 0,576 0,576 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,470 0,040 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,010 0,090 1,100 1,111 1,111 1,111 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,080 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,050 1,030 1,040 1,040 1,040 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,510 0,040 0,540 0,545 0,545 0,545 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,100 N/A 1,100 1,210 1,320 1,430 (L) 7604 10 10 Bars and rods 1,330 N/A 1,330 1,463 1,596 1,729 (L) 7604 10 90 Profiles 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7604 21 00 Hollow profiles 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7604 29 10 Bars and rods 1,330 N/A 1,330 1,463 1,596 1,729 (L) 7604 29 90 Profiles 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7605 Aluminium wire 1,330 N/A 1,330 1,463 1,596 1,729 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7608 Aluminium tubes and pipes 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7610 90 Other 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7610 90 90 Other 1,340 N/A 1,340 1,474 1,608 1,742 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,330 N/A 1,330 1,463 1,596 1,729 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,790 N/A 1,790 1,969 2,148 2,327 (L) 7616 99 10 Cast 1,100 N/A 1,100 1,210 1,320 1,430 (L) 7616 99 90 Other 1,790 N/A 1,790 1,969 2,148 2,327 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 North Korea Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0,040 1,390 1,529 1,668 1,807 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,360 0,070 1,420 1,562 1,704 1,846 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,290 0,070 1,360 1,496 1,632 1,768 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,080 0,050 2,130 2,151 2,151 2,151 2814 10 00 Anhydrous ammonia 2,050 0,150 2,200 2,222 2,222 2,222 2814 20 00 Ammonia in aqueous solution 0,620 0,040 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 1,750 0,070 1,820 1,838 1,838 1,838 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,040 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,040 0,770 0,778 0,778 0,778 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,340 0,120 1,450 1,465 1,465 1,465 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,310 0,110 1,420 1,434 1,434 1,434 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,090 0,680 0,687 0,687 0,687 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,180 0,100 1,270 1,283 1,283 1,283 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,330 0,070 1,400 1,414 1,414 1,414 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,040 0,110 2,160 2,182 2,182 2,182 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,100 1,850 1,869 1,869 1,869 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,100 1,850 1,869 1,869 1,869 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,250 0,070 3,320 3,353 3,353 3,353 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,710 0,100 1,810 1,828 1,828 1,828 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,090 1,430 1,444 1,444 1,444 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,410 0,110 1,520 1,535 1,535 1,535 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,090 0,780 0,788 0,788 0,788 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,870 0,110 0,970 0,980 0,980 0,980 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,080 0,670 0,677 0,677 0,677 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,060 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,050 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,190 0,130 1,320 1,333 1,333 1,333 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,100 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,160 0,080 1,240 1,252 1,252 1,252 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,600 0,060 0,650 0,657 0,657 0,657 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 North Macedonia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,050 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,870 0,090 0,960 1,056 1,152 1,248 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,830 0,090 0,920 1,012 1,104 1,196 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,740 0,060 2,790 2,818 2,818 2,818 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,050 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 2,190 0,080 2,270 2,293 2,293 2,293 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,040 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,720 0,040 0,770 0,778 0,778 0,778 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,310 0,140 1,450 1,465 1,465 1,465 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,280 0,130 1,420 1,434 1,434 1,434 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,100 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,380 0,110 1,500 1,515 1,515 1,515 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,650 0,090 1,740 1,757 1,757 1,757 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,540 0,130 2,670 2,697 2,697 2,697 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,120 2,270 2,293 2,293 2,293 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,120 2,270 2,293 2,293 2,293 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,270 0,090 4,360 4,404 4,404 4,404 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,130 0,120 2,240 2,262 2,262 2,262 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,550 0,100 1,660 1,677 1,677 1,677 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,560 0,120 1,680 1,697 1,697 1,697 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,790 0,100 0,890 0,899 0,899 0,899 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,120 1,170 1,182 1,182 1,182 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,090 0,800 0,808 0,808 0,808 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,080 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,060 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,440 0,150 1,590 1,606 1,606 1,606 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,110 0,670 0,677 0,677 0,677 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,090 1,520 1,535 1,535 1,535 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,060 0,790 0,798 0,798 0,798 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) - - - - - - 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms - N/A - - - - 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,630 N/A 1,630 1,793 1,956 2,119 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,510 N/A 1,510 1,661 1,812 1,963 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,530 N/A 1,530 1,683 1,836 1,989 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,530 N/A 1,530 1,683 1,836 1,989 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,530 N/A 1,530 1,683 1,836 1,989 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,530 N/A 1,530 1,683 1,836 1,989 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 1,510 N/A 1,510 1,661 1,812 1,963 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,530 N/A 1,530 1,683 1,836 1,989 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 1,510 N/A 1,510 1,661 1,812 1,963 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,530 N/A 1,530 1,683 1,836 1,989 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 1,510 N/A 1,510 1,661 1,812 1,963 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 1,530 N/A 1,530 1,683 1,836 1,989 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,530 N/A 1,530 1,683 1,836 1,989 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,530 N/A 1,530 1,683 1,836 1,989 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,530 N/A 1,530 1,683 1,836 1,989 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 1,510 N/A 1,510 1,661 1,812 1,963 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,530 N/A 1,530 1,683 1,836 1,989 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 1,510 N/A 1,510 1,661 1,812 1,963 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,530 N/A 1,530 1,683 1,836 1,989 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 1,510 N/A 1,510 1,661 1,812 1,963 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 1,530 N/A 1,530 1,683 1,836 1,989 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 1,530 N/A 1,530 1,683 1,836 1,989 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 1,530 N/A 1,530 1,683 1,836 1,989 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,530 N/A 1,530 1,683 1,836 1,989 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 1,530 N/A 1,530 1,683 1,836 1,989 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 1,530 N/A 1,530 1,683 1,836 1,989 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 1,530 N/A 1,530 1,683 1,836 1,989 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 1,530 N/A 1,530 1,683 1,836 1,989 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 1,530 N/A 1,530 1,683 1,836 1,989 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 1,530 N/A 1,530 1,683 1,836 1,989 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,530 N/A 1,530 1,683 1,836 1,989 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 1,530 N/A 1,530 1,683 1,836 1,989 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 1,510 N/A 1,510 1,661 1,812 1,963 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 1,530 N/A 1,530 1,683 1,836 1,989 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 1,530 N/A 1,530 1,683 1,836 1,989 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 1,530 N/A 1,530 1,683 1,836 1,989 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 1,530 N/A 1,530 1,683 1,836 1,989 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 1,530 N/A 1,530 1,683 1,836 1,989 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 1,922 N/A 1,922 2,114 2,306 2,499 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 1,530 N/A 1,530 1,683 1,836 1,989 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 1,530 N/A 1,530 1,683 1,836 1,989 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 1,530 N/A 1,530 1,683 1,836 1,989 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 1,530 N/A 1,530 1,683 1,836 1,989 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,900 N/A 2,900 3,190 3,480 3,770 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 2,910 N/A 2,910 3,201 3,492 3,783 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 2,910 N/A 2,910 3,201 3,492 3,783 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 2,900 N/A 2,900 3,190 3,480 3,770 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 2,910 N/A 2,910 3,201 3,492 3,783 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 2,900 N/A 2,900 3,190 3,480 3,770 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 2,910 N/A 2,910 3,201 3,492 3,783 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,910 N/A 2,910 3,201 3,492 3,783 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 2,910 N/A 2,910 3,201 3,492 3,783 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 2,910 N/A 2,910 3,201 3,492 3,783 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 2,910 N/A 2,910 3,201 3,492 3,783 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,910 N/A 2,910 3,201 3,492 3,783 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 2,910 N/A 2,910 3,201 3,492 3,783 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 2,910 N/A 2,910 3,201 3,492 3,783 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 2,910 N/A 2,910 3,201 3,492 3,783 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 2,910 N/A 2,910 3,201 3,492 3,783 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 2,900 N/A 2,900 3,190 3,480 3,770 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 2,910 N/A 2,910 3,201 3,492 3,783 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 2,910 N/A 2,910 3,201 3,492 3,783 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,420 N/A 3,420 3,762 4,104 4,446 7224 90 02 Semi-finished products of tool steel 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,420 N/A 3,420 3,762 4,104 4,446 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,440 N/A 3,440 3,784 4,128 4,472 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,420 N/A 3,420 3,762 4,104 4,446 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,550 N/A 4,550 5,005 5,460 5,915 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,440 N/A 3,440 3,784 4,128 4,472 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,440 N/A 3,440 3,784 4,128 4,472 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,550 N/A 4,550 5,005 5,460 5,915 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,440 N/A 3,440 3,784 4,128 4,472 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,440 N/A 3,440 3,784 4,128 4,472 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,440 N/A 3,440 3,784 4,128 4,472 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,440 N/A 3,440 3,784 4,128 4,472 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,440 N/A 3,440 3,784 4,128 4,472 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,440 N/A 3,440 3,784 4,128 4,472 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,440 N/A 3,440 3,784 4,128 4,472 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,440 N/A 3,440 3,784 4,128 4,472 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 1,550 N/A 1,550 1,705 1,860 2,015 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,580 N/A 2,580 2,838 3,096 3,354 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,640 N/A 1,640 1,804 1,968 2,132 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 2,910 N/A 2,910 3,201 3,492 3,783 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 1,560 N/A 1,560 1,716 1,872 2,028 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 2,910 N/A 2,910 3,201 3,492 3,783 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 1,560 N/A 1,560 1,716 1,872 2,028 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 2,910 N/A 2,910 3,201 3,492 3,783 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 1,560 N/A 1,560 1,716 1,872 2,028 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 1,560 N/A 1,560 1,716 1,872 2,028 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 1,560 N/A 1,560 1,716 1,872 2,028 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,910 N/A 2,910 3,201 3,492 3,783 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 2,910 N/A 2,910 3,201 3,492 3,783 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,570 N/A 1,570 1,727 1,884 2,041 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,570 N/A 1,570 1,727 1,884 2,041 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 1,560 N/A 1,560 1,716 1,872 2,028 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 1,570 N/A 1,570 1,727 1,884 2,041 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,910 N/A 2,910 3,201 3,492 3,783 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,898 N/A 1,898 2,088 2,278 2,467 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,910 N/A 2,910 3,201 3,492 3,783 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 1,898 N/A 1,898 2,088 2,278 2,467 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 1,898 N/A 1,898 2,088 2,278 2,467 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,910 N/A 2,910 3,201 3,492 3,783 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,910 N/A 2,910 3,201 3,492 3,783 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 1,898 N/A 1,898 2,088 2,278 2,467 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 1,898 N/A 1,898 2,088 2,278 2,467 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 1,898 N/A 1,898 2,088 2,278 2,467 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 2,910 N/A 2,910 3,201 3,492 3,783 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 1,898 N/A 1,898 2,088 2,278 2,467 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 1,898 N/A 1,898 2,088 2,278 2,467 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,910 N/A 2,910 3,201 3,492 3,783 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 1,898 N/A 1,898 2,088 2,278 2,467 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 1,898 N/A 1,898 2,088 2,278 2,467 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,630 N/A 1,630 1,793 1,956 2,119 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,630 N/A 1,630 1,793 1,956 2,119 7307 19 90 Cast tube or pipe fittings of steel 1,510 N/A 1,510 1,661 1,812 1,963 7307 21 00 Flanges of stainless steel (excl. cast products) 2,630 N/A 2,630 2,893 3,156 3,419 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,630 N/A 2,630 2,893 3,156 3,419 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,630 N/A 2,630 2,893 3,156 3,419 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,630 N/A 2,630 2,893 3,156 3,419 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 1,530 N/A 1,530 1,683 1,836 1,989 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 1,530 N/A 1,530 1,683 1,836 1,989 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 1,530 N/A 1,530 1,683 1,836 1,989 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 1,530 N/A 1,530 1,683 1,836 1,989 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,690 N/A 2,690 2,959 3,228 3,497 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,900 N/A 2,900 3,190 3,480 3,770 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 1,580 N/A 1,580 1,738 1,896 2,054 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,900 N/A 2,900 3,190 3,480 3,770 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7318 12 10 Wood screws of stainless steel (excl. coach screws) 2,910 N/A 2,910 3,201 3,492 3,783 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 1,530 N/A 1,530 1,683 1,836 1,989 7318 13 00 Screw hooks and screw rings, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 2,910 N/A 2,910 3,201 3,492 3,783 7318 14 91 Spaced-thread screws of iron or steel other than stainless 1,530 N/A 1,530 1,683 1,836 1,989 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 1,530 N/A 1,530 1,683 1,836 1,989 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,480 N/A 2,480 2,728 2,976 3,224 7318 16 Nuts of iron or steel 2,860 N/A 2,860 3,146 3,432 3,718 7318 19 00 Threaded articles, of iron or steel, n.e.s. 1,530 N/A 1,530 1,683 1,836 1,989 7318 21 00 Spring washers and other lock washers, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,830 N/A 1,830 2,013 2,196 2,379 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 1,740 N/A 1,740 1,914 2,088 2,262 7318 24 00 Cotters and cotter pins, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7318 29 00 Non-threaded articles, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 1,510 N/A 1,510 1,661 1,812 1,963 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 1,510 N/A 1,510 1,661 1,812 1,963 7326 20 00 Articles of iron or steel wire, n.e.s. 1,530 N/A 1,530 1,683 1,836 1,989 7326 90 30 Ladders and steps, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7326 90 50 Reels for cables, piping and the like, of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 1,530 N/A 1,530 1,683 1,836 1,989 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 1,510 N/A 1,510 1,661 1,812 1,963 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 1,510 N/A 1,510 1,661 1,812 1,963 7326 90 96 Sintered articles of iron or steel, n.e.s. 1,510 N/A 1,510 1,661 1,812 1,963 7326 90 98 Articles of iron or steel, n.e.s. 1,530 N/A 1,530 1,683 1,836 1,989 Oman Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,830 0,030 0,860 0,946 1,032 1,118 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,860 0,060 0,920 1,012 1,104 1,196 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Pakistan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,250 0,040 1,290 1,419 1,548 1,677 (B) 2523 10 00 Grey clinker 1,280 0,020 1,300 1,430 1,560 1,690 (A) 2523 21 00 White Portland cement 1,290 0,120 1,410 1,551 1,692 1,833 2523 29 00 Grey Portland cement 1,280 0,050 1,320 1,452 1,584 1,716 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,770 0,040 1,800 1,818 1,818 1,818 2814 10 00 Anhydrous ammonia 2,340 0,120 2,460 2,485 2,485 2,485 2814 20 00 Ammonia in aqueous solution 0,700 0,040 0,740 0,747 0,747 0,747 2834 21 00 Nitrate of potassium 1,610 0,050 1,660 1,677 1,677 1,677 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,520 0,030 0,550 0,556 0,556 0,556 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,860 0,030 0,890 0,899 0,899 0,899 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,560 0,090 1,650 1,667 1,667 1,667 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,530 0,090 1,620 1,636 1,636 1,636 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,060 0,750 0,758 0,758 0,758 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,070 1,240 1,252 1,252 1,252 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,220 0,060 1,280 1,293 1,293 1,293 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,880 0,080 1,960 1,980 1,980 1,980 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,080 1,700 1,717 1,717 1,717 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,080 1,700 1,717 1,717 1,717 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,760 0,060 2,820 2,848 2,848 2,848 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,580 0,080 1,650 1,667 1,667 1,667 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,340 0,070 1,400 1,414 1,414 1,414 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,480 0,080 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,060 0,760 0,768 0,768 0,768 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,080 0,900 0,909 0,909 0,909 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,060 0,620 0,626 0,626 0,626 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,050 0,600 0,606 0,606 0,606 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,350 0,040 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,120 0,100 1,210 1,222 1,222 1,222 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,630 0,090 0,720 0,727 0,727 0,727 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,060 1,140 1,151 1,151 1,151 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,040 0,600 0,606 0,606 0,606 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 10 10 Bars and rods 1,520 N/A 1,520 1,672 1,824 1,976 (L) 7604 10 90 Profiles 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7604 21 00 Hollow profiles 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7604 29 10 Bars and rods 1,520 N/A 1,520 1,672 1,824 1,976 (L) 7604 29 90 Profiles 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7605 Aluminium wire 1,520 N/A 1,520 1,672 1,824 1,976 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7608 Aluminium tubes and pipes 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7610 90 Other 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7610 90 90 Other 1,530 N/A 1,530 1,683 1,836 1,989 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,520 N/A 1,520 1,672 1,824 1,976 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,970 N/A 1,970 2,167 2,364 2,561 (L) 7616 99 10 Cast 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7616 99 90 Other 1,970 N/A 1,970 2,167 2,364 2,561 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Papua New Guinea Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Panama Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,870 0,020 0,890 0,979 1,068 1,157 (A) 2523 21 00 White Portland cement 1,220 0,130 1,350 1,485 1,620 1,755 2523 29 00 Grey Portland cement 0,890 0,040 0,940 1,034 1,128 1,222 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,830 0,030 1,860 1,879 1,879 1,879 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,680 0,030 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 1,600 0,040 1,640 1,656 1,656 1,656 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,430 0,020 0,450 0,455 0,455 0,455 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,710 0,020 0,730 0,737 0,737 0,737 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,280 0,060 1,350 1,364 1,364 1,364 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,260 0,060 1,320 1,333 1,333 1,333 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,030 0,610 0,616 0,616 0,616 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,090 0,040 1,120 1,131 1,131 1,131 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,190 0,030 1,220 1,232 1,232 1,232 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,840 0,050 1,880 1,899 1,899 1,899 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,540 0,040 1,580 1,596 1,596 1,596 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,540 0,040 1,580 1,596 1,596 1,596 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,850 0,050 2,900 2,929 2,929 2,929 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,540 0,040 1,580 1,596 1,596 1,596 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,240 0,040 1,280 1,293 1,293 1,293 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,310 0,050 1,360 1,374 1,374 1,374 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,630 0,020 0,650 0,657 0,657 0,657 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,760 0,020 0,780 0,788 0,788 0,788 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,010 0,520 0,525 0,525 0,525 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,020 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,010 0,320 0,323 0,323 0,323 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,040 0,030 1,070 1,081 1,081 1,081 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,520 0,020 0,540 0,545 0,545 0,545 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,040 0,030 1,070 1,081 1,081 1,081 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,520 0,010 0,540 0,545 0,545 0,545 Paraguay Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,910 0 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,910 0 0,910 1,001 1,092 1,183 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,910 0,020 1,930 1,949 1,949 1,949 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,690 0,030 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 1,660 0,030 1,690 1,707 1,707 1,707 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,430 0,020 0,450 0,455 0,455 0,455 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,720 0,020 0,730 0,737 0,737 0,737 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,300 0,050 1,350 1,364 1,364 1,364 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,270 0,050 1,320 1,333 1,333 1,333 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,020 0,610 0,616 0,616 0,616 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,120 0,030 1,150 1,162 1,162 1,162 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,240 0,020 1,260 1,273 1,273 1,273 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,910 0,040 1,940 1,959 1,959 1,959 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,030 1,620 1,636 1,636 1,636 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,030 1,620 1,636 1,636 1,636 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,980 0,040 3,020 3,050 3,050 3,050 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,590 0,030 1,620 1,636 1,636 1,636 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,280 0,030 1,310 1,323 1,323 1,323 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,340 0,040 1,380 1,394 1,394 1,394 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,650 0,020 0,670 0,677 0,677 0,677 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,780 0,020 0,800 0,808 0,808 0,808 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,010 0,530 0,535 0,535 0,535 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,020 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,010 0,320 0,323 0,323 0,323 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,080 0,020 1,100 1,111 1,111 1,111 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,520 0,020 0,540 0,545 0,545 0,545 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,020 1,100 1,111 1,111 1,111 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,540 0,010 0,550 0,556 0,556 0,556 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Peru Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,230 0,050 0,280 0,308 0,336 0,364 (A) 2523 10 00 White clinker 1,290 0,020 1,310 1,441 1,572 1,703 (B) 2523 10 00 Grey clinker 1,090 0,020 1,110 1,221 1,332 1,443 (A) 2523 21 00 White Portland cement 1,250 0,110 1,360 1,496 1,632 1,768 2523 29 00 Grey Portland cement 1,070 0,030 1,110 1,221 1,332 1,443 2523 90 00 White hydraulic cements 1,280 0,130 1,410 1,551 1,692 1,833 (B) 2523 90 00 Grey hydraulic cements 1,020 0,040 1,060 1,166 1,272 1,378 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,900 0,020 1,920 1,939 1,939 1,939 2814 10 00 Anhydrous ammonia 2,260 0,060 2,330 2,353 2,353 2,353 2814 20 00 Ammonia in aqueous solution 0,680 0,020 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 1,680 0,030 1,710 1,727 1,727 1,727 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,510 0,020 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,020 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,530 0,050 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,500 0,050 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,040 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,190 0,040 1,230 1,242 1,242 1,242 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,280 0,030 1,310 1,323 1,323 1,323 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,960 0,050 2,010 2,030 2,030 2,030 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,040 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,040 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,960 0,030 3 3,030 3,030 3,030 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,650 0,040 1,690 1,707 1,707 1,707 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,360 0,040 1,400 1,414 1,414 1,414 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,490 0,040 1,540 1,555 1,555 1,555 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,040 0,740 0,747 0,747 0,747 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,850 0,040 0,900 0,909 0,909 0,909 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,030 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,030 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,020 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,160 0,050 1,210 1,222 1,222 1,222 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,060 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,130 0,030 1,160 1,172 1,172 1,172 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,580 0,020 0,600 0,606 0,606 0,606 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,840 N/A 1,840 2,024 2,208 2,392 (L) 7604 10 10 Bars and rods 2,060 N/A 2,060 2,266 2,472 2,678 (L) 7604 10 90 Profiles 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7604 21 00 Hollow profiles 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7604 29 10 Bars and rods 2,060 N/A 2,060 2,266 2,472 2,678 (L) 7604 29 90 Profiles 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7605 Aluminium wire 2,060 N/A 2,060 2,266 2,472 2,678 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7608 Aluminium tubes and pipes 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7610 90 Other 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7610 90 90 Other 2,080 N/A 2,080 2,288 2,496 2,704 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,060 N/A 2,060 2,266 2,472 2,678 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,520 N/A 2,520 2,772 3,024 3,276 (L) 7616 99 10 Cast 1,840 N/A 1,840 2,024 2,208 2,392 (L) 7616 99 90 Other 2,520 N/A 2,520 2,772 3,024 3,276 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Philippines Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,330 0,050 1,380 1,518 1,656 1,794 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,270 0,090 1,360 1,496 1,632 1,768 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,210 0,090 1,300 1,430 1,560 1,690 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,180 0,060 2,250 2,273 2,273 2,273 2814 10 00 Anhydrous ammonia 2,130 0,200 2,330 2,353 2,353 2,353 2814 20 00 Ammonia in aqueous solution 0,640 0,060 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 1,840 0,100 1,940 1,959 1,959 1,959 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,480 0,050 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,800 0,050 0,850 0,859 0,859 0,859 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,450 0,160 1,610 1,626 1,626 1,626 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,420 0,150 1,570 1,586 1,586 1,586 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,630 0,120 0,740 0,747 0,747 0,747 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,240 0,130 1,370 1,384 1,384 1,384 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,400 0,100 1,500 1,515 1,515 1,515 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,150 2,300 2,323 2,323 2,323 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,850 0,140 1,990 2,010 2,010 2,010 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,850 0,140 1,990 2,010 2,010 2,010 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,410 0,100 3,510 3,545 3,545 3,545 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,800 0,130 1,940 1,959 1,959 1,959 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,420 0,120 1,540 1,555 1,555 1,555 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,510 0,140 1,650 1,667 1,667 1,667 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,730 0,120 0,850 0,859 0,859 0,859 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,920 0,140 1,060 1,071 1,071 1,071 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,110 0,730 0,737 0,737 0,737 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,090 0,590 0,596 0,596 0,596 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,070 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,260 0,180 1,440 1,454 1,454 1,454 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,130 0,710 0,717 0,717 0,717 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,220 0,110 1,330 1,343 1,343 1,343 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,630 0,080 0,700 0,707 0,707 0,707 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,490 N/A 0,490 0,539 0,588 0,637 (L) 7604 10 10 Bars and rods 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 10 90 Profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 21 00 Hollow profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 29 10 Bars and rods 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 90 Profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7605 Aluminium wire 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7608 Aluminium tubes and pipes 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 Other 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 90 Other 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7616 99 10 Cast 0,490 N/A 0,490 0,539 0,588 0,637 (L) 7616 99 90 Other 1,170 N/A 1,170 1,287 1,404 1,521 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,120 0,070 0,190 0,209 0,228 0,247 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms - N/A - - - - 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - - - - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,650 N/A 1,650 1,815 1,980 2,145 (E) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,920 N/A 2,920 3,212 3,504 3,796 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 2,920 N/A 2,920 3,212 3,504 3,796 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 2,920 N/A 2,920 3,212 3,504 3,796 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 2,920 N/A 2,920 3,212 3,504 3,796 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 2,920 N/A 2,920 3,212 3,504 3,796 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 2,920 N/A 2,920 3,212 3,504 3,796 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,920 N/A 2,920 3,212 3,504 3,796 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 2,920 N/A 2,920 3,212 3,504 3,796 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 2,920 N/A 2,920 3,212 3,504 3,796 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 2,920 N/A 2,920 3,212 3,504 3,796 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,920 N/A 2,920 3,212 3,504 3,796 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 2,930 N/A 2,930 3,223 3,516 3,809 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 2,930 N/A 2,930 3,223 3,516 3,809 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 2,930 N/A 2,930 3,223 3,516 3,809 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 2,930 N/A 2,930 3,223 3,516 3,809 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 2,920 N/A 2,920 3,212 3,504 3,796 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 2,930 N/A 2,930 3,223 3,516 3,809 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 2,930 N/A 2,930 3,223 3,516 3,809 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 02 Semi-finished products of tool steel 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 3,950 N/A 3,950 4,345 4,740 5,135 (E) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 2,650 N/A 2,650 2,915 3,180 3,445 (E) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 3,950 N/A 3,950 4,345 4,740 5,135 (E) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 2,650 N/A 2,650 2,915 3,180 3,445 (E) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 2,660 N/A 2,660 2,926 3,192 3,458 (E)/(H) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,660 N/A 2,660 2,926 3,192 3,458 (H) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,660 N/A 2,660 2,926 3,192 3,458 (H) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,660 N/A 2,660 2,926 3,192 3,458 (H) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,660 N/A 2,660 2,926 3,192 3,458 (E)/(H) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,650 N/A 2,650 2,915 3,180 3,445 (H) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,660 N/A 2,660 2,926 3,192 3,458 (E)/(H) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,660 N/A 2,660 2,926 3,192 3,458 (H) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 2,660 N/A 2,660 2,926 3,192 3,458 (H) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 2,660 N/A 2,660 2,926 3,192 3,458 (H) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 2,660 N/A 2,660 2,926 3,192 3,458 (E)/(H) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 0,790 N/A 0,790 0,869 0,948 1,027 (E) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,260 N/A 2,260 2,486 2,712 2,938 (E) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,650 N/A 1,650 1,815 1,980 2,145 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 2,920 N/A 2,920 3,212 3,504 3,796 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 2,920 N/A 2,920 3,212 3,504 3,796 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 2,920 N/A 2,920 3,212 3,504 3,796 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,920 N/A 2,920 3,212 3,504 3,796 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 2,920 N/A 2,920 3,212 3,504 3,796 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 0,830 N/A 0,830 0,913 0,996 1,079 (H) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 0,830 N/A 0,830 0,913 0,996 1,079 (E)/(H) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,920 N/A 2,920 3,212 3,504 3,796 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,920 N/A 2,920 3,212 3,504 3,796 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 0,830 N/A 0,830 0,913 0,996 1,079 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,920 N/A 2,920 3,212 3,504 3,796 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,920 N/A 2,920 3,212 3,504 3,796 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 0,830 N/A 0,830 0,913 0,996 1,079 (H) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 0,830 N/A 0,830 0,913 0,996 1,079 (H) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 0,830 N/A 0,830 0,913 0,996 1,079 (H) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 2,920 N/A 2,920 3,212 3,504 3,796 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,920 N/A 2,920 3,212 3,504 3,796 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 0,830 N/A 0,830 0,913 0,996 1,079 (E) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,650 N/A 1,650 1,815 1,980 2,145 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,650 N/A 1,650 1,815 1,980 2,145 7307 19 90 Cast tube or pipe fittings of steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,360 N/A 2,360 2,596 2,832 3,068 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,360 N/A 2,360 2,596 2,832 3,068 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,360 N/A 2,360 2,596 2,832 3,068 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,360 N/A 2,360 2,596 2,832 3,068 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,180 N/A 2,180 2,398 2,616 2,834 (E) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,020 N/A 2,020 2,222 2,424 2,626 (E) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 0,840 N/A 0,840 0,924 1,008 1,092 (E) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,310 N/A 2,310 2,541 2,772 3,003 (E) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 2,920 N/A 2,920 3,212 3,504 3,796 (E) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 13 00 Screw hooks and screw rings, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 2,920 N/A 2,920 3,212 3,504 3,796 (E) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 1,370 N/A 1,370 1,507 1,644 1,781 (E) 7318 16 Nuts of iron or steel 1,370 N/A 1,370 1,507 1,644 1,781 (E) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 21 00 Spring washers and other lock washers, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,400 N/A 1,400 1,540 1,680 1,820 (E) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 1,200 N/A 1,200 1,320 1,440 1,560 (E) 7318 24 00 Cotters and cotter pins, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7318 29 00 Non-threaded articles, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 20 00 Articles of iron or steel wire, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 30 Ladders and steps, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 50 Reels for cables, piping and the like, of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 96 Sintered articles of iron or steel, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) 7326 90 98 Articles of iron or steel, n.e.s. 0,740 N/A 0,740 0,814 0,888 0,962 (E) Qatar Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,830 0,030 0,860 0,946 1,032 1,118 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,850 0,060 0,910 1,001 1,092 1,183 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,810 0,070 0,880 0,968 1,056 1,144 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,480 0,040 2,520 2,545 2,545 2,545 2814 10 00 Anhydrous ammonia 1,960 0,120 2,070 2,091 2,091 2,091 2814 20 00 Ammonia in aqueous solution 0,590 0,040 0,620 0,626 0,626 0,626 2834 21 00 Nitrate of potassium 2 0,060 2,050 2,071 2,071 2,071 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,420 0,030 0,460 0,465 0,465 0,465 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,700 0,030 0,740 0,747 0,747 0,747 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,280 0,090 1,370 1,384 1,384 1,384 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,250 0,090 1,340 1,353 1,353 1,353 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,070 0,640 0,646 0,646 0,646 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,270 0,080 1,350 1,364 1,364 1,364 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,510 0,060 1,570 1,586 1,586 1,586 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,320 0,090 2,420 2,444 2,444 2,444 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,090 2,070 2,091 2,091 2,091 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,980 0,090 2,070 2,091 2,091 2,091 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,870 0,060 3,930 3,969 3,969 3,969 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,950 0,080 2,030 2,050 2,050 2,050 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,440 0,070 1,520 1,535 1,535 1,535 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,090 1,560 1,576 1,576 1,576 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,070 0,810 0,818 0,818 0,818 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,090 1,060 1,071 1,071 1,071 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,070 0,720 0,727 0,727 0,727 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,050 0,510 0,515 0,515 0,515 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,110 1,440 1,454 1,454 1,454 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,520 0,090 0,620 0,626 0,626 0,626 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,060 1,380 1,394 1,394 1,394 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,050 0,720 0,727 0,727 0,727 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,030 N/A 2,030 2,233 2,436 2,639 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/(A 10,820 11,902 12,984 14,066 Russia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,330 0,040 1,360 1,496 1,632 1,768 (B) 2523 10 00 Grey clinker 1,330 0,030 1,360 1,496 1,632 1,768 (A) 2523 21 00 White Portland cement 1,310 0,130 1,440 1,584 1,728 1,872 2523 29 00 Grey Portland cement 1,330 0,050 1,380 1,518 1,656 1,794 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,700 0,030 2,730 2,757 2,757 2,757 2814 10 00 Anhydrous ammonia 2,160 0,100 2,260 2,283 2,283 2,283 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,170 0,040 2,220 2,242 2,242 2,242 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,020 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,020 0,790 0,798 0,798 0,798 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,400 0,070 1,470 1,485 1,485 1,485 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,370 0,070 1,440 1,454 1,454 1,454 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,050 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,390 0,060 1,450 1,465 1,465 1,465 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,050 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,530 0,070 2,600 2,626 2,626 2,626 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,070 2,220 2,242 2,242 2,242 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,070 2,220 2,242 2,242 2,242 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,210 0,050 4,260 4,303 4,303 4,303 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,060 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,570 0,060 1,630 1,646 1,646 1,646 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,600 0,070 1,670 1,687 1,687 1,687 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,060 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,070 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,050 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,040 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,030 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,450 0,080 1,530 1,545 1,545 1,545 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,080 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,050 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,040 0,760 0,768 0,768 0,768 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 2,160 N/A 2,160 2,376 2,592 2,808 (K) 7603 Aluminium powders and flakes 2,270 N/A 2,270 2,497 2,724 2,951 (K) 7604 10 10 Bars and rods 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7604 10 90 Profiles 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7604 21 00 Hollow profiles 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7604 29 10 Bars and rods 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7604 29 90 Profiles 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7605 Aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7608 Aluminium tubes and pipes 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7610 90 Other 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7610 90 90 Other 2,510 N/A 2,510 2,761 3,012 3,263 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,950 N/A 2,950 3,245 3,540 3,835 (K) 7616 99 10 Cast 2,270 N/A 2,270 2,497 2,724 2,951 (K) 7616 99 90 Other 2,950 N/A 2,950 3,245 3,540 3,835 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 1,570 0,040 1,610 1,771 1,932 2,093 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 3,040 N/A 3,040 3,344 3,648 3,952 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 2,010 N/A 2,010 2,211 2,412 2,613 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 3,090 N/A 3,090 3,399 3,708 4,017 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 3,430 N/A 3,430 3,773 4,116 4,459 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 3,430 N/A 3,430 3,773 4,116 4,459 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 3,430 N/A 3,430 3,773 4,116 4,459 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 3,430 N/A 3,430 3,773 4,116 4,459 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,180 N/A 3,180 3,498 3,816 4,134 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,550 N/A 3,550 3,905 4,260 4,615 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,550 N/A 3,550 3,905 4,260 4,615 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,180 N/A 3,180 3,498 3,816 4,134 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,550 N/A 3,550 3,905 4,260 4,615 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,180 N/A 3,180 3,498 3,816 4,134 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,550 N/A 3,550 3,905 4,260 4,615 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,710 N/A 3,710 4,081 4,452 4,823 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,710 N/A 3,710 4,081 4,452 4,823 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,710 N/A 3,710 4,081 4,452 4,823 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,710 N/A 3,710 4,081 4,452 4,823 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,710 N/A 3,710 4,081 4,452 4,823 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,710 N/A 3,710 4,081 4,452 4,823 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,550 N/A 3,550 3,905 4,260 4,615 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,550 N/A 3,550 3,905 4,260 4,615 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,710 N/A 3,710 4,081 4,452 4,823 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,710 N/A 3,710 4,081 4,452 4,823 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,180 N/A 3,180 3,498 3,816 4,134 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,180 N/A 3,180 3,498 3,816 4,134 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,180 N/A 3,180 3,498 3,816 4,134 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,180 N/A 3,180 3,498 3,816 4,134 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,180 N/A 3,180 3,498 3,816 4,134 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,180 N/A 3,180 3,498 3,816 4,134 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,180 N/A 3,180 3,498 3,816 4,134 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 02 Semi-finished products of tool steel 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,950 N/A 4,950 5,445 5,940 6,435 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,830 N/A 3,830 4,213 4,596 4,979 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,950 N/A 4,950 5,445 5,940 6,435 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,830 N/A 3,830 4,213 4,596 4,979 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,830 N/A 3,830 4,213 4,596 4,979 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,990 N/A 3,990 4,389 4,788 5,187 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,460 N/A 3,460 3,806 4,152 4,498 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,460 N/A 3,460 3,806 4,152 4,498 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 6,960 N/A 6,960 7,656 8,352 9,048 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,460 N/A 3,460 3,806 4,152 4,498 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,460 N/A 3,460 3,806 4,152 4,498 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,460 N/A 3,460 3,806 4,152 4,498 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,460 N/A 3,460 3,806 4,152 4,498 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,460 N/A 3,460 3,806 4,152 4,498 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,350 N/A 3,350 3,685 4,020 4,355 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,350 N/A 3,350 3,685 4,020 4,355 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,710 N/A 3,710 4,081 4,452 4,823 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,710 N/A 3,710 4,081 4,452 4,823 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 3,430 N/A 3,430 3,773 4,116 4,459 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,710 N/A 3,710 4,081 4,452 4,823 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,550 N/A 3,550 3,905 4,260 4,615 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 3,460 N/A 3,460 3,806 4,152 4,498 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,710 N/A 3,710 4,081 4,452 4,823 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,710 N/A 3,710 4,081 4,452 4,823 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,030 N/A 3,030 3,333 3,636 3,939 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,030 N/A 3,030 3,333 3,636 3,939 7307 19 90 Cast tube or pipe fittings of steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 3,360 N/A 3,360 3,696 4,032 4,368 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3,360 N/A 3,360 3,696 4,032 4,368 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3,360 N/A 3,360 3,696 4,032 4,368 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3,360 N/A 3,360 3,696 4,032 4,368 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 3,490 N/A 3,490 3,839 4,188 4,537 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,180 N/A 3,180 3,498 3,816 4,134 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,180 N/A 3,180 3,498 3,816 4,134 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 16 Nuts of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7318 29 00 Non-threaded articles, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 30 Ladders and steps, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7326 90 98 Articles of iron or steel, n.e.s. 3,590 N/A 3,590 3,949 4,308 4,667 (C) Rwanda Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,030 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,870 0,050 0,910 1,001 1,092 1,183 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,830 0,050 0,880 0,968 1,056 1,144 (A) 2523 30 00 Aluminous cement - - - - - - Saudi Arabia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,450 0,050 2,500 2,525 2,525 2,525 2814 10 00 Anhydrous ammonia 1,960 0,150 2,100 2,121 2,121 2,121 2814 20 00 Ammonia in aqueous solution 0,590 0,040 0,630 0,636 0,636 0,636 2834 21 00 Nitrate of potassium 1,980 0,070 2,060 2,081 2,081 2,081 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,040 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,040 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,350 0,120 1,470 1,485 1,485 1,485 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,320 0,120 1,440 1,454 1,454 1,454 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,090 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,100 1,380 1,394 1,394 1,394 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,500 0,080 1,580 1,596 1,596 1,596 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,310 0,120 2,430 2,454 2,454 2,454 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,110 2,100 2,121 2,121 2,121 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,110 2,100 2,121 2,121 2,121 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,820 0,080 3,900 3,939 3,939 3,939 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,100 2,040 2,060 2,060 2,060 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,460 0,090 1,550 1,566 1,566 1,566 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,510 0,110 1,620 1,636 1,636 1,636 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,090 0,830 0,838 0,838 0,838 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,110 1,090 1,101 1,101 1,101 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,080 0,750 0,758 0,758 0,758 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,070 0,530 0,535 0,535 0,535 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,050 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,140 1,480 1,495 1,495 1,495 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,110 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,080 1,390 1,404 1,404 1,404 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,060 0,730 0,737 0,737 0,737 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 13,450 N/A 13,450 14,795 16,140 17,485 Senegal Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - (A) 2523 10 00 White clinker - - - - - - (B) 2523 10 00 Grey clinker 1,240 0,050 1,300 1,430 1,560 1,690 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,230 0,090 1,320 1,452 1,584 1,716 2523 90 00 White hydraulic cements - - - - - - (B) 2523 90 00 Grey hydraulic cements - - - - - - (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,670 0,060 1,720 1,737 1,737 1,737 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,640 0,050 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 1,500 0,080 1,580 1,596 1,596 1,596 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,040 0,510 0,515 0,515 0,515 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,780 0,040 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,140 1,550 1,566 1,566 1,566 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,130 1,520 1,535 1,535 1,535 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,100 0,720 0,727 0,727 0,727 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,080 0,120 1,190 1,202 1,202 1,202 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,140 0,090 1,230 1,242 1,242 1,242 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,130 1,890 1,909 1,909 1,909 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,510 0,120 1,630 1,646 1,646 1,646 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,510 0,120 1,630 1,646 1,646 1,646 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,600 0,090 2,690 2,717 2,717 2,717 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,120 1,590 1,606 1,606 1,606 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,230 0,110 1,340 1,353 1,353 1,353 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,360 0,130 1,480 1,495 1,495 1,495 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,640 0,100 0,750 0,758 0,758 0,758 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,760 0,130 0,890 0,899 0,899 0,899 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,100 0,620 0,626 0,626 0,626 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,080 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,060 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,040 0,160 1,200 1,212 1,212 1,212 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,120 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,010 0,090 1,100 1,111 1,111 1,111 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,520 0,070 0,590 0,596 0,596 0,596 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Serbia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,330 0,060 1,380 1,518 1,656 1,794 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,310 0,100 1,410 1,551 1,692 1,833 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,240 0,100 1,350 1,485 1,620 1,755 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,700 0,030 2,730 2,757 2,757 2,757 2814 10 00 Anhydrous ammonia 2,160 0,100 2,260 2,283 2,283 2,283 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,180 0,050 2,220 2,242 2,242 2,242 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,020 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,020 0,790 0,798 0,798 0,798 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,390 0,080 1,460 1,475 1,475 1,475 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,360 0,070 1,430 1,444 1,444 1,444 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,060 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,390 0,060 1,450 1,465 1,465 1,465 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,050 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,530 0,070 2,600 2,626 2,626 2,626 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,070 2,220 2,242 2,242 2,242 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,070 2,220 2,242 2,242 2,242 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,220 0,050 4,270 4,313 4,313 4,313 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,060 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,570 0,060 1,630 1,646 1,646 1,646 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,600 0,070 1,660 1,677 1,677 1,677 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,060 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,070 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,050 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,040 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,030 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,450 0,080 1,530 1,545 1,545 1,545 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,080 0,650 0,657 0,657 0,657 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,050 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,040 0,760 0,768 0,768 0,768 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,513 N/A 1,513 1,664 1,816 1,967 (L) 7604 10 10 Bars and rods 2,238 N/A 2,238 2,462 2,686 2,909 (L) 7604 10 90 Profiles 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7604 21 00 Hollow profiles 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7604 29 10 Bars and rods 2,238 N/A 2,238 2,462 2,686 2,909 (L) 7604 29 90 Profiles 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7605 Aluminium wire 2,238 N/A 2,238 2,462 2,686 2,909 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 3,688 N/A 3,688 4,057 4,426 4,794 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 3,688 N/A 3,688 4,057 4,426 4,794 (L) 7608 Aluminium tubes and pipes 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7610 90 Other 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7610 90 90 Other 2,270 N/A 2,270 2,496 2,723 2,950 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,688 N/A 3,688 4,057 4,426 4,794 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,544 N/A 1,544 1,698 1,853 2,007 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 3,688 N/A 3,688 4,057 4,426 4,794 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,238 N/A 2,238 2,462 2,686 2,909 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 3,688 N/A 3,688 4,057 4,426 4,794 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 3,688 N/A 3,688 4,057 4,426 4,794 (L) 7616 99 10 Cast 1,513 N/A 1,513 1,664 1,816 1,967 (L) 7616 99 90 Other 3,688 N/A 3,688 4,057 4,426 4,794 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,120 0,110 0,220 0,242 0,264 0,286 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,160 N/A 2,160 2,376 2,592 2,808 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,641 N/A 2,641 2,905 3,169 3,433 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,580 N/A 2,580 2,838 3,096 3,354 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 2,590 N/A 2,590 2,849 3,108 3,367 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 2,590 N/A 2,590 2,849 3,108 3,367 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 2,580 N/A 2,580 2,838 3,096 3,354 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 2,590 N/A 2,590 2,849 3,108 3,367 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 2,580 N/A 2,580 2,838 3,096 3,354 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 2,590 N/A 2,590 2,849 3,108 3,367 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,590 N/A 2,590 2,849 3,108 3,367 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 2,590 N/A 2,590 2,849 3,108 3,367 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 2,590 N/A 2,590 2,849 3,108 3,367 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 2,590 N/A 2,590 2,849 3,108 3,367 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 2,590 N/A 2,590 2,849 3,108 3,367 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 2,590 N/A 2,590 2,849 3,108 3,367 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 2,590 N/A 2,590 2,849 3,108 3,367 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 2,590 N/A 2,590 2,849 3,108 3,367 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 2,590 N/A 2,590 2,849 3,108 3,367 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 2,580 N/A 2,580 2,838 3,096 3,354 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 2,590 N/A 2,590 2,849 3,108 3,367 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 2,590 N/A 2,590 2,849 3,108 3,367 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,550 N/A 2,550 2,805 3,060 3,315 (F) 7224 90 02 Semi-finished products of tool steel 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 2,550 N/A 2,550 2,805 3,060 3,315 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 2,550 N/A 2,550 2,805 3,060 3,315 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 3,390 N/A 3,390 3,729 4,068 4,407 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 3,390 N/A 3,390 3,729 4,068 4,407 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 2,560 N/A 2,560 2,816 3,072 3,328 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 2,560 N/A 2,560 2,816 3,072 3,328 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,550 N/A 2,550 2,805 3,060 3,315 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,560 N/A 2,560 2,816 3,072 3,328 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,550 N/A 2,550 2,805 3,060 3,315 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,560 N/A 2,560 2,816 3,072 3,328 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 2,560 N/A 2,560 2,816 3,072 3,328 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 2,560 N/A 2,560 2,816 3,072 3,328 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,460 N/A 2,460 2,706 2,952 3,198 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,230 N/A 2,230 2,453 2,676 2,899 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 2,590 N/A 2,590 2,849 3,108 3,367 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 2,590 N/A 2,590 2,849 3,108 3,367 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 2,590 N/A 2,590 2,849 3,108 3,367 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,590 N/A 2,590 2,849 3,108 3,367 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 2,590 N/A 2,590 2,849 3,108 3,367 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,310 N/A 2,310 2,541 2,772 3,003 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,310 N/A 2,310 2,541 2,772 3,003 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,590 N/A 2,590 2,849 3,108 3,367 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,590 N/A 2,590 2,849 3,108 3,367 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,410 N/A 2,410 2,651 2,892 3,133 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,590 N/A 2,590 2,849 3,108 3,367 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,590 N/A 2,590 2,849 3,108 3,367 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,320 N/A 2,320 2,552 2,784 3,016 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,320 N/A 2,320 2,552 2,784 3,016 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,320 N/A 2,320 2,552 2,784 3,016 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 2,590 N/A 2,590 2,849 3,108 3,367 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,590 N/A 2,590 2,849 3,108 3,367 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,220 N/A 2,220 2,442 2,664 2,886 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,220 N/A 2,220 2,442 2,664 2,886 7307 19 90 Cast tube or pipe fittings of steel 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,480 N/A 2,480 2,728 2,976 3,224 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,480 N/A 2,480 2,728 2,976 3,224 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,480 N/A 2,480 2,728 2,976 3,224 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,480 N/A 2,480 2,728 2,976 3,224 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,480 N/A 2,480 2,728 2,976 3,224 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 2,590 N/A 2,590 2,849 3,108 3,367 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 2,590 N/A 2,590 2,849 3,108 3,367 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7318 16 Nuts of iron or steel 2,440 N/A 2,440 2,684 2,928 3,172 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,450 N/A 2,450 2,695 2,940 3,185 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 30 Ladders and steps, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,400 N/A 2,400 2,640 2,880 3,120 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,410 N/A 2,410 2,651 2,892 3,133 (C) Sierra Leone Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Singapore Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker - - - - - - 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,030 0,060 1,090 1,199 1,308 1,417 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,990 0,060 1,050 1,155 1,260 1,365 (A) 2523 30 00 Aluminous cement - - - - - - Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,780 N/A 1,780 1,958 2,136 2,314 (L) 7604 10 10 Bars and rods 2,010 N/A 2,010 2,211 2,412 2,613 (L) 7604 10 90 Profiles 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7604 21 00 Hollow profiles 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7604 29 10 Bars and rods 2,010 N/A 2,010 2,211 2,412 2,613 (L) 7604 29 90 Profiles 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7605 Aluminium wire 2,010 N/A 2,010 2,211 2,412 2,613 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7608 Aluminium tubes and pipes 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7610 90 Other 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7610 90 90 Other 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,010 N/A 2,010 2,211 2,412 2,613 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,460 N/A 2,460 2,706 2,952 3,198 (L) 7616 99 10 Cast 1,780 N/A 1,780 1,958 2,136 2,314 (L) 7616 99 90 Other 2,460 N/A 2,460 2,706 2,952 3,198 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 South Africa Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,020 0,080 2,100 2,121 2,121 2,121 2814 10 00 Anhydrous ammonia 3,390 0,250 3,640 3,676 3,676 3,676 2814 20 00 Ammonia in aqueous solution 1,020 0,070 1,090 1,101 1,101 1,101 2834 21 00 Nitrate of potassium 1,950 0,120 2,070 2,091 2,091 2,091 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,720 0,060 0,780 0,788 0,788 0,788 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,190 0,060 1,260 1,273 1,273 1,273 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,160 0,200 2,360 2,384 2,384 2,384 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2,120 0,190 2,310 2,333 2,333 2,333 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,150 1,120 1,131 1,131 1,131 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,500 0,170 1,670 1,687 1,687 1,687 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,490 0,130 1,620 1,636 1,636 1,636 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,300 0,190 2,490 2,515 2,515 2,515 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,970 0,180 2,150 2,172 2,172 2,172 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,970 0,180 2,150 2,172 2,172 2,172 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,140 0,130 3,270 3,303 3,303 3,303 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,930 0,170 2,100 2,121 2,121 2,121 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,710 0,150 1,860 1,879 1,879 1,879 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,950 0,180 2,140 2,161 2,161 2,161 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,910 0,150 1,060 1,071 1,071 1,071 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,020 0,180 1,200 1,212 1,212 1,212 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,700 0,140 0,840 0,848 0,848 0,848 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,790 0,110 0,900 0,909 0,909 0,909 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,090 0,590 0,596 0,596 0,596 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,380 0,220 1,600 1,616 1,616 1,616 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,900 0,180 1,070 1,081 1,081 1,081 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,340 0,140 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,690 0,100 0,790 0,798 0,798 0,798 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 2,358 N/A 2,358 2,594 2,830 3,066 (K) 7603 Aluminium powders and flakes 1,990 N/A 1,990 2,189 2,388 2,587 (K) 7604 10 10 Bars and rods 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7604 10 90 Profiles 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7604 21 00 Hollow profiles 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7604 29 10 Bars and rods 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7604 29 90 Profiles 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7605 Aluminium wire 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7608 Aluminium tubes and pipes 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 90 Other 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7610 90 90 Other 2,230 N/A 2,230 2,453 2,676 2,899 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,210 N/A 2,210 2,431 2,652 2,873 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,670 N/A 2,670 2,937 3,204 3,471 (K) 7616 99 10 Cast 1,990 N/A 1,990 2,189 2,388 2,587 (K) 7616 99 90 Other 2,670 N/A 2,670 2,937 3,204 3,471 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 25,940 N/A 25,940 28,534 31,128 33,722 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) - - - - - - 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 3,470 N/A 3,470 3,817 4,164 4,511 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon 2,870 N/A 2,870 3,157 3,444 3,731 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 0,760 N/A 0,760 0,836 0,912 0,988 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 3,890 N/A 3,890 4,279 4,668 5,057 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 4,140 N/A 4,140 4,554 4,968 5,382 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 4,140 N/A 4,140 4,554 4,968 5,382 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 4,140 N/A 4,140 4,554 4,968 5,382 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 4,140 N/A 4,140 4,554 4,968 5,382 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,620 N/A 3,620 3,982 4,344 4,706 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,810 N/A 3,810 4,191 4,572 4,953 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,810 N/A 3,810 4,191 4,572 4,953 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,620 N/A 3,620 3,982 4,344 4,706 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,810 N/A 3,810 4,191 4,572 4,953 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,620 N/A 3,620 3,982 4,344 4,706 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,810 N/A 3,810 4,191 4,572 4,953 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,890 N/A 3,890 4,279 4,668 5,057 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,890 N/A 3,890 4,279 4,668 5,057 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,890 N/A 3,890 4,279 4,668 5,057 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,890 N/A 3,890 4,279 4,668 5,057 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,890 N/A 3,890 4,279 4,668 5,057 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,890 N/A 3,890 4,279 4,668 5,057 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,810 N/A 3,810 4,191 4,572 4,953 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,810 N/A 3,810 4,191 4,572 4,953 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,890 N/A 3,890 4,279 4,668 5,057 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,890 N/A 3,890 4,279 4,668 5,057 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,620 N/A 3,620 3,982 4,344 4,706 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,620 N/A 3,620 3,982 4,344 4,706 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,620 N/A 3,620 3,982 4,344 4,706 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,620 N/A 3,620 3,982 4,344 4,706 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,620 N/A 3,620 3,982 4,344 4,706 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,620 N/A 3,620 3,982 4,344 4,706 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,620 N/A 3,620 3,982 4,344 4,706 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7224 90 02 Semi-finished products of tool steel 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 5,340 N/A 5,340 5,874 6,408 6,942 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 4,080 N/A 4,080 4,488 4,896 5,304 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 5,340 N/A 5,340 5,874 6,408 6,942 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 4,080 N/A 4,080 4,488 4,896 5,304 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,890 N/A 3,890 4,279 4,668 5,057 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,890 N/A 3,890 4,279 4,668 5,057 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,890 N/A 3,890 4,279 4,668 5,057 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 3,480 N/A 3,480 3,828 4,176 4,524 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,620 N/A 3,620 3,982 4,344 4,706 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,620 N/A 3,620 3,982 4,344 4,706 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,620 N/A 3,620 3,982 4,344 4,706 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,620 N/A 3,620 3,982 4,344 4,706 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,620 N/A 3,620 3,982 4,344 4,706 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,850 N/A 3,850 4,235 4,620 5,005 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,850 N/A 3,850 4,235 4,620 5,005 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,890 N/A 3,890 4,279 4,668 5,057 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,890 N/A 3,890 4,279 4,668 5,057 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 4,140 N/A 4,140 4,554 4,968 5,382 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,890 N/A 3,890 4,279 4,668 5,057 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,810 N/A 3,810 4,191 4,572 4,953 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 4,080 N/A 4,080 4,488 4,896 5,304 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 4,160 N/A 4,160 4,576 4,992 5,408 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,890 N/A 3,890 4,279 4,668 5,057 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,890 N/A 3,890 4,279 4,668 5,057 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,480 N/A 3,480 3,828 4,176 4,524 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,480 N/A 3,480 3,828 4,176 4,524 7307 19 90 Cast tube or pipe fittings of steel 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 3,870 N/A 3,870 4,257 4,644 5,031 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3,870 N/A 3,870 4,257 4,644 5,031 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3,870 N/A 3,870 4,257 4,644 5,031 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3,870 N/A 3,870 4,257 4,644 5,031 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 4,220 N/A 4,220 4,642 5,064 5,486 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,620 N/A 3,620 3,982 4,344 4,706 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,620 N/A 3,620 3,982 4,344 4,706 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 16 Nuts of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7318 29 00 Non-threaded articles, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7326 90 30 Ladders and steps, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 4,020 N/A 4,020 4,422 4,824 5,226 (C) 7326 90 98 Articles of iron or steel, n.e.s. 4,220 N/A 4,220 4,642 5,064 5,486 (C) South Korea Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,190 0,040 1,230 1,353 1,476 1,599 2523 10 00 Grey clinker 0,880 0,030 0,920 1,012 1,104 1,196 (A) 2523 21 00 White Portland cement 1,230 0,130 1,360 1,496 1,632 1,768 2523 29 00 Grey Portland cement 0,890 0,060 0,940 1,034 1,128 1,222 2523 90 00 White hydraulic cements 1,260 0,160 1,420 1,562 1,704 1,846 2523 90 00 Grey hydraulic cements 0,840 0,060 0,910 1,001 1,092 1,183 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,130 0,060 2,190 2,212 2,212 2,212 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,620 0,060 0,670 0,677 0,677 0,677 2834 21 00 Nitrate of potassium 1,790 0,080 1,880 1,899 1,899 1,899 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,040 0,510 0,515 0,515 0,515 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,040 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,140 1,540 1,555 1,555 1,555 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,130 1,510 1,525 1,525 1,525 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,090 0,700 0,707 0,707 0,707 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,210 0,100 1,310 1,323 1,323 1,323 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,360 0,080 1,440 1,454 1,454 1,454 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,090 0,130 2,220 2,242 2,242 2,242 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,800 0,110 1,920 1,939 1,939 1,939 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,800 0,110 1,920 1,939 1,939 1,939 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,320 0,090 3,420 3,454 3,454 3,454 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,760 0,110 1,860 1,879 1,879 1,879 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,380 0,100 1,480 1,495 1,495 1,495 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,470 0,120 1,590 1,606 1,606 1,606 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,710 0,090 0,800 0,808 0,808 0,808 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,900 0,100 1 1,010 1,010 1,010 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,080 0,690 0,697 0,697 0,697 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,070 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,050 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,230 0,130 1,360 1,374 1,374 1,374 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,110 0,670 0,677 0,677 0,677 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,190 0,080 1,280 1,293 1,293 1,293 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,610 0,060 0,670 0,677 0,677 0,677 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,260 N/A 1,260 1,386 1,512 1,638 (L) 7604 10 10 Bars and rods 1,490 N/A 1,490 1,639 1,788 1,937 (L) 7604 10 90 Profiles 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7604 21 00 Hollow profiles 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7604 29 10 Bars and rods 1,490 N/A 1,490 1,639 1,788 1,937 (L) 7604 29 90 Profiles 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7605 Aluminium wire 1,490 N/A 1,490 1,639 1,788 1,937 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7608 Aluminium tubes and pipes 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7610 90 Other 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7610 90 90 Other 1,500 N/A 1,500 1,650 1,800 1,950 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,490 N/A 1,490 1,639 1,788 1,937 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,950 N/A 1,950 2,145 2,340 2,535 (L) 7616 99 10 Cast 1,260 N/A 1,260 1,386 1,512 1,638 (L) 7616 99 90 Other 1,950 N/A 1,950 2,145 2,340 2,535 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 14,030 N/A 14,030 15,433 16,836 18,239 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,100 0,040 0,130 0,143 0,156 0,169 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,540 N/A 1,540 1,694 1,848 2,002 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon 5,590 N/A 5,590 6,149 6,708 7,267 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,580 N/A 1,580 1,738 1,896 2,054 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,640 N/A 1,640 1,804 1,968 2,132 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,118 N/A 2,118 2,330 2,542 2,754 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,760 N/A 3,760 4,136 4,512 4,888 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,630 N/A 3,630 3,993 4,356 4,719 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,630 N/A 3,630 3,993 4,356 4,719 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,760 N/A 3,760 4,136 4,512 4,888 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,630 N/A 3,630 3,993 4,356 4,719 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,760 N/A 3,760 4,136 4,512 4,888 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,630 N/A 3,630 3,993 4,356 4,719 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,650 N/A 3,650 4,015 4,380 4,745 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,650 N/A 3,650 4,015 4,380 4,745 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,650 N/A 3,650 4,015 4,380 4,745 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,650 N/A 3,650 4,015 4,380 4,745 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,650 N/A 3,650 4,015 4,380 4,745 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,650 N/A 3,650 4,015 4,380 4,745 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,630 N/A 3,630 3,993 4,356 4,719 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,630 N/A 3,630 3,993 4,356 4,719 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,650 N/A 3,650 4,015 4,380 4,745 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,650 N/A 3,650 4,015 4,380 4,745 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,650 N/A 3,650 4,015 4,380 4,745 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,650 N/A 3,650 4,015 4,380 4,745 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,650 N/A 3,650 4,015 4,380 4,745 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,650 N/A 3,650 4,015 4,380 4,745 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,760 N/A 3,760 4,136 4,512 4,888 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,650 N/A 3,650 4,015 4,380 4,745 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,650 N/A 3,650 4,015 4,380 4,745 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 4,150 N/A 4,150 4,565 4,980 5,395 (F) 7224 90 02 Semi-finished products of tool steel 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 4,150 N/A 4,150 4,565 4,980 5,395 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 4,150 N/A 4,150 4,565 4,980 5,395 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 5,320 N/A 5,320 5,852 6,384 6,916 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 5,320 N/A 5,320 5,852 6,384 6,916 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 4,030 N/A 4,030 4,433 4,836 5,239 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 4,030 N/A 4,030 4,433 4,836 5,239 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 4,050 N/A 4,050 4,455 4,860 5,265 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,150 N/A 4,150 4,565 4,980 5,395 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,050 N/A 4,050 4,455 4,860 5,265 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,150 N/A 4,150 4,565 4,980 5,395 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,050 N/A 4,050 4,455 4,860 5,265 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 4,050 N/A 4,050 4,455 4,860 5,265 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 4,050 N/A 4,050 4,455 4,860 5,265 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,144 N/A 2,144 2,358 2,573 2,787 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,674 N/A 3,674 4,041 4,409 4,776 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,154 N/A 2,154 2,369 2,585 2,800 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 4,084 N/A 4,084 4,492 4,901 5,309 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 4,084 N/A 4,084 4,492 4,901 5,309 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 4,084 N/A 4,084 4,492 4,901 5,309 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 4,084 N/A 4,084 4,492 4,901 5,309 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 4,084 N/A 4,084 4,492 4,901 5,309 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,144 N/A 2,144 2,358 2,573 2,787 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,144 N/A 2,144 2,358 2,573 2,787 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,154 N/A 2,154 2,369 2,585 2,800 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,114 N/A 4,114 4,525 4,937 5,348 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,114 N/A 4,114 4,525 4,937 5,348 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,144 N/A 2,144 2,358 2,573 2,787 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,114 N/A 4,114 4,525 4,937 5,348 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,094 N/A 4,094 4,503 4,913 5,322 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,184 N/A 2,184 2,402 2,621 2,839 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,164 N/A 2,164 2,380 2,597 2,813 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,184 N/A 2,184 2,402 2,621 2,839 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 4,114 N/A 4,114 4,525 4,937 5,348 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,114 N/A 4,114 4,525 4,937 5,348 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,194 N/A 2,194 2,413 2,633 2,852 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,194 N/A 2,194 2,413 2,633 2,852 7307 19 90 Cast tube or pipe fittings of steel 2,274 N/A 2,274 2,501 2,729 2,956 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 3,774 N/A 3,774 4,151 4,529 4,906 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3,774 N/A 3,774 4,151 4,529 4,906 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3,774 N/A 3,774 4,151 4,529 4,906 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3,774 N/A 3,774 4,151 4,529 4,906 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,134 N/A 2,134 2,347 2,561 2,774 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,134 N/A 2,134 2,347 2,561 2,774 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,134 N/A 2,134 2,347 2,561 2,774 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,134 N/A 2,134 2,347 2,561 2,774 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,864 N/A 3,864 4,250 4,637 5,023 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 4,124 N/A 4,124 4,536 4,949 5,361 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,164 N/A 2,164 2,380 2,597 2,813 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 4,104 N/A 4,104 4,514 4,925 5,335 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 4,074 N/A 4,074 4,481 4,889 5,296 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 4,074 N/A 4,074 4,481 4,889 5,296 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 3,474 N/A 3,474 3,821 4,169 4,516 (C) 7318 16 Nuts of iron or steel 4,104 N/A 4,104 4,514 4,925 5,335 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,484 N/A 2,484 2,732 2,981 3,229 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,344 N/A 2,344 2,578 2,813 3,047 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,274 N/A 2,274 2,501 2,729 2,956 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,274 N/A 2,274 2,501 2,729 2,956 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7326 90 30 Ladders and steps, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,124 N/A 2,124 2,336 2,549 2,761 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,274 N/A 2,274 2,501 2,729 2,956 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,274 N/A 2,274 2,501 2,729 2,956 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,274 N/A 2,274 2,501 2,729 2,956 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,144 N/A 2,144 2,358 2,573 2,787 (C) Sri Lanka Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,870 0,040 0,900 0,990 1,080 1,170 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1 0,060 1,060 1,166 1,272 1,378 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,950 0,070 1,020 1,122 1,224 1,326 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,040 0,070 2,110 2,131 2,131 2,131 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,700 0,060 0,770 0,778 0,778 0,778 2834 21 00 Nitrate of potassium 1,780 0,100 1,880 1,899 1,899 1,899 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,520 0,050 0,570 0,576 0,576 0,576 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,860 0,050 0,920 0,929 0,929 0,929 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,570 0,150 1,720 1,737 1,737 1,737 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,540 0,150 1,690 1,707 1,707 1,707 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,100 0,790 0,798 0,798 0,798 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,250 0,120 1,370 1,384 1,384 1,384 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,360 0,090 1,450 1,465 1,465 1,465 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,080 0,140 2,230 2,252 2,252 2,252 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,800 0,130 1,920 1,939 1,939 1,939 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,800 0,130 1,920 1,939 1,939 1,939 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,180 0,100 3,290 3,323 3,323 3,323 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,750 0,120 1,870 1,889 1,889 1,889 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,430 0,120 1,550 1,566 1,566 1,566 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,560 0,140 1,690 1,707 1,707 1,707 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,100 0,840 0,848 0,848 0,848 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,900 0,120 1,020 1,030 1,030 1,030 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,090 0,700 0,707 0,707 0,707 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,080 0,630 0,636 0,636 0,636 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,350 0,060 0,410 0,414 0,414 0,414 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,230 0,150 1,380 1,394 1,394 1,394 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,630 0,120 0,750 0,758 0,758 0,758 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,190 0,100 1,290 1,303 1,303 1,303 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,610 0,060 0,680 0,687 0,687 0,687 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,050 N/A 1,050 1,155 1,260 1,365 (L) 7604 10 10 Bars and rods 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7604 10 90 Profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 21 00 Hollow profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 29 10 Bars and rods 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7604 29 90 Profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7605 Aluminium wire 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7608 Aluminium tubes and pipes 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 Other 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 90 Other 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7616 99 10 Cast 1,050 N/A 1,050 1,155 1,260 1,365 (L) 7616 99 90 Other 1,730 N/A 1,730 1,903 2,076 2,249 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Sudan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,020 0,870 0,957 1,044 1,131 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,860 0,040 0,900 0,990 1,080 1,170 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,820 0,040 0,870 0,957 1,044 1,131 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,920 0,040 1,960 1,980 1,980 1,980 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,610 0,030 0,640 0,646 0,646 0,646 2834 21 00 Nitrate of potassium 1,650 0,050 1,700 1,717 1,717 1,717 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,030 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,030 0,790 0,798 0,798 0,798 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,400 0,080 1,480 1,495 1,495 1,495 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,360 0,080 1,440 1,454 1,454 1,454 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,050 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,140 0,060 1,200 1,212 1,212 1,212 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,260 0,050 1,300 1,313 1,313 1,313 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,930 0,070 2,010 2,030 2,030 2,030 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,670 0,070 1,740 1,757 1,757 1,757 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,670 0,070 1,740 1,757 1,757 1,757 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3 0,060 3,060 3,091 3,091 3,091 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,620 0,060 1,680 1,697 1,697 1,697 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,300 0,060 1,360 1,374 1,374 1,374 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,410 0,070 1,480 1,495 1,495 1,495 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,670 0,050 0,730 0,737 0,737 0,737 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,060 0,900 0,909 0,909 0,909 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,570 0,050 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,040 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,030 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,140 0,080 1,220 1,232 1,232 1,232 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,080 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,050 1,150 1,162 1,162 1,162 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,570 0,030 0,600 0,606 0,606 0,606 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Suriname Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker - - - - - - 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,180 0,060 1,240 1,364 1,488 1,612 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,120 0,060 1,180 1,298 1,416 1,534 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,040 1,840 1,858 1,858 1,858 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,680 0,040 0,720 0,727 0,727 0,727 2834 21 00 Nitrate of potassium 1,580 0,060 1,630 1,646 1,646 1,646 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,430 0,030 0,450 0,455 0,455 0,455 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,710 0,030 0,730 0,737 0,737 0,737 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,280 0,080 1,360 1,374 1,374 1,374 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,260 0,080 1,340 1,353 1,353 1,353 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,040 0,620 0,626 0,626 0,626 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,080 0,050 1,130 1,141 1,141 1,141 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,180 0,040 1,220 1,232 1,232 1,232 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,810 0,060 1,880 1,899 1,899 1,899 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,520 0,050 1,570 1,586 1,586 1,586 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,520 0,050 1,570 1,586 1,586 1,586 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,800 0,070 2,870 2,899 2,899 2,899 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,520 0,050 1,570 1,586 1,586 1,586 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,230 0,050 1,280 1,293 1,293 1,293 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,300 0,060 1,370 1,384 1,384 1,384 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,630 0,030 0,660 0,667 0,667 0,667 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,750 0,030 0,780 0,788 0,788 0,788 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,020 0,520 0,525 0,525 0,525 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,030 0,530 0,535 0,535 0,535 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,020 0,320 0,323 0,323 0,323 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,030 0,040 1,070 1,081 1,081 1,081 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,520 0,030 0,550 0,556 0,556 0,556 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,030 0,040 1,070 1,081 1,081 1,081 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,520 0,020 0,530 0,535 0,535 0,535 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Syria Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,280 0,050 1,330 1,463 1,596 1,729 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,280 0,100 1,380 1,518 1,656 1,794 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,220 0,100 1,320 1,452 1,584 1,716 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,460 0,060 2,520 2,545 2,545 2,545 2814 10 00 Anhydrous ammonia 1,970 0,180 2,140 2,161 2,161 2,161 2814 20 00 Ammonia in aqueous solution 0,590 0,050 0,640 0,646 0,646 0,646 2834 21 00 Nitrate of potassium 1,990 0,080 2,080 2,101 2,101 2,101 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,050 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,050 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,340 0,140 1,480 1,495 1,495 1,495 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,310 0,140 1,450 1,465 1,465 1,465 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,110 0,690 0,697 0,697 0,697 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,280 0,120 1,400 1,414 1,414 1,414 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,510 0,090 1,600 1,616 1,616 1,616 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,320 0,140 2,460 2,485 2,485 2,485 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,130 2,120 2,141 2,141 2,141 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,990 0,130 2,120 2,141 2,141 2,141 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,840 0,090 3,930 3,969 3,969 3,969 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,940 0,120 2,070 2,091 2,091 2,091 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,460 0,110 1,570 1,586 1,586 1,586 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,500 0,130 1,630 1,646 1,646 1,646 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,740 0,110 0,850 0,859 0,859 0,859 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,130 1,110 1,121 1,121 1,121 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,100 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,080 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,060 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,160 1,510 1,525 1,525 1,525 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,120 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,310 0,100 1,410 1,424 1,424 1,424 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,070 0,740 0,747 0,747 0,747 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,490 N/A 0,490 0,539 0,588 0,637 (L) 7604 10 10 Bars and rods 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 10 90 Profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 21 00 Hollow profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 29 10 Bars and rods 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 90 Profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7605 Aluminium wire 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7608 Aluminium tubes and pipes 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 Other 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 90 Other 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,170 N/A 1,170 1,287 1,404 1,521 (L) 7616 99 10 Cast 0,490 N/A 0,490 0,539 0,588 0,637 (L) 7616 99 90 Other 1,170 N/A 1,170 1,287 1,404 1,521 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Taiwan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,830 0,040 0,860 0,946 1,032 1,118 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,830 0,070 0,890 0,979 1,068 1,157 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,110 0,050 2,160 2,182 2,182 2,182 2814 10 00 Anhydrous ammonia 2,050 0,150 2,200 2,222 2,222 2,222 2814 20 00 Ammonia in aqueous solution 0,620 0,040 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 1,760 0,070 1,830 1,848 1,848 1,848 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,420 0,040 0,460 0,465 0,465 0,465 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,700 0,040 0,740 0,747 0,747 0,747 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,270 0,120 1,390 1,404 1,404 1,404 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,240 0,120 1,360 1,374 1,374 1,374 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,090 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,170 0,100 1,270 1,283 1,283 1,283 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,330 0,080 1,410 1,424 1,424 1,424 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,050 0,120 2,170 2,192 2,192 2,192 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,740 0,110 1,850 1,869 1,869 1,869 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,740 0,110 1,850 1,869 1,869 1,869 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,300 0,080 3,370 3,404 3,404 3,404 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,720 0,100 1,820 1,838 1,838 1,838 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,320 0,090 1,410 1,424 1,424 1,424 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,370 0,110 1,480 1,495 1,495 1,495 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,680 0,090 0,770 0,778 0,778 0,778 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,860 0,110 0,970 0,980 0,980 0,980 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,080 0,670 0,677 0,677 0,677 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,070 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,050 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,180 0,130 1,320 1,333 1,333 1,333 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,530 0,100 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,160 0,080 1,250 1,263 1,263 1,263 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,600 0,060 0,650 0,657 0,657 0,657 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7604 10 10 Bars and rods 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7604 10 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 21 00 Hollow profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7604 29 10 Bars and rods 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7604 29 90 Profiles 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7605 Aluminium wire 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7608 Aluminium tubes and pipes 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7610 90 90 Other 0,710 N/A 0,710 0,781 0,852 0,923 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,690 N/A 0,690 0,759 0,828 0,897 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,150 N/A 1,150 1,265 1,380 1,495 (L) 7616 99 10 Cast 0,470 N/A 0,470 0,517 0,564 0,611 (L) 7616 99 90 Other 1,150 N/A 1,150 1,265 1,380 1,495 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,180 0,040 0,220 0,242 0,264 0,286 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,860 N/A 1,860 2,046 2,232 2,418 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - - - - 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - - - - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,870 N/A 1,870 2,057 2,244 2,431 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,940 N/A 1,940 2,134 2,328 2,522 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,310 N/A 2,310 2,541 2,771 3,002 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,310 N/A 2,310 2,541 2,771 3,002 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,310 N/A 2,310 2,541 2,771 3,002 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,310 N/A 2,310 2,541 2,771 3,002 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,474 N/A 2,474 2,721 2,968 3,216 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,298 N/A 2,298 2,528 2,757 2,987 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel 8,670 see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 8,670 N/A 8,670 9,537 10,404 11,271 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 8,670 N/A 8,670 9,537 10,404 11,271 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 8,670 N/A 8,670 9,537 10,404 11,271 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm see below N/A see below #VALUE! #VALUE! #VALUE! 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 8,670 N/A 8,670 9,537 10,404 11,271 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm see below N/A see below #VALUE! #VALUE! #VALUE! 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 8,690 N/A 8,690 9,559 10,428 11,297 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 8,690 N/A 8,690 9,559 10,428 11,297 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 8,630 N/A 8,630 9,493 10,356 11,219 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 8,690 N/A 8,690 9,559 10,428 11,297 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" see below N/A see below #VALUE! #VALUE! #VALUE! 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 8,690 N/A 8,690 9,559 10,428 11,297 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils see below N/A see below #VALUE! #VALUE! #VALUE! 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 10 N/A 10 11 12 13 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 10 N/A 10 11 12 13 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 10 N/A 10 11 12 13 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 10 N/A 10 11 12 13 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 10 N/A 10 11 12 13 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 10 N/A 10 11 12 13 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 2,280 N/A 2,280 2,508 2,736 2,964 (F) 7224 90 02 Semi-finished products of tool steel 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 2,280 N/A 2,280 2,508 2,736 2,964 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 2,280 N/A 2,280 2,508 2,736 2,964 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 2,830 N/A 2,830 3,113 3,396 3,679 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 2,364 N/A 2,364 2,600 2,837 3,073 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 2,364 N/A 2,364 2,600 2,837 3,073 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 2,830 N/A 2,830 3,113 3,396 3,679 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 2,150 N/A 2,150 2,365 2,580 2,795 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 2,150 N/A 2,150 2,365 2,580 2,795 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 2,170 N/A 2,170 2,387 2,604 2,821 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,280 N/A 2,280 2,508 2,736 2,964 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,170 N/A 2,170 2,387 2,604 2,821 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,280 N/A 2,280 2,508 2,736 2,964 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,170 N/A 2,170 2,387 2,604 2,821 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 2,170 N/A 2,170 2,387 2,604 2,821 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 2,170 N/A 2,170 2,387 2,604 2,821 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,383 N/A 2,383 2,621 2,860 3,098 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,473 N/A 2,473 2,720 2,968 3,215 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 2,513 N/A 2,513 2,764 3,016 3,267 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 2,513 N/A 2,513 2,764 3,016 3,267 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 2,513 N/A 2,513 2,764 3,016 3,267 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,513 N/A 2,513 2,764 3,016 3,267 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 2,513 N/A 2,513 2,764 3,016 3,267 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,233 N/A 2,233 2,456 2,680 2,903 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,233 N/A 2,233 2,456 2,680 2,903 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,543 N/A 2,543 2,797 3,052 3,306 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 2,543 N/A 2,543 2,797 3,052 3,306 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,313 N/A 2,313 2,544 2,776 3,007 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,543 N/A 2,543 2,797 3,052 3,306 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 2,523 N/A 2,523 2,775 3,028 3,280 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,273 N/A 2,273 2,500 2,728 2,955 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,253 N/A 2,253 2,478 2,704 2,929 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,273 N/A 2,273 2,500 2,728 2,955 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 2,543 N/A 2,543 2,797 3,052 3,306 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,543 N/A 2,543 2,797 3,052 3,306 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,373 N/A 2,373 2,610 2,848 3,085 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,373 N/A 2,373 2,610 2,848 3,085 7307 19 90 Cast tube or pipe fittings of steel 2,453 N/A 2,453 2,698 2,944 3,189 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,543 N/A 2,543 2,797 3,052 3,306 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,543 N/A 2,543 2,797 3,052 3,306 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,543 N/A 2,543 2,797 3,052 3,306 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,543 N/A 2,543 2,797 3,052 3,306 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,313 N/A 2,313 2,544 2,776 3,007 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,443 N/A 2,443 2,687 2,932 3,176 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,333 N/A 2,333 2,566 2,800 3,033 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 16 Nuts of iron or steel 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,707 N/A 2,707 2,978 3,249 3,519 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,453 N/A 2,453 2,698 2,944 3,189 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,453 N/A 2,453 2,698 2,944 3,189 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,303 N/A 2,303 2,533 2,764 2,994 (C) 7326 90 30 Ladders and steps, of iron or steel 2,303 N/A 2,303 2,533 2,764 2,994 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,303 N/A 2,303 2,533 2,764 2,994 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,303 N/A 2,303 2,533 2,764 2,994 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,303 N/A 2,303 2,533 2,764 2,994 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,453 N/A 2,453 2,698 2,944 3,189 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,453 N/A 2,453 2,698 2,944 3,189 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,453 N/A 2,453 2,698 2,944 3,189 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,333 N/A 2,333 2,566 2,800 3,033 (C) Tajikistan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0 1,360 1,496 1,632 1,768 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,360 0,010 1,360 1,496 1,632 1,768 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,290 0,010 1,300 1,430 1,560 1,690 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,700 0,040 2,740 2,767 2,767 2,767 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,650 0,040 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 2,180 0,050 2,230 2,252 2,252 2,252 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,030 0,490 0,495 0,495 0,495 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,030 0,800 0,808 0,808 0,808 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,080 1,490 1,505 1,505 1,505 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,080 1,450 1,465 1,465 1,465 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,040 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,390 0,050 1,440 1,454 1,454 1,454 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,650 0,040 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,540 0,060 2,600 2,626 2,626 2,626 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,050 2,210 2,232 2,232 2,232 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,050 2,210 2,232 2,232 2,232 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,220 0,060 4,280 4,323 4,323 4,323 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,050 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,580 0,050 1,630 1,646 1,646 1,646 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,610 0,060 1,670 1,687 1,687 1,687 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,040 0,840 0,848 0,848 0,848 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,060 0,030 1,090 1,101 1,101 1,101 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,020 0,740 0,747 0,747 0,747 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,030 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,020 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,460 0,040 1,500 1,515 1,515 1,515 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,070 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,040 1,470 1,485 1,485 1,485 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,020 0,750 0,758 0,758 0,758 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Tanzania Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,030 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,850 0,050 0,900 0,990 1,080 1,170 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,810 0,050 0,860 0,946 1,032 1,118 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,640 0,050 1,680 1,697 1,697 1,697 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,600 0,050 0,650 0,657 0,657 0,657 2834 21 00 Nitrate of potassium 1,460 0,070 1,520 1,535 1,535 1,535 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,440 0,040 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,730 0,040 0,770 0,778 0,778 0,778 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,330 0,110 1,440 1,454 1,454 1,454 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,300 0,100 1,410 1,424 1,424 1,424 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,580 0,070 0,650 0,657 0,657 0,657 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,040 0,080 1,120 1,131 1,131 1,131 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,110 0,060 1,170 1,182 1,182 1,182 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,700 0,100 1,800 1,818 1,818 1,818 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,090 1,550 1,566 1,566 1,566 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,470 0,090 1,550 1,566 1,566 1,566 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,560 0,070 2,630 2,656 2,656 2,656 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,080 1,510 1,525 1,525 1,525 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,180 0,080 1,260 1,273 1,273 1,273 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,300 0,090 1,390 1,404 1,404 1,404 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,620 0,070 0,680 0,687 0,687 0,687 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,740 0,080 0,820 0,828 0,828 0,828 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,060 0,560 0,566 0,566 0,566 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,470 0,050 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,010 0,100 1,100 1,111 1,111 1,111 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,090 0,630 0,636 0,636 0,636 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,060 1,040 1,050 1,050 1,050 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,510 0,040 0,550 0,556 0,556 0,556 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,600 N/A 0,600 0,660 0,720 0,780 (L) 7604 10 10 Bars and rods 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7604 10 90 Profiles 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7604 21 00 Hollow profiles 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7604 29 10 Bars and rods 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7604 29 90 Profiles 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7605 Aluminium wire 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7608 Aluminium tubes and pipes 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7610 90 Other 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7610 90 90 Other 0,840 N/A 0,840 0,924 1,008 1,092 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,280 N/A 1,280 1,408 1,536 1,664 (L) 7616 99 10 Cast 0,600 N/A 0,600 0,660 0,720 0,780 (L) 7616 99 90 Other 1,280 N/A 1,280 1,408 1,536 1,664 (L) Thailand Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,080 0,060 2,130 2,151 2,151 2,151 2814 10 00 Anhydrous ammonia 2,060 0,180 2,240 2,262 2,262 2,262 2814 20 00 Ammonia in aqueous solution 0,620 0,050 0,670 0,677 0,677 0,677 2834 21 00 Nitrate of potassium 1,760 0,080 1,840 1,858 1,858 1,858 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,050 0,510 0,515 0,515 0,515 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,050 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,400 0,140 1,540 1,555 1,555 1,555 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,370 0,140 1,510 1,525 1,525 1,525 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,100 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,190 0,120 1,310 1,323 1,323 1,323 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,330 0,090 1,420 1,434 1,434 1,434 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,050 0,140 2,190 2,212 2,212 2,212 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,770 0,130 1,890 1,909 1,909 1,909 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,770 0,130 1,890 1,909 1,909 1,909 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,240 0,090 3,330 3,363 3,363 3,363 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,720 0,120 1,840 1,858 1,858 1,858 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,360 0,110 1,470 1,485 1,485 1,485 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,450 0,130 1,580 1,596 1,596 1,596 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,700 0,110 0,800 0,808 0,808 0,808 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,880 0,130 1,010 1,020 1,020 1,020 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,100 0,700 0,707 0,707 0,707 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,080 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,060 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,200 0,160 1,360 1,374 1,374 1,374 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,560 0,120 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,170 0,100 1,260 1,273 1,273 1,273 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,600 0,070 0,670 0,677 0,677 0,677 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,050 N/A 1,050 1,155 1,260 1,365 (L) 7604 10 10 Bars and rods 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7604 10 90 Profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 21 00 Hollow profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 29 10 Bars and rods 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7604 29 90 Profiles 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7605 Aluminium wire 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7608 Aluminium tubes and pipes 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 Other 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7610 90 90 Other 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,730 N/A 1,730 1,903 2,076 2,249 (L) 7616 99 10 Cast 1,050 N/A 1,050 1,155 1,260 1,365 (L) 7616 99 90 Other 1,730 N/A 1,730 1,903 2,076 2,249 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 1,130 0,070 1,190 1,309 1,428 1,547 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms - N/A - - - - 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,430 N/A 1,430 1,573 1,716 1,859 (E) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 0,210 N/A 0,210 0,231 0,252 0,273 (E) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 0,210 N/A 0,210 0,231 0,252 0,273 (E) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,331 N/A 2,331 2,564 2,797 3,030 (E) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,331 N/A 2,331 2,564 2,797 3,030 (E) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,331 N/A 2,331 2,564 2,797 3,030 (E) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,331 N/A 2,331 2,564 2,797 3,030 (E) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,331 N/A 2,331 2,564 2,797 3,030 (E) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,331 N/A 2,331 2,564 2,797 3,030 (E) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 1,440 N/A 1,440 1,584 1,728 1,872 (E) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel - - - - - - 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) - - - - - - 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section - - - - - - 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting - - - - - - 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged - - - - - - 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting - - - - - - 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) - - - - - - 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" - - - - - - 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm - - - - - - 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm - - - - - - 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm - - - - - - 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm - - - - - - 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm - - - - - - 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm - - - - - - 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm - - - - - - 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm - - - - - - 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm - - - - - - 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm - - - - - - 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm - - - - - - 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm - - - - - - 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm - - - - - - 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked - - - - - - 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" - - - - - - 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm - - - - - - 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm - - - - - - 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" - - - - - - 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked - - - - - - 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils - - - - - - 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. - - - - - - 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section - - - - - - 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) - - - - - - 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished - - - - - - 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. - - - - - - 7222 40 Angles, shapes and sections of stainless steel, n.e.s. - - - - - - 7223 Wire of stainless steel, in coils (excl. bars and rods) - - - - - - 7223 00 Wire of stainless steel, in coils (excl. bars and rods) - - - - - - 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7224 90 02 Semi-finished products of tool steel 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,660 N/A 4,660 5,126 5,592 6,058 (E) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,520 N/A 3,520 3,872 4,224 4,576 (E) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,660 N/A 4,660 5,126 5,592 6,058 (E) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,520 N/A 3,520 3,872 4,224 4,576 (E) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,520 N/A 3,520 3,872 4,224 4,576 (H) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,570 N/A 3,570 3,927 4,284 4,641 (H) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,580 N/A 3,580 3,938 4,296 4,654 (E)/(H) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,580 N/A 3,580 3,938 4,296 4,654 (H) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,580 N/A 3,580 3,938 4,296 4,654 (H) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,580 N/A 3,580 3,938 4,296 4,654 (H) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,580 N/A 3,580 3,938 4,296 4,654 (E)/(H) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,390 N/A 3,390 3,729 4,068 4,407 (H) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,580 N/A 3,580 3,938 4,296 4,654 (E)/(H) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,580 N/A 3,580 3,938 4,296 4,654 (H) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,580 N/A 3,580 3,938 4,296 4,654 (H) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,580 N/A 3,580 3,938 4,296 4,654 (H) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,580 N/A 3,580 3,938 4,296 4,654 (E)/(H) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,040 N/A 2,040 2,243 2,447 2,651 (E) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,950 N/A 3,950 4,344 4,739 5,134 (E) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 3,070 N/A 3,070 3,376 3,683 3,990 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 4,630 N/A 4,630 5,092 5,555 6,018 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 1,960 N/A 1,960 2,155 2,351 2,547 (E) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 4,630 N/A 4,630 5,092 5,555 6,018 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 1,960 N/A 1,960 2,155 2,351 2,547 (E) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 4,630 N/A 4,630 5,092 5,555 6,018 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 1,960 N/A 1,960 2,155 2,351 2,547 (E) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 1,960 N/A 1,960 2,155 2,351 2,547 (E) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 1,960 N/A 1,960 2,155 2,351 2,547 (E) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 4,630 N/A 4,630 5,092 5,555 6,018 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 4,630 N/A 4,630 5,092 5,555 6,018 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,950 N/A 1,950 2,144 2,339 2,534 (H) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,950 N/A 1,950 2,144 2,339 2,534 (E)/(H) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 1,960 N/A 1,960 2,155 2,351 2,547 (E) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,810 N/A 4,810 5,290 5,771 6,252 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 4,810 N/A 4,810 5,290 5,771 6,252 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,030 N/A 2,030 2,232 2,435 2,638 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,810 N/A 4,810 5,290 5,771 6,252 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 4,750 N/A 4,750 5,224 5,699 6,174 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,130 N/A 2,130 2,342 2,555 2,768 (H) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,080 N/A 2,080 2,287 2,495 2,703 (H) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,130 N/A 2,130 2,342 2,555 2,768 (H) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 4,810 N/A 4,810 5,290 5,771 6,252 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,810 N/A 4,810 5,290 5,771 6,252 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,080 N/A 2,080 2,287 2,495 2,703 (E) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,070 N/A 3,070 3,376 3,683 3,990 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,070 N/A 3,070 3,376 3,683 3,990 7307 19 90 Cast tube or pipe fittings of steel 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7307 21 00 Flanges of stainless steel (excl. cast products) 4,110 N/A 4,110 4,520 4,931 5,342 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 4,110 N/A 4,110 4,520 4,931 5,342 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 4,110 N/A 4,110 4,520 4,931 5,342 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 4,110 N/A 4,110 4,520 4,931 5,342 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 4,290 N/A 4,290 4,718 5,147 5,576 (E) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 4,640 N/A 4,640 5,103 5,567 6,031 (E) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,090 N/A 2,090 2,298 2,507 2,716 (E) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 4,570 N/A 4,570 5,026 5,483 5,940 (E) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 4,690 N/A 4,690 5,158 5,627 6,096 (E) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 4,690 N/A 4,690 5,158 5,627 6,096 (E) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 16 Nuts of iron or steel 4,450 N/A 4,450 4,894 5,339 5,784 (E) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 24 00 Cotters and cotter pins, of iron or steel 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7318 29 00 Non-threaded articles, of iron or steel 2,408 N/A 2,408 2,649 2,890 3,130 (E) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7326 20 00 Articles of iron or steel wire, n.e.s. 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7326 90 30 Ladders and steps, of iron or steel 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7326 90 50 Reels for cables, piping and the like, of iron or steel 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 1,920 N/A 1,920 2,111 2,303 2,495 (E) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7326 90 96 Sintered articles of iron or steel, n.e.s. 1,850 N/A 1,850 2,034 2,219 2,404 (E) 7326 90 98 Articles of iron or steel, n.e.s. 1,980 N/A 1,980 2,177 2,375 2,573 (E) Togo Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,850 0,030 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,950 0,060 1 1,100 1,200 1,300 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,900 0,060 0,960 1,056 1,152 1,248 (A) 2523 30 00 Aluminous cement - - - - - - Trinidad and Tobago Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,870 0,040 0,910 1,001 1,092 1,183 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,870 0,070 0,950 1,045 1,140 1,235 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,840 0,080 0,910 1,001 1,092 1,183 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,870 0,050 1,920 1,939 1,939 1,939 2814 10 00 Anhydrous ammonia 2,260 0,150 2,420 2,444 2,444 2,444 2814 20 00 Ammonia in aqueous solution 0,680 0,050 0,730 0,737 0,737 0,737 2834 21 00 Nitrate of potassium 1,640 0,070 1,710 1,727 1,727 1,727 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,500 0,040 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,820 0,040 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,490 0,120 1,610 1,626 1,626 1,626 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,460 0,110 1,570 1,586 1,586 1,586 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,080 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,140 0,100 1,240 1,252 1,252 1,252 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,240 0,070 1,310 1,323 1,323 1,323 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,910 0,110 2,020 2,040 2,040 2,040 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,610 0,100 1,720 1,737 1,737 1,737 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,610 0,100 1,720 1,737 1,737 1,737 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,920 0,080 3 3,030 3,030 3,030 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,600 0,100 1,700 1,717 1,717 1,717 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,330 0,090 1,420 1,434 1,434 1,434 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,440 0,110 1,550 1,566 1,566 1,566 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,670 0,090 0,760 0,768 0,768 0,768 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,810 0,100 0,910 0,919 0,919 0,919 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,080 0,630 0,636 0,636 0,636 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,060 0,580 0,586 0,586 0,586 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,330 0,050 0,380 0,384 0,384 0,384 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,100 0,130 1,230 1,242 1,242 1,242 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,100 0,670 0,677 0,677 0,677 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,080 1,170 1,182 1,182 1,182 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,050 0,610 0,616 0,616 0,616 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Tunisia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,290 0,050 1,330 1,463 1,596 1,729 (B) 2523 10 00 Grey clinker 0,850 0,030 0,880 0,968 1,056 1,144 (A) 2523 21 00 White Portland cement 1,260 0,140 1,390 1,529 1,668 1,807 2523 29 00 Grey Portland cement 0,860 0,060 0,910 1,001 1,092 1,183 2523 90 00 White hydraulic cements 1,300 0,160 1,460 1,606 1,752 1,898 (B) 2523 90 00 Grey hydraulic cements 0,820 0,060 0,880 0,968 1,056 1,144 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,570 0,030 2,600 2,626 2,626 2,626 2814 10 00 Anhydrous ammonia 2 0,100 2,100 2,121 2,121 2,121 2814 20 00 Ammonia in aqueous solution 0,600 0,030 0,630 0,636 0,636 0,636 2834 21 00 Nitrate of potassium 2,070 0,050 2,120 2,141 2,141 2,141 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,030 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,030 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,380 0,080 1,460 1,475 1,475 1,475 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,340 0,080 1,430 1,444 1,444 1,444 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,060 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,330 0,070 1,400 1,414 1,414 1,414 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,570 0,050 1,620 1,636 1,636 1,636 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,410 0,080 2,490 2,515 2,515 2,515 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,070 0,080 2,150 2,172 2,172 2,172 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,070 0,080 2,150 2,172 2,172 2,172 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,010 0,050 4,060 4,101 4,101 4,101 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,020 0,070 2,090 2,111 2,111 2,111 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,510 0,060 1,580 1,596 1,596 1,596 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,550 0,080 1,630 1,646 1,646 1,646 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,760 0,060 0,830 0,838 0,838 0,838 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,010 0,080 1,090 1,101 1,101 1,101 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,690 0,060 0,750 0,758 0,758 0,758 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,470 0,050 0,520 0,525 0,525 0,525 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,040 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,400 0,100 1,490 1,505 1,505 1,505 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,090 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,360 0,060 1,420 1,434 1,434 1,434 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,700 0,040 0,740 0,747 0,747 0,747 Aluminium 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,760 N/A 0,760 0,836 0,912 0,988 (L) 7604 10 10 Bars and rods 0,980 N/A 0,980 1,078 1,176 1,274 (L) 7604 10 90 Profiles 1 N/A 1 1,100 1,200 1,300 (L) 7604 21 00 Hollow profiles 1 N/A 1 1,100 1,200 1,300 (L) 7604 29 10 Bars and rods 0,980 N/A 0,980 1,078 1,176 1,274 (L) 7604 29 90 Profiles 1 N/A 1 1,100 1,200 1,300 (L) 7605 Aluminium wire 0,980 N/A 0,980 1,078 1,176 1,274 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7608 Aluminium tubes and pipes 1 N/A 1 1,100 1,200 1,300 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1 N/A 1 1,100 1,200 1,300 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1 N/A 1 1,100 1,200 1,300 (L) 7610 90 Other 1 N/A 1 1,100 1,200 1,300 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1 N/A 1 1,100 1,200 1,300 (L) 7610 90 90 Other 1 N/A 1 1,100 1,200 1,300 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,980 N/A 0,980 1,078 1,176 1,274 (L) 7615 10 10 Cast 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7615 10 30 Manufactured from foil of a thickness not exceeding 0,2 mm 1,440 N/A 1,440 1,584 1,728 1,872 (L) 7615 10 80 Other 0,760 N/A 0,760 0,836 0,912 0,988 (L) 7615 20 00 Sanitary ware and parts thereof 1,440 N/A 1,440 1,584 1,728 1,872 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Türkiye Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker - - - - - - 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement - - - - - - 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements - - - - - - 2523 30 00 Aluminous cement 1,820 0,140 1,950 2,145 2,340 2,535 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,680 0,030 2,720 2,747 2,747 2,747 2814 10 00 Anhydrous ammonia 2,170 0,100 2,270 2,293 2,293 2,293 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,170 0,050 2,220 2,242 2,242 2,242 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,480 0,020 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,790 0,020 0,820 0,828 0,828 0,828 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,440 0,080 1,510 1,525 1,525 1,525 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,400 0,080 1,480 1,495 1,495 1,495 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,630 0,060 0,680 0,687 0,687 0,687 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,400 0,060 1,460 1,475 1,475 1,475 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,050 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,530 0,070 2,600 2,626 2,626 2,626 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,070 2,230 2,252 2,252 2,252 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,160 0,070 2,230 2,252 2,252 2,252 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,190 0,050 4,240 4,282 4,282 4,282 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,060 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,580 0,060 1,640 1,656 1,656 1,656 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,620 0,070 1,690 1,707 1,707 1,707 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,060 0,860 0,869 0,869 0,869 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,060 0,060 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,720 0,050 0,770 0,778 0,778 0,778 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,040 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,030 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,460 0,080 1,540 1,555 1,555 1,555 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,580 0,080 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,050 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,040 0,760 0,768 0,768 0,768 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 3,369 N/A 3,369 3,706 4,043 4,380 (K) 7604 10 10 Bars and rods 3,741 N/A 3,741 4,116 4,490 4,864 (K) 7604 10 90 Profiles 3,741 N/A 3,741 4,116 4,490 4,864 (K) 7604 21 00 Hollow profiles 3,741 N/A 3,741 4,116 4,490 4,864 (K) 7604 29 10 Bars and rods 3,741 N/A 3,741 4,116 4,490 4,864 (K) 7604 29 90 Profiles 3,741 N/A 3,741 4,116 4,490 4,864 (K) 7605 Aluminium wire 3,424 N/A 3,424 3,766 4,109 4,451 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,714 N/A 2,714 2,985 3,257 3,528 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 3,071 N/A 3,071 3,378 3,685 3,992 (K) 7608 Aluminium tubes and pipes 2,754 N/A 2,754 3,029 3,304 3,580 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 3,775 N/A 3,775 4,153 4,530 4,908 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,674 N/A 2,674 2,941 3,209 3,476 (K) 7610 90 Other 2,674 N/A 2,674 2,941 3,209 3,476 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,674 N/A 2,674 2,941 3,209 3,476 (K) 7610 90 90 Other 2,674 N/A 2,674 2,941 3,209 3,476 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,520 N/A 4,520 4,972 5,424 5,876 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,520 N/A 4,520 4,972 5,424 5,876 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 4,520 N/A 4,520 4,972 5,424 5,876 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 3,741 N/A 3,741 4,116 4,490 4,864 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 3,060 N/A 3,060 3,366 3,672 3,978 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 3,060 N/A 3,060 3,366 3,672 3,978 (K) 7616 99 10 Cast 3,060 N/A 3,060 3,366 3,672 3,978 (K) 7616 99 90 Other 3,060 N/A 3,060 3,366 3,672 3,978 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,180 0,030 0,210 0,231 0,252 0,273 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,850 N/A 1,850 2,035 2,220 2,405 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,890 N/A 1,890 2,079 2,268 2,457 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,960 N/A 1,960 2,156 2,352 2,548 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,960 N/A 1,960 2,156 2,352 2,548 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,428 N/A 2,428 2,670 2,913 3,156 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,428 N/A 2,428 2,670 2,913 3,156 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,428 N/A 2,428 2,670 2,913 3,156 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,428 N/A 2,428 2,670 2,913 3,156 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 3,087 N/A 3,087 3,396 3,705 4,014 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 5,970 N/A 5,970 6,567 7,164 7,761 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 5,470 N/A 5,470 6,017 6,564 7,111 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 5,470 N/A 5,470 6,017 6,564 7,111 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 5,970 N/A 5,970 6,567 7,164 7,761 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 5,470 N/A 5,470 6,017 6,564 7,111 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 5,970 N/A 5,970 6,567 7,164 7,761 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 5,470 N/A 5,470 6,017 6,564 7,111 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 5,540 N/A 5,540 6,094 6,648 7,202 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 5,540 N/A 5,540 6,094 6,648 7,202 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 5,540 N/A 5,540 6,094 6,648 7,202 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 5,540 N/A 5,540 6,094 6,648 7,202 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 5,540 N/A 5,540 6,094 6,648 7,202 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 5,540 N/A 5,540 6,094 6,648 7,202 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 5,470 N/A 5,470 6,017 6,564 7,111 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 5,470 N/A 5,470 6,017 6,564 7,111 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 5,540 N/A 5,540 6,094 6,648 7,202 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 5,540 N/A 5,540 6,094 6,648 7,202 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 5,310 N/A 5,310 5,841 6,372 6,903 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 5,310 N/A 5,310 5,841 6,372 6,903 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 5,310 N/A 5,310 5,841 6,372 6,903 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 5,310 N/A 5,310 5,841 6,372 6,903 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 5,970 N/A 5,970 6,567 7,164 7,761 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 5,310 N/A 5,310 5,841 6,372 6,903 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 5,310 N/A 5,310 5,841 6,372 6,903 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 6,950 N/A 6,950 7,645 8,340 9,035 (F) 7224 90 02 Semi-finished products of tool steel 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 6,950 N/A 6,950 7,645 8,340 9,035 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 6,950 N/A 6,950 7,645 8,340 9,035 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 8,500 N/A 8,500 9,350 10,200 11,050 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 6,450 N/A 6,450 7,095 7,740 8,385 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 8,500 N/A 8,500 9,350 10,200 11,050 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 6,450 N/A 6,450 7,095 7,740 8,385 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 6,450 N/A 6,450 7,095 7,740 8,385 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 6,520 N/A 6,520 7,172 7,824 8,476 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 6,290 N/A 6,290 6,919 7,548 8,177 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,290 N/A 6,290 6,919 7,548 8,177 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,950 N/A 6,950 7,645 8,340 9,035 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,290 N/A 6,290 6,919 7,548 8,177 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,290 N/A 6,290 6,919 7,548 8,177 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,290 N/A 6,290 6,919 7,548 8,177 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,950 N/A 6,950 7,645 8,340 9,035 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,290 N/A 6,290 6,919 7,548 8,177 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 6,290 N/A 6,290 6,919 7,548 8,177 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 6,290 N/A 6,290 6,919 7,548 8,177 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 6,290 N/A 6,290 6,919 7,548 8,177 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 6,290 N/A 6,290 6,919 7,548 8,177 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,510 N/A 2,510 2,761 3,012 3,263 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 5,360 N/A 5,360 5,896 6,432 6,968 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,480 N/A 2,480 2,728 2,976 3,224 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 5,690 N/A 5,690 6,259 6,828 7,397 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 5,690 N/A 5,690 6,259 6,828 7,397 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 5,690 N/A 5,690 6,259 6,828 7,397 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 5,690 N/A 5,690 6,259 6,828 7,397 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 5,690 N/A 5,690 6,259 6,828 7,397 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,360 N/A 2,360 2,596 2,832 3,068 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,360 N/A 2,360 2,596 2,832 3,068 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,340 N/A 2,340 2,574 2,808 3,042 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,182 N/A 2,182 2,400 2,618 2,837 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 5,920 N/A 5,920 6,512 7,104 7,696 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 5,920 N/A 5,920 6,512 7,104 7,696 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,244 N/A 2,244 2,468 2,693 2,917 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 5,920 N/A 5,920 6,512 7,104 7,696 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 5,850 N/A 5,850 6,435 7,020 7,605 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,244 N/A 2,244 2,468 2,693 2,917 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,244 N/A 2,244 2,468 2,693 2,917 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,244 N/A 2,244 2,468 2,693 2,917 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 5,920 N/A 5,920 6,512 7,104 7,696 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 5,920 N/A 5,920 6,512 7,104 7,696 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,244 N/A 2,244 2,468 2,693 2,917 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,151 N/A 3,151 3,466 3,781 4,096 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,151 N/A 3,151 3,466 3,781 4,096 7307 19 90 Cast tube or pipe fittings of steel 3,151 N/A 3,151 3,466 3,781 4,096 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 3,710 N/A 3,710 4,081 4,452 4,823 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3,710 N/A 3,710 4,081 4,452 4,823 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3,710 N/A 3,710 4,081 4,452 4,823 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3,710 N/A 3,710 4,081 4,452 4,823 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 3,151 N/A 3,151 3,466 3,781 4,096 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 3,151 N/A 3,151 3,466 3,781 4,096 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 3,151 N/A 3,151 3,466 3,781 4,096 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 3,151 N/A 3,151 3,466 3,781 4,096 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 5,520 N/A 5,520 6,072 6,624 7,176 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 5,600 N/A 5,600 6,160 6,720 7,280 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 3,030 N/A 3,030 3,333 3,636 3,939 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 5,430 N/A 5,430 5,973 6,516 7,059 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 5,690 N/A 5,690 6,259 6,828 7,397 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 5,690 N/A 5,690 6,259 6,828 7,397 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 5,430 N/A 5,430 5,973 6,516 7,059 (C) 7318 16 Nuts of iron or steel 3,790 N/A 3,790 4,169 4,548 4,927 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 3,430 N/A 3,430 3,773 4,116 4,459 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,832 N/A 2,832 3,115 3,398 3,682 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 3 N/A 3 3,300 3,600 3,900 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 3 N/A 3 3,300 3,600 3,900 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,583 N/A 2,583 2,841 3,100 3,358 (C) 7326 90 30 Ladders and steps, of iron or steel 2,583 N/A 2,583 2,841 3,100 3,358 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,583 N/A 2,583 2,841 3,100 3,358 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,583 N/A 2,583 2,841 3,100 3,358 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,583 N/A 2,583 2,841 3,100 3,358 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 3 N/A 3 3,300 3,600 3,900 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,583 N/A 2,583 2,841 3,100 3,358 (C) Turkmenistan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0,050 1,400 1,540 1,680 1,820 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,360 0,090 1,440 1,584 1,728 1,872 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,290 0,090 1,380 1,518 1,656 1,794 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,690 0,070 2,760 2,788 2,788 2,788 2814 10 00 Anhydrous ammonia 2,160 0,210 2,370 2,394 2,394 2,394 2814 20 00 Ammonia in aqueous solution 0,650 0,060 0,710 0,717 0,717 0,717 2834 21 00 Nitrate of potassium 2,170 0,100 2,270 2,293 2,293 2,293 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,470 0,050 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,050 0,830 0,838 0,838 0,838 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,410 0,160 1,570 1,586 1,586 1,586 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,380 0,160 1,530 1,545 1,545 1,545 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,120 0,740 0,747 0,747 0,747 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,390 0,130 1,520 1,535 1,535 1,535 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,100 1,750 1,768 1,768 1,768 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,530 0,160 2,690 2,717 2,717 2,717 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,140 2,300 2,323 2,323 2,323 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,140 2,300 2,323 2,323 2,323 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,200 0,100 4,310 4,353 4,353 4,353 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,140 2,260 2,283 2,283 2,283 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,580 0,120 1,700 1,717 1,717 1,717 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,600 0,150 1,750 1,768 1,768 1,768 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,120 0,920 0,929 0,929 0,929 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,140 1,200 1,212 1,212 1,212 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,110 0,820 0,828 0,828 0,828 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,090 0,590 0,596 0,596 0,596 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,070 0,390 0,394 0,394 0,394 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,450 0,180 1,630 1,646 1,646 1,646 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,130 0,710 0,717 0,717 0,717 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,110 1,540 1,555 1,555 1,555 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,080 0,810 0,818 0,818 0,818 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Uganda Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,950 0,010 0,950 1,045 1,140 1,235 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,990 0,020 1,010 1,111 1,212 1,313 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,940 0,030 0,970 1,067 1,164 1,261 (A) 2523 30 00 Aluminous cement - - - - - - Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,510 N/A 0,510 0,561 0,612 0,663 (L) 7604 10 10 Bars and rods 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 10 90 Profiles 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7604 21 00 Hollow profiles 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7604 29 10 Bars and rods 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 29 90 Profiles 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7605 Aluminium wire 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7608 Aluminium tubes and pipes 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 90 Other 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7610 90 90 Other 0,750 N/A 0,750 0,825 0,900 0,975 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,190 N/A 1,190 1,309 1,428 1,547 (L) 7616 99 10 Cast 0,510 N/A 0,510 0,561 0,612 0,663 (L) 7616 99 90 Other 1,190 N/A 1,190 1,309 1,428 1,547 (L) Ukraine Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,340 0,030 1,370 1,507 1,644 1,781 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,340 0,050 1,380 1,518 1,656 1,794 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,270 0,050 1,320 1,452 1,584 1,716 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,700 0,030 2,730 2,757 2,757 2,757 2814 10 00 Anhydrous ammonia 2,160 0,090 2,250 2,273 2,273 2,273 2814 20 00 Ammonia in aqueous solution 0,650 0,030 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 2,180 0,040 2,220 2,242 2,242 2,242 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,020 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,020 0,780 0,788 0,788 0,788 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,380 0,070 1,450 1,465 1,465 1,465 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,350 0,070 1,420 1,434 1,434 1,434 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,620 0,050 0,670 0,677 0,677 0,677 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,390 0,060 1,450 1,465 1,465 1,465 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,640 0,040 1,690 1,707 1,707 1,707 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,530 0,070 2,600 2,626 2,626 2,626 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,060 2,220 2,242 2,242 2,242 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,060 2,220 2,242 2,242 2,242 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,220 0,050 4,270 4,313 4,313 4,313 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,120 0,060 2,180 2,202 2,202 2,202 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,570 0,060 1,630 1,646 1,646 1,646 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,590 0,060 1,660 1,677 1,677 1,677 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,800 0,050 0,850 0,859 0,859 0,859 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,050 0,060 1,120 1,131 1,131 1,131 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,050 0,760 0,768 0,768 0,768 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,040 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,030 0,350 0,354 0,354 0,354 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,450 0,080 1,530 1,545 1,545 1,545 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,570 0,080 0,640 0,646 0,646 0,646 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,430 0,050 1,480 1,495 1,495 1,495 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,730 0,030 0,760 0,768 0,768 0,768 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,490 N/A 0,490 0,539 0,588 0,637 (L) 7604 10 10 Bars and rods 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7604 10 90 Profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 21 00 Hollow profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7604 29 10 Bars and rods 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7604 29 90 Profiles 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7605 Aluminium wire 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7608 Aluminium tubes and pipes 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 Other 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7610 90 90 Other 0,730 N/A 0,730 0,803 0,876 0,949 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,180 N/A 1,180 1,298 1,416 1,534 (L) 7616 99 10 Cast 0,490 N/A 0,490 0,539 0,588 0,637 (L) 7616 99 90 Other 1,180 N/A 1,180 1,298 1,416 1,534 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,080 0,050 0,120 0,132 0,144 0,156 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,173 N/A 2,173 2,390 2,608 2,825 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 1,910 N/A 1,910 2,101 2,292 2,483 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,970 N/A 1,970 2,167 2,364 2,561 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,970 N/A 1,970 2,167 2,364 2,561 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,483 N/A 2,483 2,731 2,979 3,227 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,544 N/A 2,544 2,798 3,052 3,307 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,544 N/A 2,544 2,798 3,052 3,307 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,483 N/A 2,483 2,731 2,979 3,227 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,483 N/A 2,483 2,731 2,979 3,227 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,483 N/A 2,483 2,731 2,979 3,227 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,544 N/A 2,544 2,798 3,052 3,307 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,544 N/A 2,544 2,798 3,052 3,307 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,544 N/A 2,544 2,798 3,052 3,307 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,544 N/A 2,544 2,798 3,052 3,307 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,397 N/A 2,397 2,637 2,877 3,117 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,110 N/A 3,110 3,421 3,732 4,043 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,230 N/A 3,230 3,553 3,876 4,199 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,230 N/A 3,230 3,553 3,876 4,199 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,230 N/A 3,230 3,553 3,876 4,199 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,230 N/A 3,230 3,553 3,876 4,199 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,280 N/A 3,280 3,608 3,936 4,264 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,280 N/A 3,280 3,608 3,936 4,264 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,280 N/A 3,280 3,608 3,936 4,264 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,280 N/A 3,280 3,608 3,936 4,264 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,280 N/A 3,280 3,608 3,936 4,264 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,280 N/A 3,280 3,608 3,936 4,264 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,230 N/A 3,230 3,553 3,876 4,199 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,230 N/A 3,230 3,553 3,876 4,199 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,280 N/A 3,280 3,608 3,936 4,264 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,280 N/A 3,280 3,608 3,936 4,264 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,110 N/A 3,110 3,421 3,732 4,043 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,110 N/A 3,110 3,421 3,732 4,043 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,110 N/A 3,110 3,421 3,732 4,043 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,110 N/A 3,110 3,421 3,732 4,043 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,110 N/A 3,110 3,421 3,732 4,043 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,110 N/A 3,110 3,421 3,732 4,043 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7224 90 02 Semi-finished products of tool steel 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,650 N/A 4,650 5,115 5,580 6,045 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,540 N/A 3,540 3,894 4,248 4,602 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,650 N/A 4,650 5,115 5,580 6,045 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,540 N/A 3,540 3,894 4,248 4,602 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,540 N/A 3,540 3,894 4,248 4,602 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,420 N/A 3,420 3,762 4,104 4,446 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,420 N/A 3,420 3,762 4,104 4,446 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,543 N/A 2,543 2,797 3,052 3,306 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,213 N/A 3,213 3,534 3,856 4,177 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,183 N/A 2,183 2,401 2,620 2,838 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,563 N/A 3,563 3,919 4,276 4,632 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,596 N/A 2,596 2,856 3,116 3,375 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,563 N/A 3,563 3,919 4,276 4,632 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,596 N/A 2,596 2,856 3,116 3,375 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,563 N/A 3,563 3,919 4,276 4,632 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,596 N/A 2,596 2,856 3,116 3,375 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,596 N/A 2,596 2,856 3,116 3,375 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,596 N/A 2,596 2,856 3,116 3,375 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,563 N/A 3,563 3,919 4,276 4,632 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,563 N/A 3,563 3,919 4,276 4,632 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,596 N/A 2,596 2,856 3,116 3,375 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,596 N/A 2,596 2,856 3,116 3,375 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,596 N/A 2,596 2,856 3,116 3,375 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,543 N/A 2,543 2,797 3,052 3,306 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,733 N/A 3,733 4,106 4,480 4,853 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,733 N/A 3,733 4,106 4,480 4,853 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,371 N/A 2,371 2,608 2,845 3,082 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,733 N/A 3,733 4,106 4,480 4,853 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,683 N/A 3,683 4,051 4,420 4,788 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,371 N/A 2,371 2,608 2,845 3,082 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,371 N/A 2,371 2,608 2,845 3,082 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,371 N/A 2,371 2,608 2,845 3,082 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,733 N/A 3,733 4,106 4,480 4,853 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,733 N/A 3,733 4,106 4,480 4,853 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,371 N/A 2,371 2,608 2,845 3,082 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,173 N/A 2,173 2,390 2,608 2,825 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,173 N/A 2,173 2,390 2,608 2,825 7307 19 90 Cast tube or pipe fittings of steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 3,223 N/A 3,223 3,545 3,868 4,190 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3,223 N/A 3,223 3,545 3,868 4,190 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3,223 N/A 3,223 3,545 3,868 4,190 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3,223 N/A 3,223 3,545 3,868 4,190 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,413 N/A 3,413 3,754 4,096 4,437 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,663 N/A 3,663 4,029 4,396 4,762 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,543 N/A 2,543 2,797 3,052 3,306 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,543 N/A 3,543 3,897 4,252 4,606 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,563 N/A 3,563 3,919 4,276 4,632 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,563 N/A 3,563 3,919 4,276 4,632 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 3,153 N/A 3,153 3,468 3,784 4,099 (C) 7318 16 Nuts of iron or steel 3,443 N/A 3,443 3,787 4,132 4,476 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,633 N/A 2,633 2,896 3,160 3,423 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,563 N/A 2,563 2,819 3,076 3,332 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 30 Ladders and steps, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,423 N/A 2,423 2,665 2,908 3,150 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,543 N/A 2,543 2,797 3,052 3,306 (C) United Arab Emirates Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker 1,290 0,050 1,340 1,474 1,608 1,742 (B) 2523 10 00 Grey clinker 0,830 0,040 0,860 0,946 1,032 1,118 (A) 2523 21 00 White Portland cement 1,300 0,140 1,440 1,584 1,728 1,872 2523 29 00 Grey Portland cement 0,840 0,070 0,900 0,990 1,080 1,170 2523 90 00 White hydraulic cements 1,330 0,170 1,510 1,661 1,812 1,963 (B) 2523 90 00 Grey hydraulic cements 0,800 0,070 0,870 0,957 1,044 1,131 (A) 2523 30 00 Aluminous cement - - - - - - Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,870 N/A 1,870 2,057 2,244 2,431 (K) 7603 Aluminium powders and flakes 1,980 N/A 1,980 2,178 2,376 2,574 (K) 7604 10 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7604 10 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7604 21 00 Hollow profiles 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7604 29 10 Bars and rods 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7604 29 90 Profiles 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7605 Aluminium wire 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7608 Aluminium tubes and pipes 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7610 90 90 Other 2,220 N/A 2,220 2,442 2,664 2,886 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,200 N/A 2,200 2,420 2,640 2,860 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,660 N/A 2,660 2,926 3,192 3,458 (K) 7616 99 10 Cast 1,980 N/A 1,980 2,178 2,376 2,574 (K) 7616 99 90 Other 2,660 N/A 2,660 2,926 3,192 3,458 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 United Kingdom Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 0,930 0,020 0,950 1,045 1,140 1,235 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 0,940 0,040 0,980 1,078 1,176 1,274 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 0,900 0,050 0,940 1,034 1,128 1,222 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 0,720 0,030 0,750 0,758 0,758 0,758 2814 10 00 Anhydrous ammonia 1,970 0,090 2,050 2,071 2,071 2,071 2814 20 00 Ammonia in aqueous solution 0,590 0,030 0,620 0,626 0,626 0,626 2834 21 00 Nitrate of potassium 0,830 0,040 0,870 0,879 0,879 0,879 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,400 0,020 0,420 0,424 0,424 0,424 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,650 0,020 0,680 0,687 0,687 0,687 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,190 0,070 1,260 1,273 1,273 1,273 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,160 0,060 1,230 1,242 1,242 1,242 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,550 0,050 0,590 0,596 0,596 0,596 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 0,720 0,050 0,780 0,788 0,788 0,788 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 0,640 0,040 0,680 0,687 0,687 0,687 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,060 1,050 1,061 1,061 1,061 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,060 0,900 0,909 0,909 0,909 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,840 0,060 0,900 0,909 0,909 0,909 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,130 0,040 1,170 1,182 1,182 1,182 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,830 0,060 0,880 0,889 0,889 0,889 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 0,820 0,050 0,870 0,879 0,879 0,879 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 0,980 0,060 1,040 1,050 1,050 1,050 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,450 0,050 0,500 0,505 0,505 0,505 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,450 0,060 0,510 0,515 0,515 0,515 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,310 0,040 0,350 0,354 0,354 0,354 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,460 0,040 0,490 0,495 0,495 0,495 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammoniumhydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,290 0,030 0,320 0,323 0,323 0,323 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 0,600 0,070 0,670 0,677 0,677 0,677 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,510 0,070 0,570 0,576 0,576 0,576 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,040 0,630 0,636 0,636 0,636 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,310 0,030 0,340 0,343 0,343 0,343 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,870 N/A 1,870 2,057 2,244 2,431 (K) 7603 Aluminium powders and flakes 1,930 N/A 1,930 2,123 2,316 2,509 (K) 7604 10 10 Bars and rods 2,150 N/A 2,150 2,365 2,580 2,795 (K) 7604 10 90 Profiles 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7604 21 00 Hollow profiles 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7604 29 10 Bars and rods 2,150 N/A 2,150 2,365 2,580 2,795 (K) 7604 29 90 Profiles 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7605 Aluminium wire 2,150 N/A 2,150 2,365 2,580 2,795 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7608 Aluminium tubes and pipes 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7610 90 Other 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7610 90 90 Other 2,170 N/A 2,170 2,387 2,604 2,821 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,150 N/A 2,150 2,365 2,580 2,795 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,610 N/A 2,610 2,871 3,132 3,393 (K) 7616 99 10 Cast 1,930 N/A 1,930 2,123 2,316 2,509 (K) 7616 99 90 Other 2,610 N/A 2,610 2,871 3,132 3,393 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,270 0,010 0,280 0,308 0,336 0,364 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,170 N/A 2,170 2,387 2,604 2,821 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,220 N/A 2,220 2,442 2,664 2,886 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,500 N/A 2,500 2,750 3 3,250 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,500 N/A 2,500 2,750 3 3,250 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,420 N/A 2,420 2,662 2,904 3,146 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,500 N/A 2,500 2,750 3 3,250 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,500 N/A 2,500 2,750 3 3,250 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,500 N/A 2,500 2,750 3 3,250 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,500 N/A 2,500 2,750 3 3,250 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,840 N/A 3,840 4,224 4,608 4,992 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,290 N/A 3,290 3,619 3,948 4,277 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,290 N/A 3,290 3,619 3,948 4,277 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,840 N/A 3,840 4,224 4,608 4,992 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,290 N/A 3,290 3,619 3,948 4,277 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,840 N/A 3,840 4,224 4,608 4,992 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,290 N/A 3,290 3,619 3,948 4,277 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,370 N/A 3,370 3,707 4,044 4,381 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,370 N/A 3,370 3,707 4,044 4,381 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,370 N/A 3,370 3,707 4,044 4,381 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,370 N/A 3,370 3,707 4,044 4,381 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,370 N/A 3,370 3,707 4,044 4,381 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,370 N/A 3,370 3,707 4,044 4,381 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below - - - 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,290 N/A 3,290 3,619 3,948 4,277 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,290 N/A 3,290 3,619 3,948 4,277 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,370 N/A 3,370 3,707 4,044 4,381 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,370 N/A 3,370 3,707 4,044 4,381 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,110 N/A 3,110 3,421 3,732 4,043 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,110 N/A 3,110 3,421 3,732 4,043 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,110 N/A 3,110 3,421 3,732 4,043 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,840 N/A 3,840 4,224 4,608 4,992 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,110 N/A 3,110 3,421 3,732 4,043 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,110 N/A 3,110 3,421 3,732 4,043 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 4,170 N/A 4,170 4,587 5,004 5,421 (F) 7224 90 02 Semi-finished products of tool steel 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 4,170 N/A 4,170 4,587 5,004 5,421 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 4,170 N/A 4,170 4,587 5,004 5,421 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,740 N/A 4,740 5,214 5,688 6,162 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,620 N/A 3,620 3,982 4,344 4,706 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,740 N/A 4,740 5,214 5,688 6,162 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,620 N/A 3,620 3,982 4,344 4,706 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,620 N/A 3,620 3,982 4,344 4,706 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,700 N/A 3,700 4,070 4,440 4,810 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,170 N/A 4,170 4,587 5,004 5,421 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 4,170 N/A 4,170 4,587 5,004 5,421 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,440 N/A 3,440 3,784 4,128 4,472 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,500 N/A 2,500 2,750 3 3,250 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,810 N/A 2,810 3,091 3,372 3,653 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,730 N/A 2,730 3,003 3,276 3,549 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,110 N/A 3,110 3,421 3,732 4,043 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,110 N/A 3,110 3,421 3,732 4,043 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,110 N/A 3,110 3,421 3,732 4,043 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,110 N/A 3,110 3,421 3,732 4,043 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,110 N/A 3,110 3,421 3,732 4,043 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,230 N/A 2,230 2,453 2,676 2,899 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,230 N/A 2,230 2,453 2,676 2,899 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below - - - 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,370 N/A 3,370 3,707 4,044 4,381 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,370 N/A 3,370 3,707 4,044 4,381 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,420 N/A 2,420 2,662 2,904 3,146 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,370 N/A 3,370 3,707 4,044 4,381 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,290 N/A 3,290 3,619 3,948 4,277 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,490 N/A 2,490 2,739 2,988 3,237 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,410 N/A 2,410 2,651 2,892 3,133 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,490 N/A 2,490 2,739 2,988 3,237 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,370 N/A 3,370 3,707 4,044 4,381 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,370 N/A 3,370 3,707 4,044 4,381 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,500 N/A 2,500 2,750 3 3,250 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,500 N/A 2,500 2,750 3 3,250 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,930 N/A 2,930 3,223 3,516 3,809 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,930 N/A 2,930 3,223 3,516 3,809 7307 19 90 Cast tube or pipe fittings of steel 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,780 N/A 2,780 3,058 3,336 3,614 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,780 N/A 2,780 3,058 3,336 3,614 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,780 N/A 2,780 3,058 3,336 3,614 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,780 N/A 2,780 3,058 3,336 3,614 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,210 N/A 3,210 3,531 3,852 4,173 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,500 N/A 2,500 2,750 3 3,250 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,030 N/A 3,030 3,333 3,636 3,939 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,110 N/A 3,110 3,421 3,732 4,043 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,110 N/A 3,110 3,421 3,732 4,043 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7318 16 Nuts of iron or steel 2,980 N/A 2,980 3,278 3,576 3,874 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,320 N/A 2,320 2,552 2,784 3,016 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 30 Ladders and steps, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,310 N/A 2,310 2,541 2,772 3,003 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 3,040 N/A 3,040 3,344 3,648 3,952 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,500 N/A 2,500 2,750 3 3,250 (C) United States Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,220 0,090 0,310 0,341 0,372 0,403 (A) 2523 10 00 White clinker 1,320 0,050 1,370 1,507 1,644 1,781 (B) 2523 10 00 Grey clinker 1,160 0,030 1,190 1,309 1,428 1,547 (A) 2523 21 00 White Portland cement 1,240 0,140 1,380 1,518 1,656 1,794 2523 29 00 Grey Portland cement 1,160 0,060 1,210 1,331 1,452 1,573 2523 90 00 White hydraulic cements 1,290 0,160 1,450 1,595 1,740 1,885 (B) 2523 90 00 Grey hydraulic cements 1,100 0,060 1,160 1,276 1,392 1,508 (A) 2523 30 00 Aluminous cement 1,800 0,140 1,940 2,134 2,328 2,522 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,870 0,030 1,900 1,919 1,919 1,919 2814 10 00 Anhydrous ammonia 3,320 0,090 3,410 3,444 3,444 3,444 2814 20 00 Ammonia in aqueous solution 1 0,030 1,020 1,030 1,030 1,030 2834 21 00 Nitrate of potassium 1,860 0,040 1,910 1,929 1,929 1,929 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,020 0,760 0,768 0,768 0,768 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,220 0,020 1,240 1,252 1,252 1,252 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,220 0,070 2,290 2,313 2,313 2,313 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2,170 0,070 2,240 2,262 2,262 2,262 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,970 0,060 1,030 1,040 1,040 1,040 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,460 0,060 1,530 1,545 1,545 1,545 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,430 0,050 1,470 1,485 1,485 1,485 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,190 0,070 2,270 2,293 2,293 2,293 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,910 0,070 1,980 2 2 2 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,910 0,070 1,980 2 2 2 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,920 0,050 2,970 3 3 3 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,840 0,060 1,910 1,929 1,929 1,929 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,680 0,060 1,740 1,757 1,757 1,757 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,950 0,070 2,020 2,040 2,040 2,040 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,900 0,060 0,960 0,970 0,970 0,970 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1 0,070 1,060 1,071 1,071 1,071 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,680 0,050 0,740 0,747 0,747 0,747 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,780 0,040 0,820 0,828 0,828 0,828 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,500 0,030 0,530 0,535 0,535 0,535 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,340 0,090 1,420 1,434 1,434 1,434 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,900 0,100 1,010 1,020 1,020 1,020 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,280 0,050 1,340 1,353 1,353 1,353 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,670 0,040 0,710 0,717 0,717 0,717 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 2,032 N/A 2,032 2,235 2,439 2,642 (K) 7604 10 10 Bars and rods 2,258 N/A 2,258 2,484 2,709 2,935 (K) 7604 10 90 Profiles 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7604 21 00 Hollow profiles 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7604 29 10 Bars and rods 2,258 N/A 2,258 2,484 2,709 2,935 (K) 7604 29 90 Profiles 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7605 Aluminium wire 2,258 N/A 2,258 2,484 2,709 2,935 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7608 Aluminium tubes and pipes 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7610 90 Other 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7610 90 90 Other 2,278 N/A 2,278 2,506 2,734 2,962 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,258 N/A 2,258 2,484 2,709 2,935 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,730 N/A 2,730 3,003 3,276 3,549 (K) 7616 99 10 Cast 2,032 N/A 2,032 2,235 2,439 2,642 (K) 7616 99 90 Other 2,730 N/A 2,730 3,003 3,276 3,549 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 26,640 N/A 26,640 29,304 31,968 34,632 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,660 0,020 0,680 0,748 0,816 0,884 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 1,210 N/A 1,210 1,331 1,452 1,573 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 0,450 N/A 0,450 0,495 0,540 0,585 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,425 N/A 2,425 2,667 2,910 3,152 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 1,400 N/A 1,400 1,540 1,680 1,820 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 1,400 N/A 1,400 1,540 1,680 1,820 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 1,400 N/A 1,400 1,540 1,680 1,820 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 1,400 N/A 1,400 1,540 1,680 1,820 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below - - - 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,110 N/A 3,110 3,421 3,732 4,043 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,220 N/A 3,220 3,542 3,864 4,186 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,220 N/A 3,220 3,542 3,864 4,186 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,110 N/A 3,110 3,421 3,732 4,043 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,220 N/A 3,220 3,542 3,864 4,186 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,110 N/A 3,110 3,421 3,732 4,043 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,220 N/A 3,220 3,542 3,864 4,186 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,270 N/A 3,270 3,597 3,924 4,251 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,270 N/A 3,270 3,597 3,924 4,251 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,270 N/A 3,270 3,597 3,924 4,251 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,270 N/A 3,270 3,597 3,924 4,251 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,270 N/A 3,270 3,597 3,924 4,251 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,270 N/A 3,270 3,597 3,924 4,251 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,220 N/A 3,220 3,542 3,864 4,186 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,220 N/A 3,220 3,542 3,864 4,186 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,270 N/A 3,270 3,597 3,924 4,251 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,270 N/A 3,270 3,597 3,924 4,251 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,270 N/A 3,270 3,597 3,924 4,251 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,270 N/A 3,270 3,597 3,924 4,251 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,270 N/A 3,270 3,597 3,924 4,251 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,270 N/A 3,270 3,597 3,924 4,251 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,110 N/A 3,110 3,421 3,732 4,043 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,270 N/A 3,270 3,597 3,924 4,251 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,270 N/A 3,270 3,597 3,924 4,251 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,490 N/A 3,490 3,839 4,188 4,537 (F) 7224 90 02 Semi-finished products of tool steel 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,490 N/A 3,490 3,839 4,188 4,537 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,490 N/A 3,490 3,839 4,188 4,537 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,730 N/A 4,730 5,203 5,676 6,149 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,730 N/A 4,730 5,203 5,676 6,149 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,590 N/A 3,590 3,949 4,308 4,667 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,590 N/A 3,590 3,949 4,308 4,667 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,640 N/A 3,640 4,004 4,368 4,732 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,490 N/A 3,490 3,839 4,188 4,537 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,640 N/A 3,640 4,004 4,368 4,732 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,490 N/A 3,490 3,839 4,188 4,537 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,640 N/A 3,640 4,004 4,368 4,732 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,640 N/A 3,640 4,004 4,368 4,732 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,640 N/A 3,640 4,004 4,368 4,732 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,740 N/A 2,740 3,014 3,288 3,562 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 1,850 N/A 1,850 2,035 2,220 2,405 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,190 N/A 3,190 3,509 3,828 4,147 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 1,974 N/A 1,974 2,171 2,369 2,566 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,190 N/A 3,190 3,509 3,828 4,147 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 1,974 N/A 1,974 2,171 2,369 2,566 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,190 N/A 3,190 3,509 3,828 4,147 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 1,974 N/A 1,974 2,171 2,369 2,566 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 1,974 N/A 1,974 2,171 2,369 2,566 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 1,974 N/A 1,974 2,171 2,369 2,566 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,190 N/A 3,190 3,509 3,828 4,147 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,190 N/A 3,190 3,509 3,828 4,147 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,974 N/A 1,974 2,171 2,369 2,566 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 1,974 N/A 1,974 2,171 2,369 2,566 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 1,974 N/A 1,974 2,171 2,369 2,566 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,270 N/A 3,270 3,597 3,924 4,251 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,270 N/A 3,270 3,597 3,924 4,251 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 1,400 N/A 1,400 1,540 1,680 1,820 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,270 N/A 3,270 3,597 3,924 4,251 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,220 N/A 3,220 3,542 3,864 4,186 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 1,480 N/A 1,480 1,628 1,776 1,924 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 1,430 N/A 1,430 1,573 1,716 1,859 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 1,480 N/A 1,480 1,628 1,776 1,924 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,270 N/A 3,270 3,597 3,924 4,251 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,270 N/A 3,270 3,597 3,924 4,251 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 1,260 N/A 1,260 1,386 1,512 1,638 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 1,260 N/A 1,260 1,386 1,512 1,638 7307 19 90 Cast tube or pipe fittings of steel 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,800 N/A 2,800 3,080 3,360 3,640 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,800 N/A 2,800 3,080 3,360 3,640 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,800 N/A 2,800 3,080 3,360 3,640 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,800 N/A 2,800 3,080 3,360 3,640 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 1,410 N/A 1,410 1,551 1,692 1,833 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 1,410 N/A 1,410 1,551 1,692 1,833 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 1,410 N/A 1,410 1,551 1,692 1,833 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 1,410 N/A 1,410 1,551 1,692 1,833 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,900 N/A 2,900 3,190 3,480 3,770 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,190 N/A 3,190 3,509 3,828 4,147 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 1,440 N/A 1,440 1,584 1,728 1,872 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,730 N/A 3,730 4,103 4,476 4,849 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,170 N/A 3,170 3,487 3,804 4,121 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,170 N/A 3,170 3,487 3,804 4,121 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,580 N/A 2,580 2,838 3,096 3,354 (C) 7318 16 Nuts of iron or steel 3,030 N/A 3,030 3,333 3,636 3,939 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 1,830 N/A 1,830 2,013 2,196 2,379 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 1,680 N/A 1,680 1,848 2,016 2,184 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7318 29 00 Non-threaded articles, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7326 90 30 Ladders and steps, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 1,390 N/A 1,390 1,529 1,668 1,807 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 1,330 N/A 1,330 1,463 1,596 1,729 (C) 7326 90 98 Articles of iron or steel, n.e.s. 1,440 N/A 1,440 1,584 1,728 1,872 (C) Uruguay Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - 2523 10 00 White clinker - - - 2523 10 00 Grey clinker 1,090 0,010 1,100 1,210 1,320 1,430 (A) 2523 21 00 White Portland cement - - - 2523 29 00 Grey Portland cement 1,090 0,020 1,110 1,221 1,332 1,443 2523 90 00 White hydraulic cements - - - 2523 90 00 Grey hydraulic cements 1,040 0,030 1,060 1,166 1,272 1,378 (A) 2523 30 00 Aluminous cement - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,020 1,820 1,838 1,838 1,838 2814 10 00 Anhydrous ammonia - - - 2814 20 00 Ammonia in aqueous solution 0,680 0,020 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 1,610 0,040 1,650 1,667 1,667 1,667 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,500 0,020 0,530 0,535 0,535 0,535 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,830 0,020 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,520 0,060 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,480 0,060 1,550 1,566 1,566 1,566 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,050 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,150 0,060 1,210 1,222 1,222 1,222 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,040 1,270 1,283 1,283 1,283 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,060 1,950 1,970 1,970 1,970 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,060 1,690 1,707 1,707 1,707 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,060 1,690 1,707 1,707 1,707 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,810 0,040 2,850 2,879 2,879 2,879 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,580 0,060 1,640 1,656 1,656 1,656 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,320 0,050 1,380 1,394 1,394 1,394 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,460 0,060 1,520 1,535 1,535 1,535 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,050 0,740 0,747 0,747 0,747 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,060 0,880 0,889 0,889 0,889 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,050 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,040 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,030 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,120 0,080 1,200 1,212 1,212 1,212 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,080 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,050 1,130 1,141 1,141 1,141 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,030 0,590 0,596 0,596 0,596 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 2,420 N/A 2,420 2,662 2,904 3,146 (L) 7604 10 10 Bars and rods 2,640 N/A 2,640 2,904 3,168 3,432 (L) 7604 10 90 Profiles 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7604 21 00 Hollow profiles 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7604 29 10 Bars and rods 2,640 N/A 2,640 2,904 3,168 3,432 (L) 7604 29 90 Profiles 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7605 Aluminium wire 2,640 N/A 2,640 2,904 3,168 3,432 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7608 Aluminium tubes and pipes 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7610 90 Other 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7610 90 90 Other 2,660 N/A 2,660 2,926 3,192 3,458 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,640 N/A 2,640 2,904 3,168 3,432 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 3,100 N/A 3,100 3,410 3,720 4,030 (L) 7616 99 10 Cast 2,420 N/A 2,420 2,662 2,904 3,146 (L) 7616 99 90 Other 3,100 N/A 3,100 3,410 3,720 4,030 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Uzbekistan Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,360 0,030 1,390 1,529 1,668 1,807 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,360 0,060 1,410 1,551 1,692 1,833 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,290 0,060 1,350 1,485 1,620 1,755 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,730 0,040 2,770 2,798 2,798 2,798 2814 10 00 Anhydrous ammonia 2,160 0,140 2,300 2,323 2,323 2,323 2814 20 00 Ammonia in aqueous solution 0,650 0,040 0,690 0,697 0,697 0,697 2834 21 00 Nitrate of potassium 2,210 0,060 2,270 2,293 2,293 2,293 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,490 0,040 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,810 0,040 0,840 0,848 0,848 0,848 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,470 0,100 1,570 1,586 1,586 1,586 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,440 0,100 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,640 0,080 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,420 0,090 1,500 1,515 1,515 1,515 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,670 0,070 1,740 1,757 1,757 1,757 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,570 0,100 2,670 2,697 2,697 2,697 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,200 0,090 2,300 2,323 2,323 2,323 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,200 0,090 2,300 2,323 2,323 2,323 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,260 0,070 4,330 4,373 4,373 4,373 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,150 0,090 2,240 2,262 2,262 2,262 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,610 0,080 1,700 1,717 1,717 1,717 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,660 0,100 1,750 1,768 1,768 1,768 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,820 0,080 0,890 0,899 0,899 0,899 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,080 0,090 1,170 1,182 1,182 1,182 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,730 0,070 0,800 0,808 0,808 0,808 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,060 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,050 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,480 0,120 1,600 1,616 1,616 1,616 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,590 0,100 0,690 0,697 0,697 0,697 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,450 0,070 1,520 1,535 1,535 1,535 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,740 0,050 0,790 0,798 0,798 0,798 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,060 N/A 1,060 1,166 1,272 1,378 (L) 7604 10 10 Bars and rods 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 10 90 Profiles 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7604 21 00 Hollow profiles 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7604 29 10 Bars and rods 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7604 29 90 Profiles 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7605 Aluminium wire 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7608 Aluminium tubes and pipes 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7610 90 Other 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7610 90 90 Other 1,300 N/A 1,300 1,430 1,560 1,690 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 1,290 N/A 1,290 1,419 1,548 1,677 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,740 N/A 1,740 1,914 2,088 2,262 (L) 7616 99 10 Cast 1,060 N/A 1,060 1,166 1,272 1,378 (L) 7616 99 90 Other 1,740 N/A 1,740 1,914 2,088 2,262 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,390 0,350 0,740 0,814 0,888 0,962 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms - N/A - - - - 7202 11 Ferro-manganese, containing by weight > 2% of carbon - N/A - - - - 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - - - - 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - - - - 7202 60 00 Ferro-nickel - N/A - - - - 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - - - - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 3,670 N/A 3,670 4,037 4,404 4,771 (E) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below N/A see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,050 N/A 3,050 3,355 3,660 3,965 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 3,120 N/A 3,120 3,432 3,744 4,056 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 3,120 N/A 3,120 3,432 3,744 4,056 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 3,050 N/A 3,050 3,355 3,660 3,965 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 3,120 N/A 3,120 3,432 3,744 4,056 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 3,050 N/A 3,050 3,355 3,660 3,965 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 3,120 N/A 3,120 3,432 3,744 4,056 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,120 N/A 3,120 3,432 3,744 4,056 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 3,120 N/A 3,120 3,432 3,744 4,056 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 3,120 N/A 3,120 3,432 3,744 4,056 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 3,120 N/A 3,120 3,432 3,744 4,056 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 3,120 N/A 3,120 3,432 3,744 4,056 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 3,120 N/A 3,120 3,432 3,744 4,056 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below N/A see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 3,120 N/A 3,120 3,432 3,744 4,056 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 3,120 N/A 3,120 3,432 3,744 4,056 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 3,120 N/A 3,120 3,432 3,744 4,056 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 3,050 N/A 3,050 3,355 3,660 3,965 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 3,120 N/A 3,120 3,432 3,744 4,056 7223 Wire of stainless steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 3,120 N/A 3,120 3,432 3,744 4,056 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,190 N/A 3,190 3,509 3,828 4,147 (H) 7224 90 02 Semi-finished products of tool steel 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,190 N/A 3,190 3,509 3,828 4,147 (H) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,190 N/A 3,190 3,509 3,828 4,147 (H) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,930 N/A 4,930 5,423 5,916 6,409 (E) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,260 N/A 3,260 3,586 3,912 4,238 (E) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,930 N/A 4,930 5,423 5,916 6,409 (E) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,260 N/A 3,260 3,586 3,912 4,238 (E) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,260 N/A 3,260 3,586 3,912 4,238 (E)/(H) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,190 N/A 3,190 3,509 3,828 4,147 (H) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,260 N/A 3,260 3,586 3,912 4,238 (E)/(H) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,190 N/A 3,190 3,509 3,828 4,147 (H) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,260 N/A 3,260 3,586 3,912 4,238 (E)/(H) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,260 N/A 3,260 3,586 3,912 4,238 (H) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,260 N/A 3,260 3,586 3,912 4,238 (E)/(H) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 3,730 N/A 3,730 4,103 4,476 4,849 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,120 N/A 3,120 3,432 3,744 4,056 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,120 N/A 3,120 3,432 3,744 4,056 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,120 N/A 3,120 3,432 3,744 4,056 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,120 N/A 3,120 3,432 3,744 4,056 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,120 N/A 3,120 3,432 3,744 4,056 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,200 N/A 3,200 3,520 3,840 4,160 (H) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,200 N/A 3,200 3,520 3,840 4,160 (E)/(H) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 3,200 N/A 3,200 3,520 3,840 4,160 (E) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,120 N/A 3,120 3,432 3,744 4,056 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,120 N/A 3,120 3,432 3,744 4,056 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 3,210 N/A 3,210 3,531 3,852 4,173 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,120 N/A 3,120 3,432 3,744 4,056 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,120 N/A 3,120 3,432 3,744 4,056 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 3,210 N/A 3,210 3,531 3,852 4,173 (H) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 3,210 N/A 3,210 3,531 3,852 4,173 (H) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 3,210 N/A 3,210 3,531 3,852 4,173 (H) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,120 N/A 3,120 3,432 3,744 4,056 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,120 N/A 3,120 3,432 3,744 4,056 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,670 N/A 3,670 4,037 4,404 4,771 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,670 N/A 3,670 4,037 4,404 4,771 7307 19 90 Cast tube or pipe fittings of steel 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7307 21 00 Flanges of stainless steel (excl. cast products) 3,210 N/A 3,210 3,531 3,852 4,173 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 3,210 N/A 3,210 3,531 3,852 4,173 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 3,210 N/A 3,210 3,531 3,852 4,173 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 3,210 N/A 3,210 3,531 3,852 4,173 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 3,010 N/A 3,010 3,311 3,612 3,913 (E) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,120 N/A 3,120 3,432 3,744 4,056 (E) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 13 00 Screw hooks and screw rings, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,120 N/A 3,120 3,432 3,744 4,056 (E) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 16 Nuts of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 21 00 Spring washers and other lock washers, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 24 00 Cotters and cotter pins, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7318 29 00 Non-threaded articles, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7326 20 00 Articles of iron or steel wire, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7326 90 30 Ladders and steps, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7326 90 50 Reels for cables, piping and the like, of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 3,210 N/A 3,210 3,531 3,852 4,173 (E) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7326 90 96 Sintered articles of iron or steel, n.e.s. 3,150 N/A 3,150 3,465 3,780 4,095 (E) 7326 90 98 Articles of iron or steel, n.e.s. 3,210 N/A 3,210 3,531 3,852 4,173 (E) Venezuela Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - 2523 10 00 White clinker 1,320 0,030 1,340 1,474 1,608 1,742 (B) 2523 10 00 Grey clinker 1,080 0,020 1,100 1,210 1,320 1,430 (A) 2523 21 00 White Portland cement 1,240 0,120 1,360 1,496 1,632 1,768 2523 29 00 Grey Portland cement 1,080 0,030 1,110 1,221 1,332 1,443 2523 90 00 White hydraulic cements 1,280 0,140 1,420 1,562 1,704 1,846 (B) 2523 90 00 Grey hydraulic cements 1,030 0,040 1,060 1,166 1,272 1,378 (A) 2523 30 00 Aluminous cement - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,800 0,020 1,830 1,848 1,848 1,848 2814 10 00 Anhydrous ammonia 2,260 0,070 2,330 2,353 2,353 2,353 2814 20 00 Ammonia in aqueous solution 0,680 0,020 0,700 0,707 0,707 0,707 2834 21 00 Nitrate of potassium 1,620 0,040 1,650 1,667 1,667 1,667 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,500 0,020 0,520 0,525 0,525 0,525 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,840 0,020 0,860 0,869 0,869 0,869 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,520 0,060 1,580 1,596 1,596 1,596 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,490 0,060 1,540 1,555 1,555 1,555 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,660 0,050 0,710 0,717 0,717 0,717 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,160 0,050 1,210 1,222 1,222 1,222 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,230 0,040 1,270 1,283 1,283 1,283 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,890 0,060 1,950 1,970 1,970 1,970 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,060 1,690 1,707 1,707 1,707 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,630 0,060 1,690 1,707 1,707 1,707 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,820 0,040 2,850 2,879 2,879 2,879 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,580 0,050 1,640 1,656 1,656 1,656 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,330 0,050 1,370 1,384 1,384 1,384 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,460 0,060 1,520 1,535 1,535 1,535 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,690 0,050 0,740 0,747 0,747 0,747 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,820 0,060 0,880 0,889 0,889 0,889 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,560 0,050 0,610 0,616 0,616 0,616 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,530 0,040 0,570 0,576 0,576 0,576 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,340 0,030 0,370 0,374 0,374 0,374 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,120 0,070 1,200 1,212 1,212 1,212 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,610 0,070 0,680 0,687 0,687 0,687 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,090 0,040 1,130 1,141 1,141 1,141 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,560 0,030 0,590 0,596 0,596 0,596 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 1,700 N/A 1,700 1,870 2,040 2,210 (K) 7603 Aluminium powders and flakes 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7604 10 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 10 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 21 00 Hollow profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7604 29 10 Bars and rods 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7604 29 90 Profiles 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7605 Aluminium wire 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7608 Aluminium tubes and pipes 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7610 90 90 Other 2,050 N/A 2,050 2,255 2,460 2,665 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,040 N/A 2,040 2,244 2,448 2,652 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,490 N/A 2,490 2,739 2,988 3,237 (K) 7616 99 10 Cast 1,810 N/A 1,810 1,991 2,172 2,353 (K) 7616 99 90 Other 2,490 N/A 2,490 2,739 2,988 3,237 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon _ _ _ _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon _ _ _ _ _ _ 7202 49 Ferro-chromium, containing by weight <= 4% of carbon _ _ _ _ _ _ 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 Vietnam Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,410 0,050 2,460 2,485 2,485 2,485 2814 10 00 Anhydrous ammonia 3,460 0,150 3,610 3,646 3,646 3,646 2814 20 00 Ammonia in aqueous solution 1,040 0,050 1,080 1,091 1,091 1,091 2834 21 00 Nitrate of potassium 2,240 0,070 2,310 2,333 2,333 2,333 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,770 0,040 0,810 0,818 0,818 0,818 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,270 0,040 1,310 1,323 1,323 1,323 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,310 0,120 2,430 2,454 2,454 2,454 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2,260 0,120 2,380 2,404 2,404 2,404 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,010 0,090 1,100 1,111 1,111 1,111 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,660 0,100 1,760 1,778 1,778 1,778 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,710 0,080 1,780 1,798 1,798 1,798 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,630 0,120 2,750 2,778 2,778 2,778 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,280 0,110 2,380 2,404 2,404 2,404 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,280 0,110 2,380 2,404 2,404 2,404 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 3,760 0,080 3,840 3,878 3,878 3,878 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,210 0,100 2,310 2,333 2,333 2,333 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,900 0,090 2 2,020 2,020 2,020 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 2,140 0,110 2,260 2,283 2,283 2,283 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 1 0,090 1,090 1,101 1,101 1,101 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,160 0,110 1,270 1,283 1,283 1,283 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,790 0,080 0,880 0,889 0,889 0,889 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,810 0,070 0,880 0,889 0,889 0,889 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,050 0,570 0,576 0,576 0,576 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,570 0,140 1,710 1,727 1,727 1,727 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,930 0,130 1,060 1,071 1,071 1,071 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,520 0,080 1,600 1,616 1,616 1,616 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,790 0,060 0,850 0,859 0,859 0,859 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 1,800 N/A 1,800 1,980 2,160 2,340 (L) 7604 10 10 Bars and rods 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7604 10 90 Profiles 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7604 21 00 Hollow profiles 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7604 29 10 Bars and rods 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7604 29 90 Profiles 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7605 Aluminium wire 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7608 Aluminium tubes and pipes 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7610 90 Other 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7610 90 90 Other 2,040 N/A 2,040 2,244 2,448 2,652 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 2,020 N/A 2,020 2,222 2,424 2,626 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 2,480 N/A 2,480 2,728 2,976 3,224 (L) 7616 99 10 Cast 1,800 N/A 1,800 1,980 2,160 2,340 (L) 7616 99 90 Other 2,480 N/A 2,480 2,728 2,976 3,224 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 1,040 0,070 1,110 1,221 1,332 1,443 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 2,190 N/A 2,190 2,409 2,628 2,847 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon - N/A - _ _ _ 7202 41 Ferro-chromium, containing by weight > 4% of carbon - N/A - _ _ - 7202 49 Ferro-chromium, containing by weight <= 4% of carbon - N/A - _ _ - 7202 60 00 Ferro-nickel 3,480 N/A 3,480 3,828 4,176 4,524 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms - N/A - _ _ - 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 2,240 N/A 2,240 2,464 2,688 2,912 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below N/A see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 Semi-finished products of iron or non-alloy steel see below N/A see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below N/A see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below N/A see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below N/A see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) - - - - - - 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section - - - - - - 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting - - - - - - 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged - - - - - - 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting - - - - - - 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) - - - - - - 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm - - - - - - 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm - - - - - - 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm - - - - - - 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm - - - - - - 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm - - - - - - 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm - - - - - - 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm - - - - - - 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm - - - - - - 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm - - - - - - 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm - - - - - - 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm - - - - - - 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm - - - - - - 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm - - - - - - 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked - - - - - - 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm - - - - - - 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm - - - - - - 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" - - - - - - 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked - - - - - - 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils - - - - - - 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section - - - - - - 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) - - - - - - 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished - - - - - - 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. - - - - - - 7222 40 Angles, shapes and sections of stainless steel, n.e.s. - - - - - - 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) - - - - - - 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below N/A see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7224 90 02 Semi-finished products of tool steel 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 4,600 N/A 4,600 5,060 5,520 5,980 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 3,480 N/A 3,480 3,828 4,176 4,524 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below N/A see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 4,600 N/A 4,600 5,060 5,520 5,980 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 3,480 N/A 3,480 3,828 4,176 4,524 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 3,480 N/A 3,480 3,828 4,176 4,524 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below N/A see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,440 N/A 3,440 3,784 4,128 4,472 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 3,500 N/A 3,500 3,850 4,200 4,550 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 3,500 N/A 3,500 3,850 4,200 4,550 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 2,770 N/A 2,770 3,047 3,324 3,601 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below N/A see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 2,230 N/A 2,230 2,453 2,676 2,899 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below N/A see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 3,070 N/A 3,070 3,377 3,684 3,991 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 3,070 N/A 3,070 3,377 3,684 3,991 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 3,070 N/A 3,070 3,377 3,684 3,991 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,070 N/A 3,070 3,377 3,684 3,991 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 3,070 N/A 3,070 3,377 3,684 3,991 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,260 N/A 2,260 2,486 2,712 2,938 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 2,260 N/A 2,260 2,486 2,712 2,938 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below N/A see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,120 N/A 3,120 3,432 3,744 4,056 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 3,120 N/A 3,120 3,432 3,744 4,056 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 2,350 N/A 2,350 2,585 2,820 3,055 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,120 N/A 3,120 3,432 3,744 4,056 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 3,110 N/A 3,110 3,421 3,732 4,043 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 2,320 N/A 2,320 2,552 2,784 3,016 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 2,310 N/A 2,310 2,541 2,772 3,003 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 2,320 N/A 2,320 2,552 2,784 3,016 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 3,120 N/A 3,120 3,432 3,744 4,056 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 3,120 N/A 3,120 3,432 3,744 4,056 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below N/A see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 2,230 N/A 2,230 2,453 2,676 2,899 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 2,230 N/A 2,230 2,453 2,676 2,899 7307 19 90 Cast tube or pipe fittings of steel 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 2,740 N/A 2,740 3,014 3,288 3,562 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 2,740 N/A 2,740 3,014 3,288 3,562 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 2,740 N/A 2,740 3,014 3,288 3,562 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 2,740 N/A 2,740 3,014 3,288 3,562 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 2,840 N/A 2,840 3,124 3,408 3,692 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 2,990 N/A 2,990 3,289 3,588 3,887 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 2,370 N/A 2,370 2,607 2,844 3,081 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below N/A see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 2,960 N/A 2,960 3,256 3,552 3,848 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below N/A see below see below see below see below 7318 11 00 Coach screws of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 3,090 N/A 3,090 3,399 3,708 4,017 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 3,090 N/A 3,090 3,399 3,708 4,017 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 2,750 N/A 2,750 3,025 3,300 3,575 (C) 7318 16 Nuts of iron or steel 2,960 N/A 2,960 3,256 3,552 3,848 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 2,410 N/A 2,410 2,651 2,892 3,133 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7318 29 00 Non-threaded articles, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below N/A see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7326 90 30 Ladders and steps, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 2,350 N/A 2,350 2,585 2,820 3,055 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 2,330 N/A 2,330 2,563 2,796 3,029 (C) 7326 90 98 Articles of iron or steel, n.e.s. 2,370 N/A 2,370 2,607 2,844 3,081 (C) Yemen Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - (A) 2523 10 00 White clinker - - - - - - (B) 2523 10 00 Grey clinker 1,280 0,050 1,330 1,463 1,596 1,729 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,240 0,090 1,330 1,463 1,596 1,729 2523 90 00 White hydraulic cements - - - - - - (B) 2523 90 00 Grey hydraulic cements 1,180 0,090 1,270 1,397 1,524 1,651 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,670 0,050 2,720 2,747 2,747 2,747 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,710 0,050 0,760 0,768 0,768 0,768 2834 21 00 Nitrate of potassium 2,170 0,060 2,240 2,262 2,262 2,262 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,030 0,480 0,485 0,485 0,485 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,740 0,030 0,770 0,778 0,778 0,778 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,350 0,090 1,440 1,454 1,454 1,454 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,320 0,090 1,410 1,424 1,424 1,424 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,610 0,040 0,660 0,667 0,667 0,667 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,370 0,050 1,430 1,444 1,444 1,444 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,620 0,050 1,670 1,687 1,687 1,687 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,500 0,070 2,570 2,596 2,596 2,596 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,090 0,060 2,150 2,172 2,172 2,172 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,090 0,060 2,150 2,172 2,172 2,172 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,170 0,080 4,250 4,293 4,293 4,293 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,090 0,060 2,150 2,172 2,172 2,172 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,560 0,060 1,620 1,636 1,636 1,636 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,560 0,080 1,630 1,646 1,646 1,646 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,780 0,030 0,810 0,818 0,818 0,818 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,010 0,030 1,040 1,050 1,050 1,050 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,670 0,020 0,690 0,697 0,697 0,697 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,040 0,560 0,566 0,566 0,566 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,320 0,020 0,340 0,343 0,343 0,343 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,400 0,040 1,440 1,454 1,454 1,454 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,540 0,040 0,580 0,586 0,586 0,586 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,400 0,040 1,440 1,454 1,454 1,454 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,700 0,020 0,720 0,727 0,727 0,727 Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Zambia Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,640 0,070 1,710 1,727 1,727 1,727 2814 10 00 Anhydrous ammonia - - - - - - 2814 20 00 Ammonia in aqueous solution 0,610 0,070 0,680 0,687 0,687 0,687 2834 21 00 Nitrate of potassium 1,460 0,090 1,560 1,576 1,576 1,576 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,450 0,050 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,750 0,050 0,800 0,808 0,808 0,808 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,360 0,150 1,510 1,525 1,525 1,525 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,330 0,150 1,480 1,495 1,495 1,495 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,590 0,090 0,680 0,687 0,687 0,687 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,040 0,100 1,150 1,162 1,162 1,162 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,110 0,080 1,200 1,212 1,212 1,212 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,710 0,130 1,840 1,858 1,858 1,858 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,480 0,110 1,590 1,606 1,606 1,606 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,480 0,110 1,590 1,606 1,606 1,606 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,560 0,110 2,660 2,687 2,687 2,687 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,440 0,110 1,550 1,566 1,566 1,566 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,200 0,110 1,300 1,313 1,313 1,313 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,320 0,130 1,440 1,454 1,454 1,454 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,620 0,080 0,700 0,707 0,707 0,707 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,750 0,090 0,840 0,848 0,848 0,848 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,510 0,070 0,580 0,586 0,586 0,586 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,070 0,550 0,556 0,556 0,556 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,050 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,010 0,120 1,130 1,141 1,141 1,141 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,110 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,980 0,080 1,070 1,081 1,081 1,081 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,510 0,050 0,560 0,566 0,566 0,566 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,590 N/A 0,590 0,649 0,708 0,767 (L) 7604 10 10 Bars and rods 0,810 N/A 0,810 0,891 0,972 1,053 (L) 7604 10 90 Profiles 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7604 21 00 Hollow profiles 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7604 29 10 Bars and rods 0,810 N/A 0,810 0,891 0,972 1,053 (L) 7604 29 90 Profiles 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7605 Aluminium wire 0,810 N/A 0,810 0,891 0,972 1,053 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7608 Aluminium tubes and pipes 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7610 90 Other 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7610 90 90 Other 0,830 N/A 0,830 0,913 0,996 1,079 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,810 N/A 0,810 0,891 0,972 1,053 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,270 N/A 1,270 1,397 1,524 1,651 (L) 7616 99 10 Cast 0,590 N/A 0,590 0,649 0,708 0,767 (L) 7616 99 90 Other 1,270 N/A 1,270 1,397 1,524 1,651 (L) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 10,820 N/A 10,820 11,902 12,984 14,066 Zimbabwe Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay - - - - - - 2523 10 00 White clinker - - - - - - 2523 10 00 Grey clinker 1,240 0,040 1,290 1,419 1,548 1,677 (A) 2523 21 00 White Portland cement - - - - - - 2523 29 00 Grey Portland cement 1,240 0,070 1,310 1,441 1,572 1,703 2523 90 00 White hydraulic cements - - - - - - 2523 90 00 Grey hydraulic cements 1,180 0,080 1,250 1,375 1,500 1,625 (A) 2523 30 00 Aluminous cement - - - - - - Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 1,650 0,050 1,710 1,727 1,727 1,727 2814 10 00 Anhydrous ammonia 2,020 0,160 2,180 2,202 2,202 2,202 2814 20 00 Ammonia in aqueous solution 0,600 0,050 0,660 0,667 0,667 0,667 2834 21 00 Nitrate of potassium 1,470 0,080 1,550 1,566 1,566 1,566 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,460 0,040 0,500 0,505 0,505 0,505 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,760 0,040 0,800 0,808 0,808 0,808 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 1,390 0,120 1,510 1,525 1,525 1,525 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 1,360 0,120 1,480 1,495 1,495 1,495 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,600 0,090 0,690 0,697 0,697 0,697 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,050 0,100 1,150 1,162 1,162 1,162 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,120 0,080 1,200 1,212 1,212 1,212 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,730 0,120 1,850 1,869 1,869 1,869 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,500 0,110 1,610 1,626 1,626 1,626 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,500 0,110 1,610 1,626 1,626 1,626 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,580 0,080 2,660 2,687 2,687 2,687 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,450 0,100 1,550 1,566 1,566 1,566 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,210 0,100 1,310 1,323 1,323 1,323 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 1,340 0,110 1,450 1,465 1,465 1,465 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,630 0,090 0,720 0,727 0,727 0,727 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,760 0,110 0,860 0,869 0,869 0,869 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,520 0,080 0,600 0,606 0,606 0,606 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,480 0,070 0,540 0,545 0,545 0,545 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,300 0,050 0,360 0,364 0,364 0,364 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,030 0,130 1,160 1,172 1,172 1,172 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,550 0,110 0,660 0,667 0,667 0,667 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,990 0,080 1,080 1,091 1,091 1,091 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,510 0,060 0,570 0,576 0,576 0,576 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 0,360 N/A 0,360 0,396 0,432 0,468 (L) 7603 Aluminium powders and flakes 0,480 N/A 0,480 0,528 0,576 0,624 (L) 7604 10 10 Bars and rods 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7604 10 90 Profiles 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7604 21 00 Hollow profiles 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7604 29 10 Bars and rods 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7604 29 90 Profiles 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7605 Aluminium wire 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7608 Aluminium tubes and pipes 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7610 10 00 Doors, windows and their frames and thresholds for doors 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7610 90 Other 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7610 90 90 Other 0,720 N/A 0,720 0,792 0,864 0,936 (L) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7613 00 00 Aluminium containers for compressed or liquefied gas 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 0,700 N/A 0,700 0,770 0,840 0,910 (L) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 1,160 N/A 1,160 1,276 1,392 1,508 (L) 7616 99 10 Cast 0,480 N/A 0,480 0,528 0,576 0,624 (L) 7616 99 90 Other 1,160 N/A 1,160 1,276 1,392 1,508 (L) Other Countries and Territories Product CN Code Description Default Value (direct emissions) Default Value (indirect emissions) Default Value (total emissions) 2026 Default Value (including mark-up) 2027 Default Value (including mark-up) 2028 and onwards Default Value (including mark-up) Underlying production route determining CBAM BM Cement 10 % mark-up 20 % mark-up 30 % mark-up 2507 00 80 Calcined clay 0,210 0,070 0,280 0,308 0,336 0,364 2523 10 00 White clinker 1,320 0,060 1,370 1,507 1,644 1,781 (B) 2523 10 00 Grey clinker 1,370 0,050 1,410 1,551 1,692 1,833 (A) 2523 21 00 White Portland cement 1,300 0,140 1,450 1,595 1,740 1,885 2523 29 00 Grey Portland cement 1,360 0,080 1,440 1,584 1,728 1,872 2523 90 00 White hydraulic cements 1,310 0,180 1,490 1,639 1,788 1,937 (B) 2523 90 00 Grey hydraulic cements 1,280 0,090 1,370 1,507 1,644 1,781 (A) 2523 30 00 Aluminous cement 1,890 0,140 2,030 2,233 2,436 2,639 Fertilisers 1 % mark-up 1 % mark-up 1 % mark-up 2808 00 00 Nitric acid; sulphonitric acids 2,770 0,040 2,810 2,838 2,838 2,838 2814 10 00 Anhydrous ammonia 2,970 0,150 3,130 3,161 3,161 3,161 2814 20 00 Ammonia in aqueous solution 0,910 0,050 0,960 0,970 0,970 0,970 2834 21 00 Nitrate of potassium 2,260 0,070 2,330 2,353 2,353 2,353 3102 Mineral or chemical fertilizers, nitrogenous see below see below see below see below see below see below 3102 10 12 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 0,860 0,040 0,900 0,909 0,909 0,909 3102 10 15 Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg) 1,430 0,040 1,470 1,485 1,485 1,485 3102 10 19 Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea) 2,600 0,120 2,720 2,747 2,747 2,747 3102 10 90 Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg) 2,540 0,120 2,660 2,687 2,687 2,687 3102 21 00 Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,870 0,100 0,970 0,980 0,980 0,980 3102 29 00 Double salts and mixtures of ammonium sulphate and ammonium nitrate 1,510 0,110 1,620 1,636 1,636 1,636 3102 30 10 Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg) 1,710 0,080 1,790 1,808 1,808 1,808 3102 30 90 Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,640 0,110 2,750 2,778 2,778 2,778 3102 40 10 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,260 0,100 2,360 2,384 2,384 2,384 3102 40 90 Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,260 0,100 2,360 2,384 2,384 2,384 3102 50 00 Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 4,320 0,070 4,390 4,434 4,434 4,434 3102 60 00 Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 2,210 0,100 2,310 2,333 2,333 2,333 3102 80 00 Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg) 1,850 0,100 1,960 1,980 1,980 1,980 3102 90 00 Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg) 2,160 0,110 2,280 2,303 2,303 2,303 3105 Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassium see below see below see below see below see below see below 3105 10 00 Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg 0,900 0,100 1 1,010 1,010 1,010 3105 20 10 Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,100 0,120 1,230 1,242 1,242 1,242 3105 20 90 Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,750 0,090 0,840 0,848 0,848 0,848 3105 30 00 Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,710 0,080 0,780 0,788 0,788 0,788 3105 40 00 Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 0,450 0,060 0,510 0,515 0,515 0,515 3105 51 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates) 1,520 0,150 1,660 1,677 1,677 1,677 3105 59 00 Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates) 0,800 0,130 0,930 0,939 0,939 0,939 3105 90 20 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg) 1,500 0,080 1,570 1,586 1,586 1,586 3105 90 80 Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg) 0,760 0,060 0,820 0,828 0,828 0,828 Aluminium 10 % mark-up 20 % mark-up 30 % mark-up 7601 Unwrought aluminium 2,203 N/A 2,203 2,423 2,643 2,863 (K) 7603 Aluminium powders and flakes 2,945 N/A 2,945 3,239 3,533 3,828 (K) 7604 10 10 Bars and rods 3,233 N/A 3,233 3,556 3,879 4,203 (K) 7604 10 90 Profiles 3,251 N/A 3,251 3,576 3,901 4,226 (K) 7604 21 00 Hollow profiles 3,251 N/A 3,251 3,576 3,901 4,226 (K) 7604 29 10 Bars and rods 3,233 N/A 3,233 3,556 3,879 4,203 (K) 7604 29 90 Profiles 3,251 N/A 3,251 3,576 3,901 4,226 (K) 7605 Aluminium wire 3,184 N/A 3,184 3,502 3,820 4,139 (K) 7606 Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm 3,717 N/A 3,717 4,088 4,460 4,831 (K) 7607 Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm 3,893 N/A 3,893 4,282 4,671 5,060 (K) 7608 Aluminium tubes and pipes 3,220 N/A 3,220 3,542 3,864 4,186 (K) 7609 00 00 Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) 3,322 N/A 3,322 3,654 3,987 4,319 (K) 7610 10 00 Doors, windows and their frames and thresholds for doors 3,212 N/A 3,212 3,533 3,854 4,176 (K) 7610 90 Other 3,212 N/A 3,212 3,533 3,854 4,176 (K) 7610 90 10 Bridges and bridge-sections, towers and lattice masts 3,212 N/A 3,212 3,533 3,854 4,176 (K) 7610 90 90 Other 3,212 N/A 3,212 3,533 3,854 4,176 (K) 7611 00 00 Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 4,037 N/A 4,037 4,441 4,845 5,249 (K) 7612 Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment 3,944 N/A 3,944 4,338 4,732 5,127 (K) 7613 00 00 Aluminium containers for compressed or liquefied gas 4,037 N/A 4,037 4,441 4,845 5,249 (K) 7614 Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated 3,297 N/A 3,297 3,627 3,957 4,286 (K) 7616 10 00 Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles 3,891 N/A 3,891 4,281 4,670 5,059 (K) 7616 91 00 Cloth, grill, netting and fencing, of aluminium wire 3,891 N/A 3,891 4,281 4,670 5,059 (K) 7616 99 10 Cast 2,953 N/A 2,953 3,248 3,544 3,839 (K) 7616 99 90 Other 3,891 N/A 3,891 4,281 4,670 5,059 (K) Hydrogen 10 % mark-up 20 % mark-up 30 % mark-up 2804 10 00 Hydrogen 17,740 N/A 17,740 19,514 21,288 23,062 Iron and steel 10 % mark-up 20 % mark-up 30 % mark-up 2601 12 00 Agglomerated iron ores and concentrates (excl. roasted iron pyrites) 0,617 0,070 0,686 0,755 0,823 0,892 7201 Pig iron and spiegeleisen, in pigs, blocks or other primary forms 3,480 N/A 3,480 3,828 4,176 4,524 7202 11 Ferro-manganese, containing by weight > 2% of carbon 1,690 N/A 1,690 1,859 2,028 2,197 7202 19 Ferro-manganese, containing by weight <= 2% carbon 5,590 N/A 5,590 6,149 6,708 7,267 7202 41 Ferro-chromium, containing by weight > 4% of carbon 2,350 N/A 2,350 2,585 2,820 3,055 7202 49 Ferro-chromium, containing by weight <= 4% of carbon 2,870 N/A 2,870 3,157 3,444 3,731 7202 60 00 Ferro-nickel 4,014 N/A 4,014 4,415 4,817 5,218 7203 Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms 1,325 N/A 1,325 1,458 1,590 1,723 7205 Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings) 3,715 N/A 3,715 4,087 4,458 4,830 (C) 7206 Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203) see below see below see below see below see below see below 7206 10 00 Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203) 3,750 N/A 3,750 4,125 4,500 4,875 (C) 7206 90 00 Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203) 3,750 N/A 3,750 4,125 4,500 4,875 (C) 7207 Semi-finished products of iron or non-alloy steel see below see below see below see below see below see below 7207 11 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 11 14 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 11 16 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 11 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7207 12 10 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 12 90 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7207 19 12 Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 19 19 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7207 19 80 Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 20 11 Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 20 15 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 20 17 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 20 19 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7207 20 32 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 20 39 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7207 20 52 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7207 20 59 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7207 20 80 Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7208 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated 4,049 N/A 4,049 4,454 4,858 5,263 (C) 7209 Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated 4,101 N/A 4,101 4,511 4,921 5,331 (C) 7210 Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 4,101 N/A 4,101 4,511 4,921 5,331 (C) 7211 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coated see below see below see below see below see below see below 7211 13 00 Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats" 4,049 N/A 4,049 4,454 4,858 5,263 (C) 7211 14 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats") 4,049 N/A 4,049 4,454 4,858 5,263 (C) 7211 19 00 Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats") 4,049 N/A 4,049 4,454 4,858 5,263 (C) 7211 23 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon 4,101 N/A 4,101 4,511 4,921 5,331 (C) 7211 29 00 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon 4,101 N/A 4,101 4,511 4,921 5,331 (C) 7211 90 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated 4,101 N/A 4,101 4,511 4,921 5,331 (C) 7212 Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated 4,101 N/A 4,101 4,511 4,921 5,331 (C) 7213 Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7214 Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils) see below see below see below see below see below see below 7214 10 00 Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils) 4,053 N/A 4,053 4,458 4,864 5,269 (C) 7214 20 00 Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7214 30 00 Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7214 91 Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7214 99 Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7215 Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s. 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7216 Angles, shapes and sections of iron or non-alloy steel, n.e.s. 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7217 Wire of iron or non-alloy steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7217 10 Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7217 20 Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7217 30 Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7217 90 Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods) 3,996 N/A 3,996 4,395 4,795 5,195 (C) 7218 Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steel see below see below see below see below see below see below 7218 10 00 Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 5,006 N/A 5,006 5,507 6,007 6,508 7218 91 Semi-finished products of stainless steel, of rectangular "other than square" cross-section 4,940 N/A 4,940 5,434 5,928 6,422 7218 99 11 Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting 4,940 N/A 4,940 5,434 5,928 6,422 7218 99 19 Semi-finished products of stainless steel, of square cross-section, forged 5,006 N/A 5,006 5,507 6,007 6,508 7218 99 20 Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting 4,940 N/A 4,940 5,434 5,928 6,422 7218 99 80 Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section) 5,006 N/A 5,006 5,507 6,007 6,508 7219 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7219 11 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 12 Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 13 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 14 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 21 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 22 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 23 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 24 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm 4,940 N/A 4,940 5,434 5,928 6,422 7219 31 00 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm 5,020 N/A 5,020 5,522 6,024 6,526 7219 32 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm 5,020 N/A 5,020 5,522 6,024 6,526 7219 33 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm 5,020 N/A 5,020 5,522 6,024 6,526 7219 34 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm 5,020 N/A 5,020 5,522 6,024 6,526 7219 35 Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm 5,020 N/A 5,020 5,522 6,024 6,526 7219 90 Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 5,020 N/A 5,020 5,522 6,024 6,526 7220 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7220 11 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm 4,940 N/A 4,940 5,434 5,928 6,422 7220 12 00 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm 4,940 N/A 4,940 5,434 5,928 6,422 7220 20 Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" 5,020 N/A 5,020 5,522 6,024 6,526 7220 90 Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked 5,020 N/A 5,020 5,522 6,024 6,526 7221 Bars and rods of stainless steel, hot-rolled, in irregularly wound coils 4,820 N/A 4,820 5,302 5,784 6,266 7222 Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s. see below see below see below see below see below see below 7222 11 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section 4,820 N/A 4,820 5,302 5,784 6,266 7222 19 Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section) 4,820 N/A 4,820 5,302 5,784 6,266 7222 20 Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished 4,820 N/A 4,820 5,302 5,784 6,266 7222 30 Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s. 5,006 N/A 5,006 5,507 6,007 6,508 7222 40 Angles, shapes and sections of stainless steel, n.e.s. 4,820 N/A 4,820 5,302 5,784 6,266 7223 Wire of stainless steel, in coils (excl. bars and rods) see below see below see below see below see below see below 7223 00 Wire of stainless steel, in coils (excl. bars and rods) 4,820 N/A 4,820 5,302 5,784 6,266 7224 Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting) see below see below see below see below see below see below 7224 10 Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting) 5,589 N/A 5,589 6,148 6,707 7,266 (F) 7224 90 02 Semi-finished products of tool steel 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 03 Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 05 Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 07 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05) 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 14 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel) 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 18 Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel) 5,589 N/A 5,589 6,148 6,707 7,266 (F) 7224 90 31 Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 38 Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum) 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7224 90 90 Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section) 5,589 N/A 5,589 6,148 6,707 7,266 (F) 7225 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7225 11 00 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented 7,100 N/A 7,100 7,810 8,520 9,230 (C) 7225 19 10 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled 5,500 N/A 5,500 6,050 6,600 7,150 (C) 7225 19 90 Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7225 30 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel) 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7225 40 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel) 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7225 50 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel) 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7225 91 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel) 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7225 92 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel) 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7225 99 00 Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel) 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7226 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" see below see below see below see below see below see below 7226 11 00 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented 7,100 N/A 7,100 7,810 8,520 9,230 (C) 7226 19 10 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled 5,500 N/A 5,500 6,050 6,600 7,150 (C) 7226 19 80 Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7226 20 00 Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced" 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7226 91 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel) 5,500 N/A 5,500 6,050 6,600 7,150 (F) 7226 92 00 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel) 5,590 N/A 5,590 6,149 6,708 7,267 (F) 7226 99 Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel) 5,588 N/A 5,588 6,147 6,706 7,264 (F) 7227 Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils 5,400 N/A 5,400 5,940 6,480 7,020 (C)/(F) 7228 Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steel see below see below see below see below see below see below 7228 10 20 Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,400 N/A 5,400 5,940 6,480 7,020 (F) 7228 10 50 Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,589 N/A 5,589 6,148 6,707 7,266 (F) 7228 10 90 Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,400 N/A 5,400 5,940 6,480 7,020 (F) 7228 20 Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,400 N/A 5,400 5,940 6,480 7,020 (F) 7228 30 Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,400 N/A 5,400 5,940 6,480 7,020 (C)/(F) 7228 40 Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,589 N/A 5,589 6,148 6,707 7,266 (F) 7228 50 Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,400 N/A 5,400 5,940 6,480 7,020 (C)/(F) 7228 60 Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils) 5,400 N/A 5,400 5,940 6,480 7,020 (F) 7228 70 Angles, shapes and sections of alloy steel other than stainless, n.e.s. 5,400 N/A 5,400 5,940 6,480 7,020 (F) 7228 80 00 Hollow drill bars and rods, of alloy or non-alloy steel 5,400 N/A 5,400 5,940 6,480 7,020 (F) 7229 Wire of alloy steel other than stainless, in coils (excl. bars and rods) 5,400 N/A 5,400 5,940 6,480 7,020 (C)/(F) 7301 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel 4,063 N/A 4,063 4,469 4,876 5,282 (C) 7302 Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails 4,887 N/A 4,887 5,376 5,864 6,353 (C) 7303 Tubes, pipes and hollow profiles, of cast iron see below see below see below see below see below see below 7303 00 Tubes, pipes and hollow profiles, of cast iron 4,150 N/A 4,150 4,565 4,980 5,395 7304 Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron) see below see below see below see below see below see below 7304 11 00 Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel 5,184 N/A 5,184 5,703 6,221 6,739 7304 19 Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron) 3,981 N/A 3,981 4,379 4,777 5,175 (C) 7304 22 00 Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas 5,184 N/A 5,184 5,703 6,221 6,739 7304 23 00 Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron) 3,981 N/A 3,981 4,379 4,777 5,175 (C) 7304 24 00 Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel 5,184 N/A 5,184 5,703 6,221 6,739 7304 29 Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron) 3,981 N/A 3,981 4,379 4,777 5,175 (C) 7304 31 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas) 3,981 N/A 3,981 4,379 4,777 5,175 (C) 7304 39 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 3,981 N/A 3,981 4,379 4,777 5,175 (C) 7304 41 00 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas) 5,184 N/A 5,184 5,703 6,221 6,739 7304 49 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas) 5,184 N/A 5,184 5,703 6,221 6,739 7304 51 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,878 N/A 3,878 4,266 4,654 5,041 (F) 7304 59 Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil) 3,878 N/A 3,878 4,266 4,654 5,041 (C)/(F) 7304 90 00 Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron) 3,981 N/A 3,981 4,379 4,777 5,175 (C) 7305 Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed" 4,060 N/A 4,060 4,466 4,872 5,278 (C) 7306 Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm) see below see below see below see below see below see below 7306 11 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 5,369 N/A 5,369 5,906 6,443 6,980 7306 19 00 Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 21 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm 5,369 N/A 5,369 5,906 6,443 6,980 7306 29 00 Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron) 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 30 12 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 30 18 Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled) 4,091 N/A 4,091 4,500 4,909 5,318 7306 30 41 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 30 49 Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc) 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 30 72 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas) 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 30 77 Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe") 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 30 80 Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe") 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 40 20 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 5,369 N/A 5,369 5,906 6,443 6,980 7306 40 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas) 5,296 N/A 5,296 5,826 6,355 6,885 7306 50 21 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" 4,129 N/A 4,129 4,541 4,954 5,367 (F) 7306 50 29 Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled) 4,057 N/A 4,057 4,462 4,868 5,273 (F) 7306 50 80 Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes) 4,129 N/A 4,129 4,541 4,954 5,367 (F) 7306 61 10 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel 5,369 N/A 5,369 5,906 6,443 6,980 7306 61 92 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 61 99 Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 69 10 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 5,369 N/A 5,369 5,906 6,443 6,980 7306 69 90 Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section) 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7306 90 00 Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm) 4,141 N/A 4,141 4,555 4,969 5,383 (C) 7307 Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steel see below see below see below see below see below see below 7307 11 Tube or pipe fittings of non-malleable cast iron 3,929 N/A 3,929 4,322 4,715 5,108 7307 19 10 Tube or pipe fittings of cast iron (excl. of non-malleable) 3,929 N/A 3,929 4,322 4,715 5,108 7307 19 90 Cast tube or pipe fittings of steel 4,053 N/A 4,053 4,459 4,864 5,269 (C) 7307 21 00 Flanges of stainless steel (excl. cast products) 4,498 N/A 4,498 4,948 5,398 5,848 7307 22 Threaded elbows, bends and sleeves of stainless steel (excl. cast products) 4,498 N/A 4,498 4,948 5,398 5,848 7307 23 Butt welding tube or pipe fittings of stainless steel (excl. cast products) 4,498 N/A 4,498 4,948 5,398 5,848 7307 29 Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings) 4,498 N/A 4,498 4,948 5,398 5,848 7307 91 00 Flanges of iron or steel (excl. cast or stainless products) 4,072 N/A 4,072 4,480 4,887 5,294 (C) 7307 92 Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products) 4,072 N/A 4,072 4,480 4,887 5,294 (C) 7307 93 Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges) 4,072 N/A 4,072 4,480 4,887 5,294 (C) 7307 99 Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings) 4,072 N/A 4,072 4,480 4,887 5,294 (C) 7308 Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406) 5,064 N/A 5,064 5,570 6,077 6,583 (C) 7309 Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport) 5,468 N/A 5,468 6,015 6,562 7,109 (C) 7310 Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s. 4,228 N/A 4,228 4,651 5,074 5,497 (C) 7311 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) see below see below see below see below see below see below 7311 00 Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport) 5,385 N/A 5,385 5,924 6,462 7,001 (C) 7318 Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded) see below see below see below see below see below see below 7318 11 00 Coach screws of iron or steel 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 12 10 Wood screws of stainless steel (excl. coach screws) 5,119 N/A 5,119 5,631 6,143 6,655 (C) 7318 12 90 Wood screws of iron or steel other than stainless (excl. coach screws) 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 13 00 Screw hooks and screw rings, of iron or steel 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 14 10 Self-tapping screws, of stainless steel (excl. wood screws) 5,119 N/A 5,119 5,631 6,143 6,655 (C) 7318 14 91 Spaced-thread screws of iron or steel other than stainless 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 14 99 Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws) 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 15 Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded) 4,801 N/A 4,801 5,281 5,761 6,242 (C) 7318 16 Nuts of iron or steel 4,693 N/A 4,693 5,162 5,632 6,101 (C) 7318 19 00 Threaded articles, of iron or steel, n.e.s. 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 21 00 Spring washers and other lock washers, of iron or steel 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 22 00 Washers of iron or steel (excl. spring washers and other lock washers) 4,322 N/A 4,322 4,754 5,186 5,618 (C) 7318 23 00 Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses) 3,963 N/A 3,963 4,360 4,756 5,152 (C) 7318 24 00 Cotters and cotter pins, of iron or steel 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7318 29 00 Non-threaded articles, of iron or steel 3,962 N/A 3,962 4,358 4,755 5,151 (C) 7326 Articles of iron or steel, n.e.s. (excl. cast articles) see below see below see below see below see below see below 7326 11 00 Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked 4,080 N/A 4,080 4,488 4,896 5,303 (C) 7326 19 Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills) 4,080 N/A 4,080 4,488 4,896 5,303 (C) 7326 20 00 Articles of iron or steel wire, n.e.s. 4,051 N/A 4,051 4,456 4,861 5,266 (C) 7326 90 30 Ladders and steps, of iron or steel 4,051 N/A 4,051 4,456 4,861 5,266 (C) 7326 90 40 Pallets and similar platforms for handling goods, of iron or steel 4,051 N/A 4,051 4,456 4,861 5,266 (C) 7326 90 50 Reels for cables, piping and the like, of iron or steel 4,051 N/A 4,051 4,456 4,861 5,266 (C) 7326 90 60 Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel 4,051 N/A 4,051 4,456 4,861 5,266 (C) 7326 90 92 Articles of iron or steel, open-die forged, n.e.s. 4,080 N/A 4,080 4,488 4,896 5,303 (C) 7326 90 94 Articles of iron or steel, closed-die forged, n.e.s. 4,080 N/A 4,080 4,488 4,896 5,303 (C) 7326 90 96 Sintered articles of iron or steel, n.e.s. 4,080 N/A 4,080 4,488 4,896 5,303 (C) 7326 90 98 Articles of iron or steel, n.e.s. 4,151 N/A 4,151 4,566 4,981 5,396 (C) (1) Commission Implementing Regulation (EU) 2025/2620 of 16 December 2025 laying down rules for the application of Regulation (EU) 2023/956 of the European Parliament and of the Council as regards the calculation of the free allocation adjustment to the number of CBAM certificates to be surrendered (OJ L, 2025/2620, 22.12.2025, ELI: http://data.europa.eu/eli/reg_impl/2025/2620/oj).

anchor annex_I · hash 81c42e14a8b3f07dbd5f5ba425743339c973a22bb9404f808280787b476a9437

Annex II

Default values for indirect emissions of goods listed in Annex I of Regulation (EU) 2023/956 and not listed in Annex II of that Regulation

Disclaimer: The data provided are based on data sourced from the International Energy Agency (IEA) and is subject to a Creative Commons Non-Commercial Share-Alike 4.0 CC BY NC SA licence ( https://creativecommons.org/licenses/by-nc-sa/4.0/deed.en ). These data are intended for the purpose of determining embedded emissions of CBAM goods under the CBAM Regulation. Any further use or redistribution of the data is permitted for non-commercial purposes only. Anyone wishing to use emissions factors data for commercial purposes is invited to contact the IEA to acquire an appropriate licence.

Country or territoryEmission factor (tCO2eq/MWh)
Albania0
Algeria0,498
Angola0,216
Argentina0,287
Armenia0,183
Australia0,645
Azerbaijan0,431
Bahrain0,697
Bangladesh0,567
Belarus0,325
Benin0,518
Bolivia0,319
Bosnia and Herzegovina0,734
Botswana1,324
Brazil0,096
Brunei0,758
Burkina Faso0,567
Cambodia0,470
Cameroon0,234
Canada0,119
Chad1,536
Chile0,356
China0,605
Colombia0,183
Congo0,640
Congo, Democratic Republic of0
Costa Rica0,011
Cuba0,555
Curaçao0,555
Dominican Republic0,548
Ecuador0,159
Egypt0,387
El Salvador0,139
Equatorial Guinea0,410
Eritrea0,754
Eswatini0,089
Ethiopia0
Gabon0,457
Georgia0,102
Ghana0,307
Gibraltar0,535
Greenland0,068
Guatemala0,299
Guyana0,820
Haiti0,691
Honduras0,314
Hong Kong0,663
India0,726
Indonesia0,791
Iran, Islamic Republic of0,529
Iraq0,653
Israel0,443
Ivory Coast0,343
Jamaica0,518
Japan0,469
Jordan0,410
Kazakhstan0,568
Kenya0,095
Korea, Republic of (South Korea)0,475
Kosovo0,909
Kuwait0,569
Kyrgyzstan0,080
Laos0,338
Lebanon0,626
Libya0,631
Madagascar0,595
Malaysia0,634
Mali0,502
Mauritania0,951
Mauritius0,765
Mexico0,413
Moldova, Republic of0,488
Mongolia1,090
Montenegro0,422
Morocco0,712
Mozambique0,083
Myanmar0,331
Namibia0,044
Nepal0
New Zealand0,115
Nicaragua0,266
Niger0,914
Nigeria0,404
North Korea (Democratic People’s Republic of Korea)0,522
North Macedonia0,641
Occupied Palestinian Territory0,493
Oman0,387
Pakistan0,377
Panama0,324
Paraguay0
Peru0,201
Philippines0,711
Qatar0,475
Russian Federation0,366
Rwanda0,340
Saudi Arabia0,611
Senegal0,567
Serbia0,729
Singapore0,381
South Africa0,963
South Sudan0,844
Sri Lanka0,520
Sudan0,235
Suriname0,505
Syria0,550
Taiwan0,561
Tajikistan0,061
Tanzania, United Republic of0,388
Thailand0,470
Togo0,423
Trinidad and Tobago0,553
Tunisia0,418
Türkiye0,420
Turkmenistan0,718
Uganda0,023
Ukraine0,310
United Arab Emirates0,451
United Kingdom0,193
United States0,358
Uruguay0,048
Uzbekistan0,519
Venezuela0,087
Viet Nam0,581
Yemen0,742
Zambia0,165
Zimbabwe0,573
Other countries and territories0,465

anchor annex_II · hash be55de334a9945ed27807f5a7afe901a72261f57c498034a1a230eceb69c14c8

Annex III

Default values for electricity imported into the customs territory of the Union

Disclaimer: The data provided are based on data sourced from the International Energy Agency (IEA) and is subject to a Creative Commons Non-Commercial Share-Alike 4.0 CC BY NC SA licence ( https://creativecommons.org/licenses/by-nc-sa/4.0/deed.en ). These data are intended for the purpose of determining embedded emissions of CBAM goods under the CBAM Regulation. Any further use or redistribution of the data is permitted for non-commercial purposes only. Anyone wishing to use emissions factors data for commercial purposes is invited to contact the IEA to acquire an appropriate licence.

Country or territoryEmission factor (tCO2eq/MWh)
Albania0
Belarus0,383
Bosnia and Herzegovina1,148
Egypt0,442
Georgia0,440
Israel0,480
Kosovo0,984
Moldova, Republic of0,530
Montenegro0,979
Morocco0,907
North Macedonia0,887
Russian Federation0,585
Serbia1,041
Tunisia0,436
Türkiye0,718
Ukraine0,907
United Kingdom0,430
European Union0,612

anchor annex_III · hash 79fcf568008f60760850968b1ff2d308edb8ce547aa8fdca935696dc4dfb8418

Annex IV

Default values for precursor for which the country of production cannot be identified

Where default values are used to determine the specific embedded emissions of a final good or of a precursor, the specific embedded free allocation shall be based on the corresponding underlying production route determining the CBAM benchmark (BM) as defined in Implementing Regulation (EU) 2025/2620 on the calculation of the free allocation adjustment to the number of CBAM certificates to be surrendered. The meaning of the indicators is as follows:

(A)

grey clinker / cement

(B)

white clinker / cement

(C)

Carbon Steel based on BF/BOF

(D)

Carbon Steel based on DRI/EAF

(E)

Carbon Steel based on Scrap/EAF

(F)

Low alloy Steel based on BF/BOF

(G)

Low alloy Steel based on DRI/EAF

(H)

Low alloy Steel based on scrap/EAF

(J)

High alloy Steel (based on EAF)

(K)

primary Aluminium

(L)

secondary Aluminium

If no production route is indicated for a CN code, the CBAM benchmark (BM) is independent of the production route.

Product CN CodeDescriptionHighest default value2026 Default Value (including mark-up)2027 Default Value (including mark-up)2028 and onwards Default Value (including mark-up)Underlying production route determining CBAM BM
Cement10 % mark-up20 % mark-up30 % mark-up
2507 00 80Calcined clay0,3200,3520,3840,416
2523 10 00White clinker1,4101,5511,6921,833(B)
2523 10 00Grey clinker1,4401,5841,7281,872(A)
2523 21 00White Portland cement1,4801,6281,7761,924
2523 29 00Grey Portland cement1,4901,6391,7881,937
2523 90 00White hydraulic cements1,5301,6831,8361,989(B)
2523 90 00Grey hydraulic cements1,4201,5621,7041,846(A)
2523 30 00Aluminous cement2,2902,5192,7482,977
Fertilisers1 % mark-up1 % mark-up1 % mark-up
2808 00 00Nitric acid; sulphonitric acids3,0803,1113,1113,111
2814 10 00Anhydrous ammonia4,3604,4044,4044,404
2814 20 00Ammonia in aqueous solution1,3101,3231,3231,323
2834 21 00Nitrate of potassium2,8502,8792,8792,879
3102Mineral or chemical fertilizers, nitrogenousSee belowSee belowSee belowSee below
3102 10 12Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing =>31,8% but <=33,2 % by weight of urea (excl. that in packages with a gross weight of <= 10 kg)1,5401,5551,5551,555
3102 10 15Urea in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product and containing >33,2% but <=55% by weight of urea (excl. that in packages with a gross weight of <= 10 kg)2,5302,5552,5552,555
3102 10 19Urea, whether or not in aqueous solution, containing >45% nitrogen in relation to the weight of the dry product (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg, or in aqueous solution containing =>31,8% but <=55% by weight of urea)4,6404,6864,6864,686
3102 10 90Urea, whether or not in aqueous solution, containing <= 45% by weight of nitrogen on the dry anhydrous product (excl. goods of this chapter in tablets or similar forms or in packages of a gross weight of <= 10 kg)4,5304,5754,5754,575
3102 21 00Ammonium sulphate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg)1,2901,3031,3031,303
3102 29 00Double salts and mixtures of ammonium sulphate and ammonium nitrate2,1302,1512,1512,151
3102 30 10Ammonium nitrate in aqueous solution (excl. that in packages with a gross weight of <= 10 kg)2,1902,2122,2122,212
3102 30 90Ammonium nitrate (excl. that in aqueous solution, in tablets or similar forms, or in packages with a gross weight of <= 10 kg)3,3703,4043,4043,404
3102 40 10Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing <= 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg)2,9002,9292,9292,929
3102 40 90Mixtures of ammonium nitrate with calcium carbonate or other inorganic non-fertilising substances, for use as fertilisers, containing > 28% nitrogen by weight (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg)2,9002,9292,9292,929
3102 50 00Sodium nitrate (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg)4,8104,8584,8584,858
3102 60 00Double salts and mixtures of calcium nitrate and ammonium nitrate (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg)2,8302,8582,8582,858
3102 80 00Mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution (excl. those in packages with a gross weight of <= 10 kg)2,4102,4342,4342,434
3102 90 00Mineral or chemical nitrogen fertilisers (excl. urea; ammonium sulphate; ammonium nitrate; sodium nitrate; double salts and mixtures of ammonium nitrate with ammonium sulphate or calcium; mixtures of urea and ammonium nitrate in aqueous or ammoniacal solution; mixtures of ammonium nitrate and calcium carbonate or other non-fertilising inorganic elements; in tablets or similar in packages <= 10 kg)3,1103,1413,1413,141
3105Mineral or chemical fertilisers containing two or three of the fertilising elements nitrogen, phosphorus and potassiumSee belowSee belowSee belowSee below
3105 10 00Mineral or chemical fertilisers of animal or vegetable origin, in tablets or similar forms, or in packages with a gross weight of <= 10 kg1,3101,3231,3231,323
3105 20 10Mineral or chemical fertilisers containing phosphorus and potassium, with a nitrogen content > 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg)1,5301,5451,5451,545
3105 20 90Mineral or chemical fertilisers containing nitrogen, phosphorus and potassium, with a nitrogen content <= 10 % by weight on the dry anhydrous product (excl. those in tablets or similar forms, or in packages with a gross weight of <= 10 kg)1,0501,0611,0611,061
3105 30 00Diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg)1,0401,0501,0501,050
3105 40 00Ammonium dihydrogenorthophosphate "monoammonium phosphate", whether or not mixed with diammonium hydrogenorthophosphate "diammonium phosphate" (excl. that in tablets or similar forms, or in packages with a gross weight of <= 10 kg)0,6700,6770,6770,677
3105 51 00Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (nitrates and phosphates)2,0702,0912,0912,091
3105 59 00Other mineral or chemical fertilisers containing the two fertilising elements nitrogen and phosphorus (excl. nitrates and phosphates)1,2401,2521,2521,252
3105 90 20Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one principal fertilising substance only, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, containing > 10% nitrogen by weight (excl. in tablets or similar forms, or in packages with a gross weight of <= 10 kg)1,9601,9801,9801,980
3105 90 80Mineral or chemical fertilisers containing the two fertilising elements nitrogen and potassium, or one main fertilising element, incl. mixtures of animal or vegetable fertilisers with chemical or mineral fertilisers, not containing nitrogen or with a nitrogen content, by weight, of <= 10% (excl. in tablets or similar forms or in packages of a gross weight of <= 10 kg)1,0201,0301,0301,030
Aluminium10 % mark-up20 % mark-up30 % mark-up
7601Unwrought aluminium3,1983,5183,8384,157(K)
7603Aluminium powders and flakes4,1484,5634,9785,392(K)
7604 10 10Bars and rods4,8815,3695,8576,345(K)
7604 10 90Profiles4,8815,3695,8576,345(K)
7604 21 00Hollow profiles4,8815,3695,8576,345(K)
7604 29 10Bars and rods4,8815,3695,8576,345(K)
7604 29 90Profiles4,8815,3695,8576,345(K)
7605Aluminium wire4,8815,3695,8576,345(K)
7606Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm4,9865,4855,9846,482(K)
7607Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm5,5596,1156,6717,227(K)
7608Aluminium tubes and pipes4,8965,3855,8756,364(K)
7609 00 00Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves)4,8965,3855,8756,364(K)
7610 10 00Doors, windows and their frames and thresholds for doors4,8965,3855,8756,364(K)
7610 90Other4,8965,3855,8756,364(K)
7610 90 10Bridges and bridge-sections, towers and lattice masts4,8965,3855,8756,364(K)
7610 90 90Other4,8965,3855,8756,364(K)
7611 00 00Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment5,5596,1156,6717,227(K)
7612Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment5,5596,1156,6717,227(K)
7613 00 00Aluminium containers for compressed or liquefied gas5,5596,1156,6717,227(K)
7614Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated4,8815,3695,8576,345(K)
7616 10 00Nails, tacks, staples (other than those of heading 8305), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles5,5596,1156,6717,227(K)
7616 91 00Cloth, grill, netting and fencing, of aluminium wire5,5596,1156,6717,227(K)
7616 99 10Cast3,0803,3883,6964,004(K)
7616 99 90Other3,7704,1474,5244,901(K)
Hydrogen10 % mark-up20 % mark-up30 % mark-up
2804 10 00Hydrogen26,64029,30431,96834,632
Iron and steel10 % mark-up20 % mark-up30 % mark-up
2601 12 00Agglomerated iron ores and concentrates (excl. roasted iron pyrites)1,6101,7711,9322,093
7201Pig iron and spiegeleisen, in pigs, blocks or other primary forms7,9208,7129,50410,296
7202 11Ferro-manganese, containing by weight > 2% of carbon1,6901,8592,0282,197
7202 19Ferro-manganese, containing by weight <= 2% carbon5,5906,1496,7087,267
7202 41Ferro-chromium, containing by weight > 4% of carbon2,3502,5852,8203,055
7202 49Ferro-chromium, containing by weight <= 4% of carbon2,8703,1573,4443,731
7202 60 00Ferro-nickel6,1506,7657,3807,995
7203Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99,94%, in lumps, pellets or similar forms4,2004,6205,0405,460
7205Granules and powders of pig iron, spiegeleisen, iron or steel (excl. granules and powders of ferro-alloys, turnings and filings of iron or steel, radioactive iron powders "isotopes" and certain low-calibre, substandard balls for ballbearings)7,9008,6909,48010,270(C)
7206Iron and non-alloy steel in ingots or other primary forms (excl. remelting scrap ingots, products obtained by continuous casting and iron of heading 7203)see belowsee belowsee belowsee below
7206 10 00Ingots, of iron and non-alloy steel (excl. remelted scrap ingots, continuous cast products, iron of heading 7203)8,2109,0319,85210,673(C)
7206 90 00Iron and non-alloy steel, in puddled bars or other primary forms (excl. ingots, remelted scrap ingots, continuous cast products, iron of heading 7203)8,2109,0319,85210,673(C)
7207Semi-finished products of iron or non-alloy steelsee belowsee belowsee belowsee below
7207 11 11Semi-finished products, of non-alloy free-cutting steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting8,2309,0539,87610,699(C)
7207 11 14Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of <= 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel)8,2309,0539,87610,699(C)
7207 11 16Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness of > 130 mm, rolled or obtained by continuous casting (excl. free-cutting steel)8,2309,0539,87610,699(C)
7207 11 90Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular cross-section, the width < twice the thickness, forged8,2109,0319,85210,673(C)
7207 12 10Semi-finished products of iron or non-alloy steel, containing by weight < 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting8,2309,0539,87610,699(C)
7207 12 90Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of rectangular "other than square" cross-section, the width >= twice the thickness, forged8,2109,0319,85210,673(C)
7207 19 12Semi-finished products, of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting8,2309,0539,87610,699(C)
7207 19 19Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon, of circular or polygonal cross-section, forged8,2109,0319,85210,673(C)
7207 19 80Semi-finished products of iron or non-alloy steel, containing by weight < 0,25% carbon (excl. semi-products, of square, rectangular, circular or polygonal cross-section)8,2309,0539,87610,699(C)
7207 20 11Semi-finished products, of non-alloy free-cutting steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting8,2309,0539,87610,699(C)
7207 20 15Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% but < 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel)8,2309,0539,87610,699(C)
7207 20 17Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of square or rectangular cross-section, the width < twice the thickness, rolled or obtained by continuous casting (excl. free-cutting steel)8,2309,0539,87610,699(C)
7207 20 19Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of square or rectangular cross-section, the width < twice the thickness, forged8,2109,0319,85210,673(C)
7207 20 32Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25 of carbon, of rectangular "other than square" cross-section, the width measuring >= twice the thickness, rolled or obtained by continuous casting8,2309,0539,87610,699(C)
7207 20 39Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of rectangular "other than square" cross-section and the width >= twice the thickness, forged8,2109,0319,85210,673(C)
7207 20 52Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon, of circular or polygonal cross-section, rolled or obtained by continuous casting8,2309,0539,87610,699(C)
7207 20 59Semi-finished products of iron or non-alloy steel, containing by weight >= 0,6% carbon, of circular or polygonal cross-section, forged8,2109,0319,85210,673(C)
7207 20 80Semi-finished products of iron or non-alloy steel, containing by weight >= 0,25% carbon (excl. those of square, rectangular, circular or polygonal cross-section)8,2309,0539,87610,699(C)
7208Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled, not clad, plated or coated8,2309,0539,87610,699(C)
7209Flat-rolled products of iron or non-alloy steel, of a width of >= 600 mm, cold-rolled "cold-reduced", not clad, plated or coated8,2509,0759,90010,725(C)
7210Flat-rolled products of iron or non-alloy steel, of a width >= 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated8,2509,0759,90010,725(C)
7211Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", not clad, plated or coatedsee belowsee belowsee belowsee below
7211 13 00Flat-rolled products of iron or non-alloy steel, simply hot-rolled on four faces or in a closed box pass, not clad, plated or coated, of a width of > 150 mm but < 600 mm and a thickness of >= 4 mm, not in coils, without patterns in relief, commonly known as "wide flats"8,2309,0539,87610,699(C)
7211 14 00Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, not further worked than hot-rolled, not clad, plated or coated, of a thickness of >= 4,75 mm (excl. "wide flats")8,2309,0539,87610,699(C)
7211 19 00Flat-rolled products of iron or non-alloy steel, of a width < 600 mm, simply hot-rolled, not clad, plated or coated, of a thickness < 4,75 mm (excl. "wide flats")8,2309,0539,87610,699(C)
7211 23Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight < 0,25% of carbon8,2509,0759,90010,725(C)
7211 29 00Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, simply cold-rolled "cold-reduced", not clad, plated or coated, containing by weight >= 0,25% of carbon8,2509,0759,90010,725(C)
7211 90Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked, but not clad, plated or coated8,2509,0759,90010,725(C)
7212Flat-rolled products of iron or non-alloy steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", clad, plated or coated8,2509,0759,90010,725(C)
7213Bars and rods of iron or non-alloy steel, hot-rolled, in irregularly wound coils8,2309,0539,87610,699(C)
7214Bars and rods, of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but incl. those twisted after rolling (excl. in irregularly wound coils)see belowsee belowsee belowsee below
7214 10 00Bars and rods, of iron or non-alloy steel, not further worked than forged (excl. in irregularly wound coils)8,2109,0319,85210,673(C)
7214 20 00Bars and rods, of iron or non-alloy steel, with indentations, ribs, groves or other deformations produced during the rolling process8,2309,0539,87610,699(C)
7214 30 00Bars and rods, of non-alloy free-cutting steel, not further worked than hot-rolled, hot-drawn or hot-extruded (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling)8,2309,0539,87610,699(C)
7214 91Bars and rods, of iron or non-alloy steel, not further worked than hot-rolled, hot-drawn or hot-extruded, of rectangular "other than square" cross-section (excl. containing indentations, ribs, grooves or other deformations produced during the rolling process, bars and rods twisted after rolling and free-cutting steel)8,2309,0539,87610,699(C)
7214 99Bars and rods, of iron or non-alloy steel, only hot-rolled, only hot-drawn or only hot-extruded (excl. of rectangular [other than square] cross-section and those containing indentations, ribs, grooves or other deformations produced during the rolling process, and of non-alloy free-cutting steel)8,2309,0539,87610,699(C)
7215Bars and rods, of iron or non-alloy steel, cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked, n.e.s.8,2309,0539,87610,699(C)
7216Angles, shapes and sections of iron or non-alloy steel, n.e.s.8,2309,0539,87610,699(C)
7217Wire of iron or non-alloy steel, in coils (excl. bars and rods)see belowsee belowsee belowsee below
7217 10Wire of iron or non-alloy steel, in coils, not plated or coated, whether or not polished (excl. bars and rods)8,2309,0539,87610,699(C)
7217 20Wire of iron or non-alloy steel, in coils, plated or coated with zinc (excl. bars and rods)8,2309,0539,87610,699(C)
7217 30Wire of iron or non-alloy steel, in coils, plated or coated with base metals (excl. plated or coated with zinc, and bars and rods)8,2309,0539,87610,699(C)
7217 90Wire of iron or non-alloy steel, in coils, plated or coated (excl. plated or coated with base metals, and bars and rods)8,2309,0539,87610,699(C)
7218Stainless steel in ingots or other primary forms (excl. remelting scrap ingots and products obtained by continuous casting); semi-finished products of stainless steelsee belowsee belowsee belowsee below
7218 10 00Steel, stainless, in ingots and other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting)8,6309,49310,35611,219
7218 91Semi-finished products of stainless steel, of rectangular "other than square" cross-section8,6709,53710,40411,271
7218 99 11Semi-finished products of stainless steel, of square cross-section, rolled or obtained by continuous casting8,6709,53710,40411,271
7218 99 19Semi-finished products of stainless steel, of square cross-section, forged8,6309,49310,35611,219
7218 99 20Semi-finished products of stainless steel, of circular cross-section or of cross-section other than square or rectangular, rolled or obtained by continuous casting8,6709,53710,40411,271
7218 99 80Semi-finished products of stainless steel, forged (excl. products of square or rectangular cross-section)8,6309,49310,35611,219
7219Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced"see belowsee belowsee belowsee below
7219 11 00Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of > 10 mm8,6709,53710,40411,271
7219 12Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 4,7 mm and <= 10 mm8,6709,53710,40411,271
7219 13Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of >= 3 mm and < 4,75 mm8,6709,53710,40411,271
7219 14Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, in coils, of a thickness of < 3 mm8,6709,53710,40411,271
7219 21Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of > 10 mm8,6709,53710,40411,271
7219 22Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 4,75 mm and <= 10 mm8,6709,53710,40411,271
7219 23 00Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of >= 3 mm and < 4,75 mm8,6709,53710,40411,271
7219 24 00Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than hot-rolled, not in coils, of a thickness of < 3 mm8,6709,53710,40411,271
7219 31 00Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 4,75 mm8,6909,55910,42811,297
7219 32Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 3 mm but < 4,75 mm8,6909,55910,42811,297
7219 33Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of > 1 mm but < 3 mm8,6909,55910,42811,297
7219 34Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of >= 0,5 mm but <= 1 mm8,6909,55910,42811,297
7219 35Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced", of a thickness of < 0,5 mm8,6909,55910,42811,297
7219 90Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked8,6909,55910,42811,297
7220Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced"see belowsee belowsee belowsee below
7220 11 00Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of >= 4,75 mm8,6709,53710,40411,271
7220 12 00Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than hot-rolled, of a thickness of < 4,75 mm8,6709,53710,40411,271
7220 20Flat-rolled products of stainless steel, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced"8,6909,55910,42811,297
7220 90Flat-rolled products of stainless steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked8,6909,55910,42811,297
7221Bars and rods of stainless steel, hot-rolled, in irregularly wound coils8,6909,55910,42811,297
7222Other bars and rods of stainless steel; angles, shapes and sections of stainless steel, n.e.s.see belowsee belowsee belowsee below
7222 11Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only hot-extruded, of circular cross-section8,6909,55910,42811,297
7222 19Bars and rods of stainless steel, only hot-rolled, only hot-drawn or only extruded (excl. of circular cross-section)8,6909,55910,42811,297
7222 20Other bars and rods of stainless steel, not further worked than cold-formed or cold-finished8,6909,55910,42811,297
7222 30Other bars and rods of stainless steel, cold-formed or cold-finished and further worked, or not further worked than forged, or forged, or hot-formed by other means and further worked, n.e.s.8,6309,49310,35611,219
7222 40Angles, shapes and sections of stainless steel, n.e.s.8,6909,55910,42811,297
7223Wire of stainless steel, in coils (excl. bars and rods)see belowsee belowsee belowsee below
7223 00Wire of stainless steel, in coils (excl. bars and rods)8,6909,55910,42811,297
7224Steel, alloy, other than stainless, in ingots or other primary forms, semi-finished products of alloy steel other than stainless (excl. waste and scrap in ingot form, and products obtained by continuous casting)see belowsee belowsee belowsee below
7224 10Steel, alloy, other than stainless, in ingots or other primary forms (excl. waste and scrap in ingot form, and products obtained by continuous casting)9,96010,95611,95212,948(F)
7224 90 02Semi-finished products of tool steel10111213(F)
7224 90 03Semi-finished products of high-speed steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting the width measuring < twice the thickness10111213(F)
7224 90 05Semi-finished products of steel containing by weight <= 0,7% of carbon, 0,5% to 1,2% of manganese, 0,6% to 2,3% of silicon, or of steel containing by weight >= 0,0008% of boron with any other element < the minimum content referred to in Note 1 f to chapter 72, of square or rectangular cross-section, hot rolled or obtained by continuous casting, the width measuring < twice the thickness10111213(F)
7224 90 07Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring < twice the thickness (excl. of tool steel, high-speed steel and articles of subheading 7224.90.05)10111213(F)
7224 90 14Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, hot-rolled or obtained by continuous casting, the width measuring >= twice the thickness (excl. of tool steel)10111213(F)
7224 90 18Semi-finished products of alloy steel other than stainless steel, of square or rectangular cross-section, forged (excl. of tool steel)9,96010,95611,95212,948(F)
7224 90 31Semi-finished products of steel containing by weight 0,9% to 1,15% carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting10111213(F)
7224 90 38Semi-finished products of alloy steel, other than stainless steel, cut into shapes other than square or rectangular, hot-rolled or obtained by continuous casting (excl. of tool steel and products containing by weight 0,9% to 1,15% of carbon, 0,5% to 2% of chromium and, if present, <= 0,5% of molybdenum)10111213(F)
7224 90 90Semi-finished products of alloy steel, other than stainless steel, forged (excl. of tool steel and products of square or rectangular, circular or polygamol cross-section)9,96010,95611,95212,948(F)
7225Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced"see belowsee belowsee belowsee below
7225 11 00Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, grain-oriented13,24014,56415,88817,212(C)
7225 19 10Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, hot-rolled10111213(C)
7225 19 90Flat-rolled products of silicon-electrical steel, of a width of >= 600 mm, cold-rolled "cold-reduced", non-grain-oriented10,02011,02212,02413,026(F)
7225 30Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, in coils (excl. products of silicon-electrical steel)10111213(F)
7225 40Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than hot-rolled, not in coils (excl. products of silicon-electrical steel)10111213(F)
7225 50Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of silicon-electrical steel)10,02011,02212,02413,026(F)
7225 91 00Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and electrolytically plated or coated with zinc (excl. products of silicon-electrical steel)10,02011,02212,02413,026(F)
7225 92 00Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and plated or coated with zinc (excl. electrolytically plated or coated and products of silicon-electrical steel)10,02011,02212,02413,026(F)
7225 99 00Flat-rolled products of alloy steel other than stainless, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. plated or coated with zinc and products of silicon-electrical steel)10,02011,02212,02413,026(F)
7226Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced"see belowsee belowsee belowsee below
7226 11 00Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced", grain-oriented13,24014,56415,88817,212(C)
7226 19 10Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, not further worked than hot-rolled10111213(C)
7226 19 80Flat-rolled products of silicon-electrical steel, of a width of < 600 mm, cold-rolled "cold-reduced", whether or not further worked, or hot-rolled and further worked, non-grain-oriented10,02011,02212,02413,026(F)
7226 20 00Flat-rolled products of high-speed steel, of a width of <= 600 mm, hot-rolled or cold-rolled "cold-reduced"10111213(F)
7226 91Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than hot-rolled (excl. products of high-speed steel or silicon-electrical steel)10111213(F)
7226 92 00Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, not further worked than cold-rolled "cold-reduced" (excl. products of high-speed steel or silicon-electrical steel)10,02011,02212,02413,026(F)
7226 99Flat-rolled products of alloy steel other than stainless, of a width of < 600 mm, hot-rolled or cold-rolled "cold-reduced" and further worked (excl. products of high-speed steel or silicon-electrical steel)10,02011,02212,02413,026(F)
7227Bars and rods of alloy steel other than stainless, hot-rolled, in irregularly wound coils10,02011,02212,02413,026(C)/(F)
7228Other bars and rods of alloy steel other than stainless, angles, shapes and sections of alloy steel other than stainless, n.e.s.; hollow drill bars and rods, of alloy or non-alloy steelsee belowsee belowsee belowsee below
7228 10 20Bars and rods of high-speed steel, not further worked than hot-rolled, hot-drawn or extruded, and hot-rolled, hot-drawn or extruded, not further worked than clad (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)10,02011,02212,02413,026(F)
7228 10 50Bars and rods of high-speed steel, forged (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)9,96010,95611,95212,948(F)
7228 10 90Bars and rods of high-speed steel, not further worked than cold-formed or cold-finished, whether or not further worked, or hot-formed and further worked (excl. forged products, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)10,02011,02212,02413,026(F)
7228 20Bars and rods of silico-manganese steel (excl. semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)10,02011,02212,02413,026(F)
7228 30Bars and rods of alloy steel other than stainless, not further worked than hot-rolled, hot-drawn or extruded (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)10,02011,02212,02413,026(C)/(F)
7228 40Bars and rods of alloy steel other than stainless, not further worked than forged (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)9,96010,95611,95212,948(F)
7228 50Bars and rods of alloy steel other than stainless, not further worked than cold-formed or cold-finished (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)10,02011,02212,02413,026(C)/(F)
7228 60Bars and rods of alloy steel other than stainless, cold-formed or cold-finished and further worked or hot-formed and further worked, n.e.s. (excl. products of high-speed steel or silico-manganese steel, semi-finished products, flat-rolled products and hot-rolled bars and rods in irregularly wound coils)10,02011,02212,02413,026(F)
7228 70Angles, shapes and sections of alloy steel other than stainless, n.e.s.10,02011,02212,02413,026(F)
7228 80 00Hollow drill bars and rods, of alloy or non-alloy steel10,02011,02212,02413,026(F)
7229Wire of alloy steel other than stainless, in coils (excl. bars and rods)10,02011,02212,02413,026(C)/(F)
7301Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel8,2509,0759,90010,725(C)
7302Railway or tramway track construction material of iron or steel, the following : rails, check-rails and rack rails, switch blades, crossing frogs, point rods and other crossing pieces, sleepers "cross-ties", fish-plates, chairs, chair wedges, sole plates "base plates", rail clips, bedplates, ties and other material specialised for jointing or fixing rails8,2109,0319,85210,673(C)
7303Tubes, pipes and hollow profiles, of cast ironsee belowsee belowsee belowsee below
7303 00Tubes, pipes and hollow profiles, of cast iron7,8908,6799,46810,257
7304Tubes, pipes and hollow profiles, seamless, of iron or steel (excl. products of cast iron)see belowsee belowsee belowsee below
7304 11 00Line pipe of a kind used for oil or gas pipelines, seamless, of stainless steel8,6309,49310,35611,219
7304 19Line pipe of a kind used for oil or gas pipelines, seamless, of iron or steel (excl. products of stainless steel or of cast iron)8,2109,0319,85210,673(C)
7304 22 00Drill pipe, seamless, of stainless steel, of a kind used in drilling for oil or gas8,6309,49310,35611,219
7304 23 00Drill pipe, seamless, of a kind used in drilling for oil or gas, of iron or steel (excl. products of stainless steel or of cast iron)8,2109,0319,85210,673(C)
7304 24 00Casing and tubing, seamless, of a kind used for drilling for oil or gas, of stainless steel8,6309,49310,35611,219
7304 29Casing and tubing, seamless, of iron or steel, of a kind used in drilling for oil or gas (excl. products of cast iron)8,2109,0319,85210,673(C)
7304 31Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used for drilling for oil or gas)8,2109,0319,85210,673(C)
7304 39Tubes, pipes and hollow profiles, seamless, of circular cross-section, of iron or non-alloy steel, not cold-drawn or cold-rolled "cold-reduced" (excl. cast iron products, line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas)8,2109,0319,85210,673(C)
7304 41 00Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil or gas)8,6309,49310,35611,219
7304 49Tubes, pipes and hollow profiles, seamless, of circular cross-section, of stainless steel, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines or of a kind used for drilling for oil or gas)8,6309,49310,35611,219
7304 51Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil)7,8608,6469,43210,218(F)
7304 59Tubes, pipes and hollow profiles, seamless, of circular cross-section, of alloy steel other than stainless, not cold-drawn or cold-rolled "cold-reduced" (excl. line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used for drilling for oil)7,8608,6469,43210,218(C)/(F)
7304 90 00Tubes, pipes and hollow profiles, seamless, of non-circular cross-section, of iron or steel (excl. products of cast iron)8,2109,0319,85210,673(C)
7305Tubes and pipes, having circular cross-sections and an external diameter of > 406,4 mm, of flat-rolled products of iron or steel "e.g., welded, riveted or similarly closed"8,2509,0759,90010,725(C)
7306Tubes, pipes and hollow profiles "e.g., open seam or welded, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless tubes and pipes and tubes having internal and external circular cross-sections and an external diameter of > 406,4 mm)see belowsee belowsee belowsee below
7306 11 00Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm8,6909,55910,42811,297
7306 19 00Line pipe of a kind used for oil or gas pipelines, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron)8,2509,0759,90010,725(C)
7306 21 00Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of stainless steel, of an external diameter of <= 406,4 mm8,6909,55910,42811,297
7306 29 00Casing and tubing of a kind used in drilling for oil or gas, welded, of flat-rolled products of iron or steel, of an external diameter of <= 406,4 mm (excl. products of stainless steel or of cast iron)8,2509,0759,90010,725(C)
7306 30 12Precision tubes, welded, of circular cross-section, of iron or non-alloy steel, cold-drawn or cold-rolled "cold-reduced"8,2509,0759,90010,725(C)
7306 30 18Precision tubes, welded, of circular cross-section, of iron or non-alloy steel (excl. cold-drawn or cold-rolled)8,2309,0539,87610,699
7306 30 41Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel, plated or coated with zinc8,2509,0759,90010,725(C)
7306 30 49Threaded or threadable tubes "gas pipe", welded, of circular cross-section, of iron or non-alloy steel (excl. products plated or coated with zinc)8,2509,0759,90010,725(C)
7306 30 72Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel, of an external diameter of <= 168,3 mm, plated or coated with zinc (excl. line pipe of a kind used for oil or gas pipelines or casing and tubingof a kind used in drilling for oil or gas)8,2509,0759,90010,725(C)
7306 30 77Other tubes, pipes and hollow profiles, welded, of circular cross-section, of iron or non-alloy steel of an external diameter of <= 168,3 mm (excl. plated or coated with zinc and line pipe of a kind used for oil or gas pipelines, casing and tubing of a kind used in drilling for oil or gas, precision tubes and threaded or threadable tubes "gas pipe")8,2509,0759,90010,725(C)
7306 30 80Tubes, pipes and hollow profiles, welded, having a circular cross-section, of iron or steel, of an external diameter of > 168,3 mm but <= 406,4 mm (excl. line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, or precision steel tubes, electrical conduit tubes or threaded or threadable tubes "gas pipe")8,2509,0759,90010,725(C)
7306 40 20Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel, cold-drawn or cold-rolled "cold-reduced" (excl. products having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas)8,6909,55910,42811,297
7306 40 80Tubes, pipes and hollow profiles, welded, of circular cross-section, of stainless steel (excl. products cold-drawn or cold-rolled "cold-reduced", tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas)8,6709,53710,40411,271
7306 50 21Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless, cold-drawn or cold-rolled "cold-reduced"7,9608,7569,55210,348(F)
7306 50 29Precision steel tubes, welded, of circular cross-section, of alloy steel other than stainless (excl. cold-drawn or cold-rolled)7,9408,7349,52810,322(F)
7306 50 80Tubes, pipes and hollow profiles, welded, of circular cross-section, of alloy steel other than stainless (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, and line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and precision steel tubes)7,9608,7569,55210,348(F)
7306 61 10Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of stainless steel8,6909,55910,42811,297
7306 61 92Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of <= 2 mm8,2509,0759,90010,725(C)
7306 61 99Tubes and pipes and hollow profiles, welded, of square or rectangular cross-section, of iron or steel other than stainless steel, with a wall thickness of > 2 mm8,2509,0759,90010,725(C)
7306 69 10Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section)8,6909,55910,42811,297
7306 69 90Tubes, pipes and hollow profiles, welded, of non-circular cross-section, of iron or steel other than stainless steel (excl. tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm, line pipe of a kind used for oil or gas pipelines or casing and tubing of a kind used in drilling for oil or gas, and tubes and pipes and hollow profiles of square or rectangular cross-section)8,2509,0759,90010,725(C)
7306 90 00Tubes, pipes and hollow profiles "e.g., open seam, riveted or similarly closed", of iron or steel (excl. of cast iron, seamless or welded tubes and pipes and tubes and pipes having internal and external circular cross-sections and an external diameter of > 406,4 mm)8,2509,0759,90010,725(C)
7307Tube or pipe fittings "e.g. couplings, elbows, sleeves", of iron or steelsee belowsee belowsee belowsee below
7307 11Tube or pipe fittings of non-malleable cast iron7,8908,6799,46810,257
7307 19 10Tube or pipe fittings of cast iron (excl. of non-malleable)7,8908,6799,46810,257
7307 19 90Cast tube or pipe fittings of steel8,2109,0319,85210,673(C)
7307 21 00Flanges of stainless steel (excl. cast products)7,9408,7349,52810,322
7307 22Threaded elbows, bends and sleeves of stainless steel (excl. cast products)7,9408,7349,52810,322
7307 23Butt welding tube or pipe fittings of stainless steel (excl. cast products)7,9408,7349,52810,322
7307 29Tube or pipe fittings of stainless steel (excl. cast products, flanges, threaded elbows, bends and sleeves and butt weldings fittings)7,9408,7349,52810,322
7307 91 00Flanges of iron or steel (excl. cast or stainless products)8,2109,0319,85210,673(C)
7307 92Threaded elbows, bends and sleeves, of stainless steel (excl. cast or stainless products)8,2109,0319,85210,673(C)
7307 93Butt welding fittings of iron or steel (excl. cast iron or stainless steel products, and flanges)8,2109,0319,85210,673(C)
7307 99Tube or pipe fittings, of iron or steel (excl. cast iron or stainless steel products; flanges; threaded elbows, bends and sleeves; butt welding fittings)8,2109,0319,85210,673(C)
7308Structures and parts of structures "e.g., bridges and bridge-sections, lock-gates, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, shutters, balustrades, pillars and columns", of iron or steel; plates, rods, angles, shapes, sections, tubes and the like, prepared for use in structures, of iron or steel (excl. prefabricated buildings of heading 9406)8,2509,0759,90010,725(C)
7309Reservoirs, tanks, vats and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of > 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated (excl. containers specifically constructed or equipped for one or more types of transport)10,01011,01112,01213,013(C)
7310Tanks, casks, drums, cans, boxes and similar containers, of iron or steel, for any material "other than compressed or liquefied gas", of a capacity of <= 300 l, not fitted with mechanical or thermal equipment, whether or not lined or heat-insulated, n.e.s.8,2509,0759,90010,725(C)
7311Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport)see belowsee belowsee belowsee below
7311 00Containers of iron or steel, for compressed or liquefied gas (excl. containers specifically constructed or equipped for one or more types of transport)9,98010,97811,97612,974(C)
7318Screws, bolts, nuts, coach screws, screw hooks, rivets, cotters, cotter pins, washers, incl. spring washers, and similar articles, of iron or steel (excl. lag screws, stoppers, plugs and the like, threaded)see belowsee belowsee belowsee below
7318 11 00Coach screws of iron or steel8,2309,0539,87610,699(C)
7318 12 10Wood screws of stainless steel (excl. coach screws)8,6509,51510,38011,245(C)
7318 12 90Wood screws of iron or steel other than stainless (excl. coach screws)8,2309,0539,87610,699(C)
7318 13 00Screw hooks and screw rings, of iron or steel8,2309,0539,87610,699(C)
7318 14 10Self-tapping screws, of stainless steel (excl. wood screws)8,6509,51510,38011,245(C)
7318 14 91Spaced-thread screws of iron or steel other than stainless8,2309,0539,87610,699(C)
7318 14 99Self-tapping screws of iron or steel other than stainless (excl. spaced-thread screws and wood screws)8,2309,0539,87610,699(C)
7318 15Threaded screws and bolts, of iron or steel, whether or not with their nuts and washers (excl. coach screws and other wood screws, screw hooks and screw rings, self-tapping screws, lag screws, stoppers, plugs and the like, threaded)8,2309,0539,87610,699(C)
7318 16Nuts of iron or steel8,5409,39410,24811,102(C)
7318 19 00Threaded articles, of iron or steel, n.e.s.8,2309,0539,87610,699(C)
7318 21 00Spring washers and other lock washers, of iron or steel8,2309,0539,87610,699(C)
7318 22 00Washers of iron or steel (excl. spring washers and other lock washers)8,5409,39410,24811,102(C)
7318 23 00Rivets of iron or steel (excl. tubular and bifurcated rivets for particular uses)8,2309,0539,87610,699(C)
7318 24 00Cotters and cotter pins, of iron or steel8,2309,0539,87610,699(C)
7318 29 00Non-threaded articles, of iron or steel8,2309,0539,87610,699(C)
7326Articles of iron or steel, n.e.s. (excl. cast articles)see belowsee belowsee belowsee below
7326 11 00Grinding balls and similar articles for mills, of iron or steel, forged or stamped, but not further worked8,2109,0319,85210,673(C)
7326 19Articles of iron or steel, forged or stamped, but not further worked, n.e.s. (excl. grinding balls and similar articles for mills)8,2109,0319,85210,673(C)
7326 20 00Articles of iron or steel wire, n.e.s.8,2309,0539,87610,699(C)
7326 90 30Ladders and steps, of iron or steel8,2309,0539,87610,699(C)
7326 90 40Pallets and similar platforms for handling goods, of iron or steel8,2309,0539,87610,699(C)
7326 90 50Reels for cables, piping and the like, of iron or steel8,2309,0539,87610,699(C)
7326 90 60Ventilators, non-mechanical, guttering, hooks and like articles used in the building industry, n.e.s., of iron or steel8,2309,0539,87610,699(C)
7326 90 92Articles of iron or steel, open-die forged, n.e.s.8,2109,0319,85210,673(C)
7326 90 94Articles of iron or steel, closed-die forged, n.e.s.8,2109,0319,85210,673(C)
7326 90 96Sintered articles of iron or steel, n.e.s.8,2109,0319,85210,673(C)
7326 90 98Articles of iron or steel, n.e.s.8,2509,0759,90010,725(C)

anchor annex_IV · hash 8df8c7260d66a8512edfbd149e8d6c62a0d9ee659859397e5b9c665ec177f086